Installation

BLUESTAR REFRIGERATOR INSTALLATION INSTRUCTIONS—DO NOT DISCARD
© Prizer Painter Stove Works, Blandon, PA 19510
Step 4 — Level Refrigerator
 The height adjustment for the front and back can
be made from the front of the refrigerator. Turn
the hex bolt clockwise with a 1/2” socket wrench
to raise the refrigerator or counterclockwise to
lower it. The refrigerator is designed to raise a
maximum of 1” from the shipped posion. Do not
aempt to raise the refrigerator beyond that point
as damage to the leveling system will occur.
Important: Do not use a power drill and do not over-ghten the leveling bolts. Level the
refrigerator to the oor, not the surrounding cabinetry, as this could aect door closing.
When the refrigerator is properly leveled, door and drawer adjustment are less likely to
be necessary.
 Once the refrigerator is level, extend the front feet to the oor and hand-ghten an
addional half turn. These feet will help stabilize the refrigerator.
Step 5 — Align Doors and Top Grille (if necessary)
Only adjust the doors and/or top grille if is necessary to achieve uniform gaps and
proper alignment.
Refrigerator Door
Important: Adjust the top hinge or boom hinge bolts. Do not loosen the top and
boom hinge bolts at the same me.
 Loosen four bolts with a 5/16” hex head socket.
 Slide door le or right as necessary to achieve
uniform gaps on the sides and/or between the
upper door and lower drawer.
 Reghten the bolts. Bolts need to be ghtened
to 50 in. lb. It is normal for the door to lower and
lt slightly when loaded with food.
 Repeat process for the boom of the door if
necessary.
Freezer Drawer
Important: Adjust one side at a me.
 Remove the middle bolt from the side mounng
bracket with a 5/16” hex head socket. Discard
the bolt as it is a pilot screw for inial assembly
only.
 Loosen the remaining two bolts from the side
mounng bracket and the divider screw from the
center of the drawer.
 Slide the door up or down as necessary to
achieve uniform gaps between the upper door
and lower drawer.
 Reghten the bolts. Bolts needs to be ghtened to 50 in. lb.
 Repeat process as necessary for the other side.
Top Grille
 Top grille can be adjusted vercally where hinge aaches to the grille. Grille can be
adjusted horizontally where hinge base is aached to the upper cabinet frame.
 Loosen Phillips screws and adjust grille as needed. Reghten screws.
Part # 799631 revision 0
Up
Back
Front
Tip Over Hazard
Front leveling legs must be rmly in contact with the oor to reduce the possibility of the
refrigerator pping forward. Failure to follow these instrucons can result in death or
serious injury.
WARNING
Risque de renversement
Les pieds de nivellement avant doivent être fermement en contact avec le plancher pour
réduire le risque de renversement du réfrigérateur vers l'avant. Le non-respect de ces
instrucons peut entraîner la mort ou des blessures graves.
AVERTISSEMENT
Adjust
Loosen
Loosen
Adjust
Remove pilot bolt.
Discard.
Step 6 — Anchor Refrigerator and Install Toe Grille
 Tighten the 1/2” anchor bolts through the top of the cabinet to the anchor brackets
with a 1/2” socket wrench. Close the top grille.
 Aach the upper toe grille to the brackets at the
base of the refrigerator with one black Phillips
screw on each side. Brackets may be adjusted side
to side if necessary to improve the t to the
enclosure.
 Aach the lower toe grille using one black Phillips
screw on each side. Boom of the toe grille should
rest on the oor.