BUBBLEPACK 65W UNIVERSAL BATTERY PACK OPERATING INSTRUCTIONS Revision 1.0 www.blueshape.
The user is being alerted of the importance of going through the literature accompanying this product and getting familiarised with the important safety and operating instructions, included. Moreover, please follow the safety instructions below. • • • • • • • • • • 2 Read the supplied instructions thoroughly and keep handy. Protect the equipment from humid environments. Avoid any contact with water or other fluids. Do not use if any liquid has been accidentally spilled inside the equipment.
Package contents • • • • • Bubblepack 65Wh battery Camera Adapter base Battery charger with mains cable BSTAP connector with 50cm cable Operating manual Introduction Bubblepack is a universal 65Wh, battery pack with multiple voltage outputs. The device is intended for fixing underneath a camera to supply power to it and its accessories. The whole arrangement can also be mounted on a tripod if needed. Outputs Range Connection Designation 14.8V /7A max 12.6V min ~ 16.8V max 2 x D-TAP HIGH 11.
Bubblepack graphic description (Battery) Locking arm Adapter rail 14.8V Right out D-TAP (hidden) 8.4/11.1V Right out BSTAP (BLUE-hidden) 14.8V Left out D-TAP 8.4/11.
Principle of operation Bubblepack internally contains 8 high quality Li-ion battery cells that can deliver a total of 65Wh. A battery management system and a high efficiency step-down converter create a choice of 3 voltage outputs - those most widely used in today's latest miniDV and DSC cameras: • 14.8V nominal • 11.2V regulated and fixed • 8.4V regulated and fixed The safety circuit features the usual, over and under voltage battery protections together with full output short circuit protections.
Auto turn-off modes Further features include 'sleep mode' to minimise battery drain during inactivity and when the battery pack reaches a low voltage threshold of 12.6V. In 'sleep mode', the internal microprocessor goes to low power mode thus minimising battery consumption. The battery can go to sleep mode in 3 ways: • • • automatically, if pack voltage is < 12.6V if there is no activity for 60 minutes if the test button is pressed for > 3 seconds until the LED closest to the push button flashes.
How to charge Bubblepack A fast charger has been included in the package. Simply connect the charger to one of the HIGH outputs on Bubblepack and the device will charge. It is expected that the device reaches full charge from empty within 2 ~ 3 hours. The LED on the charger will be red during charging but will turn to green when charge is completed. It is recommended to charge Bubblepack on first use or after a long period of shelf life or inactivity.
How to mount the camera 1. Position adapter base underneath the camera 8 2. View showing camera thread and alignment hole 3. Use a coin to screw in the adapter bolt into the camera Slide battery in this direction and determine the best lock-notch for best equilibrium 4.
Technical specifications Internal battery: Cell type Nominal voltage -HIGH Regulated Voltage -LOW (1) Regulated voltage -LOW (2) Nominal capacity Max. discharge current (D-TAP) Max. discharge current (BSTAP) Max output ripple content Operating temperature range Storage temperature range Li-Ion cylindrical rechargeable battery cells 14.8V (range 12.6 - 16.8V) 11.2V +/- 2% 8.4V +/- 2% 4.
Warranty BLUESHAPE Bubblepack is warranted to be free from defects in materials, workmanship and functionality for a period of 18 months commencing from the date of purchase. This warranty shall not apply to any products or parts of, that have been subjected to misuse, negligence, accidental or abnormal conditions of operation. The buyer should always contact the place of purchase for any return of defective product.
NEW CELL TOP Srl VIA LIGURIA 4-6, 42100 REGGIO EMILIA, ITALY TEL. +39 0522 518556 FAX. +39 0522 277084 WEB: www.blueshape.net EMAIL: info@blueshape.