Installation Sheet

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HF Face Frame Bi-Fold Cabinet Telescopic Arm Set for Cabinet Height of 35" to 42"

Subject to technical modiﬁcations

AVENTOS HF

Narrow aluminum door application

Telescopic arm set

■ Telescopic arm (qty 2)

Cabinet heights Part no.

479 (18-7/8") — 558 (22")

20F3200

558 (22") — 686 (27")

20F3500

686 (27") — 889 (35")

20F3800

889 (35") — 1067 (42")

20F3900

Cover set

■ Right and left cover plate

■ Non-handed cover cap (qty 2)

Part no.

Cover set

20F8000.NA

Lift mechanism set

■ Lift mechanism (qty 2)

■ #7 x 35 mm (1-3/8”) wood screw (qty 10)

Power factor Part no.

85 — 230 (1 lift mechanism req.)

20F2200.N5

231 — 470

20F2200.N5

471 — 880

20F2500.N5

780 — 1440

20F2800.N5

1401 — 2300 (3 lift mechanisms req.)

20F2800.N5

Narrow aluminum door hardware set

■ 72T550A.TL — CLIP top free swing narrow alum. top door hinge (qty 2)

■ 78Z550AT — CLIP top narrow aluminum bottom door hinge (qty 2)

■ 175H5400 — Top door mounting plate (qty 2)

■ 175H5A00 — Bottom door mounting plate (qty 2)

■ 175H5B00 — Telescopic arm mounting plate (qty 4)

■ 669.110 — Aluminum screw for the bottom door mounting plate, bottom hinge,

top hinge and telescopic arm mounting plate (qty 8)

NOTE: Three hinges and mounting plates are required for cabinet widths over 1219 (48”) or combined

door weight of 26.5 lb

Narrow aluminum door hardware set

78Z550ATA5

Installation screw for top mounting plate

606N or 606P

Summary of content (12 pages)

PAGE 1
AVENTOS HF Narrow aluminum door application Lift mechanism set ■■ Lift mechanism (qty 2) ■■ #7 x 35 mm (1-3/8”) wood screw (qty 10) Power factor Part no. 85 — 230 (1 lift mechanism req.) 20F2200.N5 231 — 470 20F2200.N5 471 — 880 20F2500.N5 780 — 1440 20F2800.N5 1401 — 2300 (3 lift mechanisms req.) 20F2800.N5 Cover set ■■ Right and left cover plate ■■ Non-handed cover cap (qty 2) Part no. 20F8000.NA Cover set Telescopic arm set ■■ Telescopic arm (qty 2) Cabinet heights Part no.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm Do not push lever arm down or leave in the down position Remove mechanism before installing or removing cabinet 192 37 TDH 5 TR Locating pin locations Y 1 TR = Top reveal TDH = Top door ht. Top door height (TDH) Y 231 to 271 TDH x .6 - 28 + TR 272 to 531 TDH x .6 - 57 + TR Universal individual template is available for pre-boring 5 mm locating pins 2 Part no. 65.1051.01 Subject to technical modifications without notice.
PAGE 3
2 Attach the lift mechanism a. Use the AVENTOS template to prebore the locating pin holes for the AVENTOS HF lift mechanism. b. After aligning the lift mechanism with the cabinet using the locator pins,attach the mechanism with the four mounting screws provided. #7 x 35mm (1-3/8“) wood screws (qty 5) 3 Attach the telescopic arms WARNING: Risk of injury from spring loaded arm. Attach telescopic arms by clipping them on in the fully upright position.
PAGE 4
Assembly 5 Top door hinge planning 21 19 15 1.7 66 Part no. Aluminum door hinge In-line mounting plate Bottom door hinge planning 21 3 66 6 72T550A 175H5100.05 Part no. Aluminum door bottom hinge Bottom door mounting plate 4 78Z550AT 175H5A00 Subject to technical modifications without notice.
PAGE 5
Frame preparation 22 4 11. R4 1.4 Bottom door planning Top door height (TDH) TDH 8 6 6 1 17 .4 38 44 38 R4 42 12. 5 31 22 7 90 19 - 1.1 – 0.1 7 X 231 to 271 TDH x .5 + 70 272 to 531 TDH x .5 + 47 min. 17 X NOTE: 3 hinges are required for cabinet width over 1219 mm (48") or 26.5 lb. combined door weight Part no. Telescopic arm mounting plate Subject to technical modifications without notice.
PAGE 6
Assembly 9 Attach the top door Determine the locations of mounting plates and hinges and attach the hardware to cabinet doors. Attach top door to the cabinet. 10 Attach the bottom door 1 2 Attach bottom door to the top door and attach the telescopic arms. 6 Subject to technical modifications without notice.
PAGE 7
11 Adjust the top door hinge Adjust each top door hinge and mounting plate to properly align the top door to the cabinet. ± 3 mm 12 ± 2 mm + 3/- 2 mm Adjust the bottom door hinge Adjust each bottom door hinge and mounting plate to properly align doors to the cabinet and to the top door. ± 2.5 mm Subject to technical modifications without notice.
PAGE 8
Assembly 13 Finalize the tension adjustments 1 2 Use #2x2 POZI bit Close and flush doors to cabinet. Open and close door to test closing force. Open door and adjust tension screws on both lift mechanisms with a power drill. Test door again and repeat until desired function is achieved. Tension adjustment should be the same on both lift mechanisms. 12 Lock telescopic arms 1 2 Open door enough to lock levers 1. Close and flush doors to cabinet.
PAGE 9
15 Attach cover caps Attach the left and right cover plates to each lift mechanism then attach the symmetrical cover caps. Subject to technical modifications without notice.
PAGE 10
Removal WARNING Risk of injury from spring-loaded arm Do not push lever arm down or leave in the down position Remove mechanism before installing or removing cabinet 1 Removing the covers 2 Removing the door Release both arms and gently rest the top door on the loose arms. The tension will hold the doors up for the next step. 1 2 10 Subject to technical modifications without notice.
PAGE 11
3 Removing the doors 1 2 1. Hold the bottom door while unclipping the bottom hinge. 4 2. Hold the top door while detaching the top hinges. Simply unclip them if using the CLIP top hinges or unscrew them if using COMPACT. Removing the telescopic arms 1 2 Using a screwdriver, depress the release tabs to remove telescopic arms. Subject to technical modifications without notice. © 2010 If transporting the cabinet to the jobsite, stop here.
PAGE 12
Other information Inch Door clearance above cabinet /32 .031 1 /16 .063 1.5 /32 .094 2 1 /8 .125 3 /32 .156 4 /16 .188 5 /32 .219 5.5 /4 .25 6 /32 .281 7 /16 .313 8 /32 .344 9 /8 .375 9.5 /32 .406 10 /16 .438 11 /32 .469 12 /2 .5 13 /32 .531 13.5 /16 .563 14 /32 .594 15 /8 .625 16 /32 .656 17 /16 .688 17.5 /32 .719 18 /4 .75 19 /32 .781 20 /16 .813 20.5 /32 .844 21 /8 .875 22 /32 .906 23 /16 .938 24 /32 .969 24.