Installation Guide

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HK-S Mounting Bracket for Face Frame Cabinets - Pair

AVENTOS HK

Lift mechanism set

▀ Lift mechanism (qty 2)

▀ #7 x 35 mm (1-3/8”) wood screw (qty 10)

Power factor Opening angle Part no.

43 — 99 107°

20K2300.N5

100 — 174 107°

20K2500.N5

175 — 349 107°

20K2700.N5

350 — 792 100°

20K2900.N5

Cover set

▀ Right and left cover plate

▀ Non-handed cover cap (qty 2)

Part no.

Cover set

20K8000.NA

Wood or wide alum door hardware set

▀ Arm assembly mounting plate (qty 2)

Hardware set

20S4200

Inst. screw for wood doors

606N or 606P

Inst. screw for wide alum doors

7072A

Mounting plate with bracket set

▀ Left and right mounting plate with bracket

▀ For large overlay ﬁve-piece doors

Part no.

Mounting plate w/ bracket set

20S4F01

Wood/wide aluminum

hardware set

Summary of content (7 pages)

PAGE 1
AVENTOS HK Wood/wide aluminum hardware set Lift mechanism set ▀▀ Lift mechanism (qty 2) ▀▀ #7 x 35 mm (1-3/8”) wood screw (qty 10) Power factor Opening angle Part no. 107° 20K2300.N5 100 — 174 107° 20K2500.N5 175 — 349 107° 20K2700.N5 350 — 792 100° 20K2900.N5 43 — 99 Cover set ▀▀ Right and left cover plate ▀▀ Non-handed cover cap (qty 2) Part no. 20K8000.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth 5 128 Face frame 77 Panel 68.5 1 5 37 128 Z 261 261 NOTE: Face frame cabinets must be blocked out flush with the frame. Overlay up to 28 32 35 Z 37 35 33 Part no. Universal individual template is available for pre-boring locating pins 2 65.1051.
PAGE 3
Remove transport tab from lift mechanism and raise arms A B Carefully remove the transport tab. Raise the arm to the upright position. Risk of injury from spring loaded arm. NOTE: Do not remove transport tab until just before attaching the door Attaching the mounting plates 4a For Wood/wide aluminum doors 12.5 + Overlay 4b With bracket for five-piece doors ü 12.5 more▀than 6 Standard mounting plate works 32 32 32 50 + Overlay Panel 12.
PAGE 4
Assembly 5 Attaching the door Attach the door using the CLIP mechanism in the mounting plate. 6 Adjust the door tension Use a screw gun and #2 x 2 POZI driver bit to adjust the lift mechanism to the desired tension. 4 Subject to technical modifications without notice.
PAGE 5
7 Finalize the door adjustments Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments. 1 2 3 3 2 1 8 mm mm mm Attach cover caps Snap the symmetrical cover caps on each cover plate. Place the left and right cover plates over the appropriate lift mechanisms and snap them in place. Subject to technical modifications without notice.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet 1 Removing the covers Remove the cover caps and cover plate. 2 ▀▀ ▀▀ 6 Removing the door Open the door. Use a screwdriver to disengage the CLIP mechanism of the lever arm ▀ from the mounting plate Support the door with one hand and repeat on the other side Subject to technical modifications without notice.
PAGE 7
Other information Inch Panel and face frame clearance X Door thickness / .031 1 /16 .063 1.5 3 32 / .094 2 18 / .125 3 5 32 / .156 4 3 16 / .188 5 7 32 / .219 5.5 14 / .25 6 9 32 / .281 7 / .313 8 1 Door thickness 16 19 22 26 5 16 X 70 59 49 35 11 Blum, Inc. 800-438-6788 sales.us@blum.com blum.com Subject to technical modifications without notice. © 2015 INST-AVT08-04.15 mm 1 32 /32 .344 9 3 8 / .375 9.5 13 32 / .406 10 7 16 / .