Installation Manual

ManualsBrandsBlum ManualsCabinet HardwareBLUM 563H5330B Tandem Plus Blumotion 21" Drawer Runner Pair for Face Frame, Silver

TANDEM plus BLUMOTION

Dimensions in millimeters (inch equivalents as noted)

Side-to-side adjustment Rear side-to-side adjustment

Rotate side-to-side adjustment left or

right equally on both locking devices. Drawer

front moves in the same direction as rotation.

After front side-to-side adjustment is

made with the locking devices, rotate the

rear side-to-side adjustment left or right

to re-align the back of the drawer box with

the front. Drawer back moves in the same

direction as rotation.

Maximum 1.5 (1/16") to left or right in both front and rear (tool-free)

NOTE: Side-to-side adjustment not available on T51.x8xx locking devices

Height adjustment Tilt adjustment

Press up on adjustment tab

Push towards back of drawer

Maximum 3 (1/8") rise of drawer front (tool-free)

Rotate the tilt adjustment lever on the rear of

each runner to lift the back of the drawer and

tilt the top of the drawer front forward

Maximum 5 (3/16") rise of drawer back (tool-free)

NOTE: Height and tilt adjustments available with all combinations of locking devices and runners

Full extension concealed runners

Basic components Locking devices Runners Rear attachment options

Depth adjustment on runner

TANDEM 563 runners feature elongated

holes that allow ±4.5 (3/16") depth adjustment

Depth adjustable locking device

Locking device

with side-to-side,

height and

depth adjustment

Turning the adjustment screw allows

for up to a

2.5 (3/32") out adjustment

NOTE: For T51.1901.PS setback in inset

applications, see page 5

Drawer

front

L R

T51.1901.PS

563H/563. installation instructions563H/563. installation instructions

Summary of content (6 pages)

PAGE 1
TANDEM plus BLUMOTION 563H/563. installation instructions Full extension concealed runners Basic components Locking g devices Side-to-side adjustment Rear side-to-side adjustment 1 Rotate side-to-side adjustment left or right equally on both locking devices. Drawer front moves in the same direction as rotation. 2 After front side-to-side adjustment is made with the locking devices, rotate the rear side-to-side adjustment left or right to re-align the back of the drawer box with the front.
PAGE 2
TANDEM plus BLUMOTION Drawer speciﬁcations Preparing for hardware installation Drawer box speciﬁcations opening width Front view 6 (1/4") minimum top clearance outside drawer width opening width minus 42 75° Installation screw 606N or 606P Locking device T51.1901 with side-to-side adjustment or T51.1801 without side-to-side adjustment Screws or maximum drawer height = opening minus 20 (25/32") drawer side thickness maximum 16 (5/8") 2.5 mm bit with extension chuck (1-15/32") 37 662.1150.
PAGE 3
Face frame application TANDEM plus BLUMOTION Runner mounting speciﬁcations Cabinet and drawer speciﬁcations Side view inside cabinet depth cabinet face mounting position 10 (13/32") 610 (24") cabinet setback 3 (1/8") cabinet face bracket range 6 to 48 (1/4" to 1-7/8") 563H5330B rear bracket cabinet depth Side view inside cabinet depth range 557 to 599 (21-15/16" to 23-19/32") 533 (21") drawer runner length mounting position 10 (13/32") 557 (21-15/16") minimum 37 (1-15/32") 25 (31/32") set
PAGE 4
Panel application TANDEM plus BLUMOTION Runner mounting speciﬁcations Cabinet and drawer speciﬁcations Side view Side view mounting position 37 (1-15/32") cabinet face 256 (10-3/32") 224 (8-13/16") cabinet depth inside cabinet depth 610 (24") 563H5330B cabinet cabinet face 533 (21") drawer 18 (23/32") typical runner length setback 3 (1/8") 557 (21-15/16") minimum mounting position 37 (1-15/32") 224 (8-13/16") 37 (1-15/32") 610 (24") 563.
PAGE 5
TANDEM plus BLUMOTION Inset application Face frame application – complete blockout Face frame application – partial blockout Panel application Side view Side view Side view Runner setback (see table) Trial recommended Runner setback (see table) Trial recommended Blocking behind frame Runner setback (see table) Trial recommended Blocking behind frame inside cabinet depth inside cabinet depth range inside cabinet depth minimum = runner length + setback + 6 (1/4") minimum = runner length + set
PAGE 6
Attachment speciﬁcations TANDEM plus BLUMOTION Rear attachment options for face frame applications Depth adjustment speciﬁcations Front view Side view 295.3700.2x Rear mounting bracket, non-handed 21 (13/16") For 563H2290B10, non-handed 295.6410 Plug-in socket, non-handed 4 (5/32") 2 (3/32") 16 (5/8") face frame rail setback Mount each runner using at least two of the elongated holes. Install the drawer to check the position of the drawer front.