Installation Sheet

ManualsBrandsBlum ManualsLift SystemsBlum AVENTOS HK Face Frame Cabinet Lift Mechanism Set with Power Factor of 100 - 174

Subject to technical modiﬁcations

AVENTOS HK

Narrow aluminum door application

Lift mechanism set

■

Lift mechanism (qty 2)

■

#7 x 35 mm (1-3/8”) wood screw (qty 10)

Power factor Opening angle Part no.

43 — 99 107°

20K2300.N5

100 — 174 107°

20K2500.N5

175 — 349 107°

20K2700.N5

350 — 792 100°

20K2900.N5

Cover set

■ Right and left cover plate

■ Non-handed cover cap (qty 2)

Part no.

Cover set

20K8000.NA

Narrow aluminum hardware set

■ Arm assembly mounting plate (qty2)

■ 669.110 — Aluminum screw for narrow aluminum lever arm

mounting plate (qty 8)

Part no.

Narrow aluminum hardware set

20S4200A

Summary of content (8 pages)

PAGE 1
AVENTOS HK Narrow aluminum door application Lift mechanism set ■■ Lift mechanism (qty 2) ■■ #7 x 35 mm (1-3/8”) wood screw (qty 10) Power factor 43 Opening angle — 99 100 — 174 Part no. 107° 20K2300.N5 107° 20K2500.N5 175 — 349 107° 20K2700.N5 350 — 792 100° 20K2900.N5 Cover set ■■ Right and left cover plate ■■ Non-handed cover cap (qty 2) Part no. 20K8000.NA Cover set Narrow aluminum hardware set ■■ Arm assembly mounting plate (qty2) ■■ 669.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm Do not push arm assembly down or leave in the down position Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth 77 1 5 128 37 261 Part no. Universal individual template is available for pre-boring 5 mm locating pins 2 65.1051.
PAGE 3
Remove transport tab from lift mechanism and raise arms A B Raise the arm to the upright position. Carefully remove the transport tab. Risk of injury from spring loaded arm. NOTE: Do not remove transport tab until just before attaching the door 4 Attaching the mounting plates 64 50 + Overlay 15.5 7 – 0.1 OL - 4.5 Attach the mounting plate to the door. Subject to technical modifications without notice. © 2010 When changing material thickness, adjust the assembly dimensions accordingly.
PAGE 4
Assembly 5 Attaching the door Attach the door using the CLIP mechanism in the mounting plate. 6 Adjust the door tension Use a screw gun and the supplied #2 x 2 POZI driver bit to adjust the lift mechanism to the desired tension. 4 Subject to technical modifications without notice.
PAGE 5
7 Finalize the door adjustments mm mm mm Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments. 8 Attach cover caps Snap the symmetrical cover caps on each cover plate. Place the left and right cover plates over the appropriate lift mechanisms and snap them in place. Subject to technical modifications without notice.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm Do not push arm assembly down or leave in the down position Remove mechanism before installing or removing cabinet 1 Removing the covers Remove the cover caps and cover plate. 2 ██ ██ Removing the door Open the door. Use a screwdriver to disengage the CLIP mechanism of the lever arm from the mounting plate Support the door with one hand and repeat on the other side 6 Subject to technical modifications without notice.
PAGE 7
Inch Other information .031 1 /16 .063 1.5 1 Panel door clearance /32 .094 2 1 /8 .125 3 /32 .156 4 /16 .188 5 /32 .219 5.5 /4 .25 6 /32 .281 7 /16 .313 8 /32 .344 9 /8 .375 9.5 /32 .406 10 /16 .438 11 /32 .469 12 /2 .5 13 /32 .531 13.5 /16 .563 14 /32 .594 15 /8 .625 16 /32 .656 17 /16 .688 17.5 /32 .719 18 /4 .75 19 /32 .781 20 /16 .813 20.5 /32 .844 21 /8 .875 22 /32 .906 23 /16 .938 24 /32 .969 24.5 1 25.
PAGE 8
Blum, Inc. 7733 Old Plank Rd. Stanley, NC 28164 800-438-6788 704-827-1345 fax 704-827-0799 sales.us@blum.com www.blum.com INST-AVT09-06.