Instructions / Assembly

ManualsBrandsBluworld of Water ManualsKitchenClassic Quarry Large Nojoqui Falls Rainforest Brown Marble with Copper Vein Trim Kit Fountain

635 W. Michigan Street Orlando, FL 32805 · PH 407-426-7674 · Fax 407-426-7721

Page 1 of 8

CLASSIC QUARRY NOJOQUI

& HORIZON FALLS

Installation Manual

IMPORTANT – RETAIN FOR FUTURE REFERENCE – READ CAREFULLY

• Try to position your fountain above or near an electrical outlet.

• When considering the location of your fountain, please consider making it easily accessible for maintenance (e.g.

adding water, cleaning etc.). Avoid delicate surfaces that could be damaged by splashing.

• Consider the surface on which your waterfall will be placed. This feature can be mounted on sheetrock with

wood studs, tile, brick or concrete. (No mounting hardware is included for masonry installations). Due to the

weight of this fountain, it is necessary to mount directly into at least one wood stud. You MUST use the provided

EZ Anchors™ (J) for any screw that does not hit a stud.

• Mount indoors only. It is not recommended to place your fountain in direct sunlight.

• ** It is critical that your waterfall is level as this will ensure even water flow. **

• Assemble as near as possible to the point of installation. Take extreme care when lifting to avoid

personal injury or damage to the product.

• This product contains small items and plastic bags. Please be aware of the danger to young children.

• Assistance in mounting your fountain is required. You will need 2-3 people.

Summary of content (8 pages)

PAGE 1
CLASSIC QUARRY NOJOQUI & HORIZON FALLS Installation Manual IMPORTANT – RETAIN FOR FUTURE REFERENCE – READ CAREFULLY • • • • • • • • Try to position your fountain above or near an electrical outlet. When considering the location of your fountain, please consider making it easily accessible for maintenance (e.g. adding water, cleaning etc.). Avoid delicate surfaces that could be damaged by splashing. Consider the surface on which your waterfall will be placed.
PAGE 2
Parts List Not Shown - Classic Quarry Stone A. Bracket Template 1 each B. Stone Wall Bracket 1 each C. Remote 1 each D. Reservoir Wall Bracket 1 each E. Water Disperser 1 each F. Water Diffuser 1 each G. Trim Kit (your color may be different) 1 each H. Pump Assembly w/Flow Valve 1 each I. River Rocks 1 each J. Hardware Bag with scrubby pad M. Pocket Clips 2 each K. LED Light Kit with cord 1 each N. Rock Tray 1 each L. Reservoir 1 each O.
PAGE 3
Section 2: Mounting the Wall Brackets 1. Your Nojoqui Falls fountain is 58” tall x 25.5” wide the Horizon Falls fountain is 33” tall x 51” wide. Determine where on the wall the fountain will be mounted. You may wish to block out the dimensions with low tack or painters masking tape for reference. The fountain must be mounted into studs, wood or metal. Using the stud finder locate and mark the position of the vertical and horizontal studs within the blocked out installation area.
PAGE 4
Section 3: Mounting the Reservoir and Water Disperser 1. Locate the reservoir (L) and the EVA Cushion Strips (O). Peal the paper off the adhesive strip and place each pad about 1” up from the bottom of the reservoir and 2” in from each side as shown in the drawing (Fig 3.1). 2. Hang the reservoir (L) on the reservoir wall bracket (D). Make certain the reservoir (L) is well seated and centered on the bracket (Fig 3.2). 3. Place the pump assembly (H) inside the reservoir (L) close to the right edge.
PAGE 5
2. It is a good idea to have someone spot you on the position of the bracket and to see if you are centered or not inside the basin. Lift the stone up just past the mounting cleat and tip the top back so it is just under the disperser (E) and then tilt the bottom back towards the wall clearing the reservoir lip. Lower the stone until it engages the cleat. Make certain the stone is well seated on the cleat and centered from left to right inside the reservoir (L).
PAGE 6
Section 7: Installing the Light Kit 1. Carefully unwrap the LED light bar (K). Take care in handling so that the LED strips and connections to transformers are not disturbed. Remove the tie from the electrical cord. 2. Place the LED light bar (K) inside the header (G) with the LED strip facing down (Fig 7.1). It is designed to simply rest on the header held up by the 2 tabs located on either side of the light bar (G).
PAGE 7
RF Wireless Touching LED Remote Controller (Color Adjusting) 1. 2. 3.
PAGE 8
Warranty Bluworld’s Warranty has changed as of August 1, 2008 and supersedes all previous warranties for product purchased after August 1, 2008. If there is printed material within this shipment it is considered void and the Warranty as stated below is policy. Bluworld products are warranted against defects that render it unfit for its reasonably intended use.