Installation Sheet

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HL Face Frame Lift-Up Cabinet Arm Assembly Set for Cabinet Heights of 13-13/16" to 15-11/16"

Subject to technical modiﬁcations

AVENTOS HL

Narrow aluminum frame door application

Oval stabilizer rod

■ Oval stabilizer rod

■ Aluminum rod length 1061 (41-3/4"), cut to size

■ Length

interior cabinet opening minus 122 (4-13/16")

Part no.

Oval stabilizer rod

20Q1061UA

NOTE: For cabinets wider than 48" two stabilizer rods and stabilizer rod connector set required

Cover set

■ Right and left cover plate

■ Non-handed cover caps

Part no.

Cover set

20L8000.N1

Lift mechanism set

■ Lift mechanism (qty 2)

■ #7 x 35 mm (1-3/8") wood screw (qty 10)

20L2100.N5

20L2300.N5

20L2500.N5

20L2700.N5

20L2900.N5

Arm assembly set

■ Right and left arm assembly

■ Stabilizer rod adapter (qty 2)

■ Stabilizer rod cover cap (qty 2)

Cabinet height Part no.

300 (11-13/16") — 349 (13-3/4")

20L3200.05

350 (13-13/16") — 399 (15-13/16")

20L3500.05

400 (15-3/4") — 550 (21-5/8")

20L3800.05

450 (17-11/16") — 580 (22-13/16")

20L3900.05

Narrow aluminum hardware set

■ Arm assembly mounting plate (qty2)

■ 699.110 — Aluminum screw for narrow aluminum lever arm

mounting plate (qty 8)

Part no.

Narrow aluminum hardware set

20S4200A

Summary of content (8 pages)

PAGE 1
AVENTOS HL Narrow aluminum frame door application Lift mechanism set ■■ Lift mechanism (qty 2) ■■ #7 x 35 mm (1-3/8") wood screw (qty 10) 20L2100.N5 20L2300.N5 20L2500.N5 20L2700.N5 20L2900.N5 Cover set ■■ Right and left cover plate ■■ Non-handed cover caps Part no. Cover set 20L8000.N1 Arm assembly set Right and left arm assembly Stabilizer rod adapter (qty 2) ■■ Stabilizer rod cover cap (qty 2) ■■ ■■ Cabinet height Part no. 20L3200.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm Do not push arm assembly down or leave in the down position Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth 88 1 192 37 278 min. Part no. Universal individual template is available for pre-boring 5 mm locating pins 2 65.1051.
PAGE 3
Attaching the arm assembly Risk of injury from spring loaded arm NOTE: Before starting, see safety note on page 2 Find the right and left arm assemblies and match them to the correct side of the cabinet A B Attach the arm assembly to the lift mechanism as shown in illustrations A and B. 4 Lift up on the arm assembly to lock into place. Attaching the stabilizer rod Cut the stabilizer rod to fit the cabinet.
PAGE 4
Assembly Attaching the mounting plates 5b Mounting plate position Attach the mounting plate to the door. Planning narrow alum. frames Overlay - 4.5 ø7 5a 4.6 31 38 33 64 X + Overlay 31 1.1 7.5 1.4 min 153.5 20L3500 203.5 20L3800 253.5 20L3900 303.5 11.4 X 20L3200 6 15 — 19 12.5 NOTE: All four screws must be installed Arm assembly 7.5 max Reveal (1 — 4) When changing material thickness, Overlay adjust the assembly dimensions accordingly.
PAGE 5
7 Adjusting the lift mechanism tension Use a screw gun and the supplied #2x2 POZI driver bit to adjust the lift mechanism to the desired tension. 8 Adjusting the door Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments. Tension should be the same on both lift mechanisms. ± 2 mm 9 ± 2 mm ± 2 mm Attach covers Snap the symmetrical cover caps on each cover plate.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm Do not push arm assembly down or leave in the down position Remove mechanism before installing or removing cabinet 1 Removing the door Open the door. Support the door with one hand and push down tab to disengage the CLIP mechanisms of the arm assemblies of the mounting plates. 2 1 Lift the door off the mounting plates. 2 Remove the covers Remove the cover caps and cover plate.
PAGE 7
4 Removing the arm assembly 2 1 Use a screwdriver to disengage both arm assemblies. Remove arm assembly from mechanism. NOTE: Both tabs must be disengaged Subject to technical modifications without notice.
PAGE 8
Other information Inch .031 1 /16 .063 1.5 /32 .094 2 1 /8 .125 3 /32 .156 4 /16 .188 5 /32 .219 5.5 /4 .25 6 /32 .281 7 /16 .313 8 /32 .344 9 /8 .375 9.5 /32 .406 10 /16 .438 11 /32 .469 12 /2 .5 13 /32 .531 13.5 /16 .563 14 /32 .594 15 /8 .625 16 /32 .656 17 /16 .688 17.5 /32 .719 18 /4 .75 19 /32 .781 20 /16 .813 20.5 /32 .844 21 /8 .875 22 /32 .906 23 /16 .938 24 /32 .969 24.5 1 25.