Installation Guide

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HS Up-And-Over Lift Mechanism For Cabinet Doors Up To 31 Inches High with Max Weight of 17 Pounds

AVENTOS HS

Lift mechanism set

▀ Lift mechanism (qty 2)

▀ #7 x 35 mm (1-3/8”) wood screw (qty 10)

Part no.

20S2A00.N5 20S2B00.N5 20S2C00.N5

20S2D00.N5 20S2E00.N5 20S2F00.N5

20S2G00.N5 20S2H00.N5 20S2I00.N5

Round stabilizer rod

▀ Aluminum rod length 1061 (41-3/4"), cut to size

▀ Length

interior cabinet opening minus 129 (5-1/16")

Part no.

Round stabilizer rod

20Q1061UN

NOTE: For cabinets wider than 48" two stabilizer rods and a stabilizer rod connector set required

Arm assembly set

▀ Right and left arm assembly

▀ Stabilizer rod cover cap (qty 2)

Arm assembly set

20S3500.06

Cover set

▀ Right and left cover plate

▀ Non-handed cover caps (qty 2)

Part no.

Cover set

20S8000.NA

Wood/wide aluminum door hardware set

▀ Arm assembly mounting plate (qty 2)

Part no.

Mounting plate set

20S4200

Installation screw for wood

606N or 606P

Installation screw for alum

7072A

Mounting plate with bracket set

▀ Right and left mounting plates Part no.

Plate w/ bracket set

20S4F01

Wood/wide aluminum

hardware set

Summary of content (8 pages)

PAGE 1
AVENTOS HS Wood/wide aluminum hardware set Lift mechanism set ▀▀ Lift mechanism (qty 2) ▀▀ #7 x 35 mm (1-3/8”) wood screw (qty 10) Part no. 20S2A00.N5 20S2B00.N5 20S2C00.N5 20S2D00.N5 20S2E00.N5 20S2F00.N5 20S2G00.N5 20S2H00.N5 20S2I00.N5 Cover set ▀▀ Right and left cover plate ▀▀ Non-handed cover caps (qty 2) Part no. 20S8000.NA Cover set Arm assembly set ▀▀ Right and left arm assembly ▀▀ Stabilizer rod cover cap (qty 2) 20S3500.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet 1 Locating pin locations and minimum depth Face frame 80 80 Panel NOTE: Face frame cabinets must be blocked out flush with the frame. Universal individual template is available for pre-boring 5 mm locating pins 2 Part no. 65.1051.
PAGE 3
Attaching the arm assembly 1 2 a1 b2 Before starting, see safety note on page 2 1. Find the right and left arm assemblies and match them to the correct side of the cabinet. 2. Attach the arm assembly to the lift mechanism as shown. 3. Lift up on the arm assembly to lock into place. 3 Risk of injury from spring loaded arm. 4 Attaching the stabilizer rod Cut the stabilizer rod to fit the cabinet.
PAGE 4
Assembly 5a For Wood/wide aluminum doors 5b For five-panel doors 12.5 + Overlay 64 NOTE: Attach with four 606 wood screws 6 ü Standard mounting plate does not work 12.5 less▀than 6 Use mounting plate with bracket when panel is < 6 mm from screw ü Plate w/ bracket set Attaching the door Attach the door using the CLIP mechanism to the arm assembly 4 12.5 more▀than 6 32 32 32 15.5 197 + Overlay Standard mounting plate works Subject to technical modifications without notice. © 2015 12.
PAGE 5
7 Adjusting the lift mechanism tension Use a screw gun and the supplied #2 x 2 POZI driver bit to adjust the lift mechanism to the desired tension. 8 9 Adjusting the door Snap the symmetrical cover caps on each cover plate. Place the left and right cover plates over the appropriate lift mechanisms and snap them in place. Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet 1 Removing the door Open the door. Use a screwdriver to disengage the CLIP mechanism of the arm assembly from the mounting plate. 2 Remove the covers Remove the left and right cover plates. 6 Subject to technical modifications without notice.
PAGE 7
3 Remove the stabilizer rod Pull back the stabilizer rod cover caps and loosen the locking screw on each end of the stabilizer rod. Remove the Stabilizer rod from the cabinet. 4 Removing the arm assembly a Use a screwdriver to disengage the arm assembly as shown. b Remove arm assembly from mechanism. Cabinet is now ready for transport. a b Subject to technical modifications without notice.
PAGE 8
Other information Inch Panel door protrusion for common cabinet heights / .031 1 /16 .063 1.5 3 32 / .094 2 18 / .125 3 5 32 / .156 4 3 16 / .188 5 7 32 / .219 5.5 14 / .25 6 9 32 / .281 7 5 16 / .313 8 1 600 22 227 460 137 96 67 144 350 800 646 /32 .344 9 3 8 / .375 9.5 13 32 / .406 10 7 16 / .438 11 15 32 / .469 12 12 / .5 13 17 32 / .531 13.5 9 16 / .563 14 19 32 / .594 15 58 / .625 16 21 32 / .656 17 11 16 / .