Narrow Aluminum Door Installation Guide

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HS Up-And-Over Lift Mechanism For Cabinet Doors Up To 31 Inches High with Max Weight of 17 Pounds

AVENTOS HS

Lift mechanism set

▀ Lift mechanism (qty 2)

▀ #7 x 35 mm (1-3/8”) wood screw (qty 10)

Part no.

20S2A00.N5 20S2B00.N5 20S2C00.N5

20S2D00.N5 20S2E00.N5 20S2F00.N5

20S2G00.N5 20S2H00.N5 20S2I00.N5

Round stabilizer rod

▀ Aluminum rod length 1061 (41-3/4"), cut to size

▀ Length

interior cabinet opening minus 129 (5-1/16")

Part no.

Round stabilizer rod

20Q1061UN

NOTE: For cabinets wider than 48" two stabilizer rods and a stabilizer rod connector set required

Arm assembly set

▀ Right and left arm assembly

▀ Stabilizer rod cover cap (qty 2)

Part no.

Arm assembly set

20S3500.06

Cover set

▀ Right and left cover plate

▀ Non-handed cover caps (qty 2)

Part no.

Cover set

20S8000.NA

Narrow aluminum hardware set

▀ Arm assembly mounting plate (qty2)

▀

699.110 — Aluminum screw for narrow aluminum lever arm

mounting plate (qty 8)

Part no.

Narrow aluminum hardware set

20S4200A

Narrow aluminum

frame door application

Summary of content (8 pages)

PAGE 1
AVENTOS HS Narrow aluminum frame door application Lift mechanism set ▀▀ Lift mechanism (qty 2) ▀▀ #7 x 35 mm (1-3/8”) wood screw (qty 10) Part no. 20S2A00.N5 20S2B00.N5 20S2C00.N5 20S2D00.N5 20S2E00.N5 20S2F00.N5 20S2G00.N5 20S2H00.N5 20S2I00.N5 Cover set ▀▀ Right and left cover plate ▀▀ Non-handed cover caps (qty 2) Part no. 20S8000.NA Cover set Arm assembly set ▀▀ Right and left arm assembly ▀▀ Stabilizer rod cover cap (qty 2) Part no. 20S3500.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth 80 1 Universal individual template is available for pre-boring 5 mm locating pins 2 Part no. 65.1051.02 Attaching the lift mechanism Align the lift mechanism in the cabinet using the 5 mm locator pins and attach the mechanism with the five wood screws provided. 5 min.
PAGE 3
Attaching the arm assembly a b 11 22 Before starting, see safety note on page 2 a. Find the right and left arm assemblies and match them to the correct side of the cabinet. b. Attach the arm assembly to the lift mechanism as shown. c. Lift up on the arm assembly to lock into place. c Risk of injury from spring loaded arm. 4 Attaching the stabilizer rod Cut the stabilizer rod to fit the cabinet.
PAGE 4
Assembly 5a 5b Mounting plate position Planning narrow alum. frames Attach the mounting plate to the door. 15 to 19 NOTE: When changing material thickness, adjust assembly dimensions. 197 + Overlay 19 to ov erl overlay 33 38 31 1.1 Ø7– 0.1 32 32 32 38 31 12.5 + Overlay 90° 15.5 reveal (1 to 4) 64 197 + Overlay 11.4 12.5 R4 7.5 1. 4 mi n.
PAGE 5
7 Adjusting the lift mechanism tension Use a screw gun and the supplied #2 x 2 POZI driver bit to adjust the lift mechanism to the desired tension. 8 9 Adjusting the door Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments. 3 1 mm 2 mm 2 Attach covers Snap the symmetrical cover caps on each cover plate. Place the left and right cover plates over the appropriate lift mechanisms and snap them in place.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet 1 Removing the door Open the door. Use a screwdriver to disengage the CLIP mechanism of the arm assembly from the mounting plate. 2 Remove the covers Remove the left and right cover plates. 6 Subject to technical modifications without notice.
PAGE 7
3 Remove the stabilizer rod Pull back the stabilizer rod cover caps and loosen the locking screw on each end of the stabilizer rod. Remove the Stabilizer rod from the cabinet. 4 Removing the arm assembly a Use a screwdriver to disengage the arm assembly as shown. b Remove arm assembly from mechanism. Cabinet is now ready for transport. a b Subject to technical modifications without notice.
PAGE 8
Other information Inch Panel door protrusion for common cabinet heights / .031 1 /16 .063 1.5 3 32 / .094 2 18 / .125 3 5 32 / .156 4 3 16 / .188 5 7 32 / .219 5.5 14 / .25 6 9 32 / .281 7 5 16 / .313 8 1 600 22 227 460 137 96 67 144 350 800 646 /32 .344 9 3 8 / .375 9.5 13 32 / .406 10 7 16 / .438 11 15 32 / .469 12 12 / .5 13 17 32 / .531 13.5 9 16 / .563 14 19 32 / .594 15 58 / .625 16 21 32 / .656 17 11 16 / .