REMOTE CONTROLLER OWNER’S MANUAL IMPORTANT NOTE: Thank you for purchasing our air conditioner. Please read this manual carefully before operating your new air conditioning unit. Make sure to save this manual for future reference.
Table of Contents Remote Controller Specifications ......................................................02 Handling the Remote Controller ....................................................03 Buttons and Functions ...................................................................04 Remote Screen Indicators ..............................................................07 How to Use Basic Functions ..........................................................08 How to Use Advanced Functions ..................
Remote Controller Specifications RG10B(D)/BGEF, RG10B(D1)/BGEFU1, RG10B1(D)/BGEF, RG10B2(D)/BGCEF, RG10B10(D)/BGEF, RG10A4(D)/BGEF, RG10A4(D1)/BGEFU1, RG10A5(D)/BGEF, RG10A5(D1)/BGEFU1, RG10A5(D1)/BGCEFU1, RG10A5(D)/BGCEF, RG10A11(D)/BGEF, 3.
Handling the Remote Controller Inserting and Replacing Batteries Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use. 1. Slide the back cover from the remote control downward, exposing the battery compartment. 2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment. 3. Slide the battery cover back into place.
Buttons and Functions Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual. ON/OFF Turns the unit on or off. MODE Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN NOTE: HEAT mode is not supported by the cooling only appliance.
ON/OFF Turns the unit on or off. MODE Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN NOTE: HEAT mode is not supported by the cooling only appliance. TEMP Increases temperate in 1°C increments. Max. temperature is 30°C. SLEEP Saves energy during sleeping hours. SET Scrolls through operation functions as follows: Follow Me( ) AP mode ( ) Follow Me( )... OK Used to confirm the selected functions The selected symbol will flash on the display area, press OK button to confirm.
ON/OFF Turns the unit on or off. MODE Scrolls through operation modes as follows: AUTO COOL DRY HEAT FAN NOTE: HEAT mode is not supported by the cooling only appliance. TEMP Increases temperature in 1OC(1OF) increments. Max. temperature is 30OC(86OF). ECO Press this button to enter the energy efficient mode. SET Scrolls through operation functions as follows: Fresh( ) Sleep( ) Follow Me( ) AP mode( ) Fresh...
Remote Screen Indicators Information are displayed when the remote controller is power up.
How to Use Basic Functions Basic operation ATTENTION! Before operation, please ensure the unit is plugged in and power is available. SETTING TEMPERATURE The operating temperature range for units is 17-30°C (62-86°F)/20-28 C. You can increase or decrease the set temperature in 1°C (1°F) increments. AUTO Mode In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT operation based on the set temperature. 1 3 1. Press the MODE button to select AUTO. 2 2.
DRY Mode (dehumidifying) 1. Press the MODE button to select DRY. 2. Set your desired temperature using the TEMP or TEMP button. 1 3. Press the ON/OFF button to start the unit. 3 NOTE:FAN SPEED cannot be changed in DRY mode. 2 1 3 FAN Mode 1. Press the MODE button to select FAN mode. 2. Press FAN button to select the fan speed: AUTO, LOW, MED or HIGH. 3. Press the ON/OFF button to start the unit. 2 NOTE: You can’t set temperature in FAN mode.
Setting the TIMER TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off. TIMER ON setting Press TIMER button to initiate the ON time sequence. Press Temp. up or down button for for multiple times to set the desired time to turn on the unit. Point remote to unit and wait 1sec, the TIMER ON will be activated. x5 TIMER 1sec ON /OFF MO DE FA N TE MP SLE EP SH OR CU T T TIM ER TIM ER ON OFF TIMER OFF setting Press TIMER button to initiate the OFF time sequence.
How to Use Advanced Functions Swing function Press Swing button 2s Swing Swing The horizontal louver will swing up and down automatically when pressing Swing button. Press again to make it stop. Keep pressing this button more than 2 seconds, the vertical louver swing function is activated. (Model dependent) LED DISPLAY 5s LED Press LED button Press this button to turn on and turn off the display on the indoor unit.
ECO function Press ECO button(some units) Press ECO button to enter the energy efficient mode. Note:This function is only available under COOL mode. ECO operation: Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 O C/75 OF, fan speed of Auto to save energy (only when the set temperature is less than 24O C/75 OF).
SHORTCUT function Press SHORTCUT button(some units) Push this button when remote controller is on, the system will automatically revert back to the previous settings including operating mode, setting temperature, fan speed level and sleep feature (if activated). If pushing more than 2 seconds, the system will automatically restore the current operation settings including operating mode, setting temperature, fan speed level and sleep feature (if activated ).
SET function SET SET OK or Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm. To cancel the selected function, just perform the same procedures as above.
The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details. CR275-RG10(D) 16117000A37344 2020.07.
技术要求: 尺寸A5,大度 80克双胶纸 装订,黑白