Narrow Aluminum Door Installation Guide

ManualsBrandsBlum ManualsView All BlumBlum AVENTOS HL SERVO-DRIVE Lift Arm Assembly Set For Cabinet Doors Up To 15-13/16 Inches High

AVENTOS HL

Oval stabilier rod

▀ Oval stabilizer rod

▀ Aluminum rod length 1061 (41-3/4"), cut to size

▀ Length

interior cabinet opening minus 129 (4-13/16")

Part no.

Oval stabilizer rod

20Q1061UA

NOTE: For cabinets wider than 48" two stabilizer rods and stabilizer rod connector set required

Cover set

▀ Right and left cover plate

▀ Non-handed cover caps

Part no.

Cover set

20L8000.N1

Lift mechanism set

▀ Lift mechanism (qty 2)

▀ #7 x 35 mm (1-3/8") wood screw (qty 10)

20L2100.N5

20L2300.N5

20L2500.N5

20L2700.N5

20L2900.N5

Narrow aluminum hardware set

▀ Arm assembly mounting plate (qty2)

▀ 699.110 — Aluminum screw for narrow aluminum lever arm mounting

plate (qty 8)

Part no.

Narrow aluminum hardware set

20S4200A

Narrow aluminum

frame door application

Arm assembly set

▀ Right and left arm assembly

▀ Stabilizer rod cover cap (qty 2)

Part no.

300 (11-13/16" ) — 349 (13-3/4")

20L3200.06

350 (13-13/16") — 399 (15-13/16")

20L3500.06

400 (15-3/4") — 550 (21-5/8")

20L3800.06

450 (17-11/16") — 580 (22-13/16")

20L3900.06

Summary of content (8 pages)

PAGE 1
AVENTOS HL Narrow aluminum frame door application Lift mechanism set ▀▀ Lift mechanism (qty 2) ▀▀ #7 x 35 mm (1-3/8") wood screw (qty 10) 20L2100.N5 20L2300.N5 20L2500.N5 20L2700.N5 20L2900.N5 Cover set ▀▀ Right and left cover plate ▀▀ Non-handed cover caps Part no. 20L8000.N1 Cover set Arm assembly set ▀▀ Right and left arm assembly ▀▀ Stabilizer rod cover cap (qty 2) Part no. 300 (11-13/16") — 349 (13-3/4") 20L3200.06 350 (13-13/16") — 399 (15-13/16") 20L3500.
PAGE 2
Assembly WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet Locating pin locations and minimum depth 88 1 192 37 278 min. Part no. Universal individual template is available for pre-boring 5 mm locating pins 2 65.1051.02 Attaching the lift mechanism Align the lift mechanism in the cabinet using the 5 mm locator pins and attach the mechanism with the five wood screws provided.
PAGE 3
Attaching the arm assembly Risk of injury from spring loaded arm NOTE: Before starting, see safety note on page 2 Find the right and left arm assemblies and ▀ match them to the correct side of the cabinet 1 2 a Attach the arm assembly to the lift mechanism ▀ as shown in illustrations. 4 b Lift up on the arm assembly to lock into place. Attaching the stabilizer rod Cut the stabilizer rod to fit the cabinet.
PAGE 4
Assembly Attaching the mounting plates 5a 5b Mounting plate position Planning narrow alum. frames Attach the mounting plate to the door. 15 to 19 11.4 X + Overlay 12.5 NOTE: When changing material thickness, adjust assembly dimensions. 19 to ov erl reveal (1 to 4) 90° Ø7– 0.1 1.1 NOTE: All four screws must be installed 6 X 20L3200.06 153.5 20L3500.06 203.5 20L3800.06 253.5 20L3900.06 303.5 38 Arm assembly R4 7.5 1. 4 mi n.
PAGE 5
7 Adjusting the lift mechanism tension Use a screw gun and the supplied #2x2 POZI driver bit to adjust the lift mechanism to the desired tension. 8 Adjusting the door Use a POZI screwdriver to adjust cam adjustments for each of the three-dimensional adjustments. Tension should be the same on both lift mechanisms. 3 1 2 3 2 1 mm 9 mm mm Attach covers Snap the symmetrical cover caps on each cover plate.
PAGE 6
Removal WARNING Risk of injury from spring-loaded arm ▀▀ Do not push arm assembly down or leave in the down position ▀▀ Remove mechanism before installing or removing cabinet 1 Removing the door 2 1 Open the door. Support the door with one hand and push down on tab to disengage the CLIP mechanisms on the arm assemblies of the mounting plates. 2 Remove the covers Remove the cover caps and cover plate. 6 Subject to technical modifications without notice.
PAGE 7
oval / Démontage / Smontaggio / Desmontaje / Dem CS not glue the3 Blum dista nce bumper / Ne pas encoller la butée Blum / / Warning / Attention / Attenzione / Advertencia / Ostr Remove the Warnung stabilizer rod oduzca el distanciado r de amortiguación de Blum / DA ontaż アーム部分は下に向け Vystřelující ramena jsou zdrojem / Risikozeżenie for at komme til skade ved løfteanordning. Pull back the stabilizer rod cover caps and remove the stabilizer rod from arm assembly.
PAGE 8
Other information Space requirements Inch Panel Face frame / .031 1 /16 .063 1.5 3 32 / .094 2 18 / .125 3 5 32 / .156 4 3 16 / .188 5 7 32 / .219 5.5 14 / .25 6 9 32 / .281 7 5 16 / .313 8 Z 170 (6-9/16") 278 minimum Y 300 (11-13/16") to 580 (23") B 56 minimum A B 170 (6-9/16") Y 300 (11-13/16") to 580 (22-13/16") Z 1 A 56 minimum 278 minimum /32 .344 9 3 8 / .375 9.5 13 32 / .406 10 7 16 / .438 11 15 32 / .