INSTALLATION, OPERATION INSTRUCTIONS AND PARTS MANUAL SENSOR-OPERATED LAVATORY FAUCETS FOR BATTERY FOR PLUG-IN INSTALLATIONS B-8870 Polished Brass B-8872 Matte Black B-8875 Brushed Nickel B-8876 Polished Nickel B-8878 Polished Chrome Patented: PAT. www.Bobrick.com NOTICE: READ ENTIRE MANUAL PRIOR TO INSTALLING PRODUCT. NOTE: The information in this manual is subject to change at any time without notice. Installations may be performed at different times of construction by different individuals.
Package Contents Required Tools: Spout Assembly Allen Wrench (3/32") (Supplied) Aerator and Key Allen Wrench (M3) (Supplied) Shank Mounting Kit Base Gasket Electronics Box with Solenoid Phillips Head Screwdriver Non-toothed Wrench Batteries Filter Overview Designer Series Faucet features multiple spout design in a standard polished chrome finish with one piece heavy duty cast brass spout, advanced electronic components and feature sets.
Installation NOTE: Before installation, turn off water supplies to existing faucet and remove faucet if replacing an existing device. Clean the faucet basin and clear away debris. Flush all supply lines before connecting the faucet. Failure to do so may result in debris clogging the inlets and/or internal control and mixing valve Spout Installation - Step 1 1.1. Carefully screw aerator into spout using included tool. 1.2.
2.2a. Optional ACA version: Connect supplied inline connector and AC adapter. 2.2b. Optional HW6 (Hardwired 6V) version: Connect supplied inline connector and hardwire adapter. When securing the CWB wires to the screw terminals on HW6 unit, the BLACK WITH DASHED MARKINGS should be connected to the Positive (+) terminal, and the SOLID BLACK wire should be connected to the Negative (-) terminal.
Adjustable modes and features selection: To adjust features from default configuration, you must remove the battery tray. Once battery tray is removed you will see the switches. Before adjusting switches when electronics box is first installed or when replacing dead battery: 1. Temporarily install battery tray with fresh batteries installed and hold in place for 30 seconds. 2. Remove battery tray and set switches. 3. Re-install battery tray. All switches shown in default mode.
Troubleshooting Guide POTENTIAL SITUATIONS Faucet is non-responsive POSSIBLE CAUSES SUGGESTED SOLUTION TIPS Battery voltage low or no power Change out batteries or verify power provided by HW6 or ACA Sensor and electronic connector cable has bent or broken pins Check to see if pins are missing, bent, or broken. If yes, then the electronic box needs replaced Sensor lens could have surface damage, scratches, or deposit build ups Inspect the sensor lens underneath the spout tip.
Spout Replacement To replace spout body, you must first turn water off, then remove spout with sensor cable. Before removing the spout, disconnect the sensor cable below the deck so that the cable head can be pulled up through the deck. *Take care to press the locking mechanism in prior to disconnecting sensor cable. PULLING APART WITHOUT PRESSING IN THE LOCK MAY DAMAGE THE SENSOR OR CONTROLLER CABLES. Note location of set screw and spring lock.
Parts List 7 18 6 8 21 19 20 P6000-HW6 WIRING FRAM E/SAFETY GR OUN D GR EEN/YELLOW VAC IN BLU E (-) WHITE (NEU TRAL) BLACK (LINE) R ED (+) 16 17 9 11 1 Z6951 Spout Assembly with Sensor P6951-XL-1 11. Mixing Valve w/Filter P6900-XL-MV 2 Spout shank base for Z6950/Z6955-XL P6950-XL-B 12. Mixing Tee w/Filters and Back Checks P6900-XL-MT 3 Z6950 Spout base gasket P6950-XL-42 13. Single Stainless Supply Hose (XL) 4 Electronics Box with Solenoid P6950-XL-B-L 14.
Limited Warranty All goods sold hereunder are warranted to be free from defects in material and factory workmanship for a period of three years from the date of purchase. Decorative finishes warranted for one year. We will replace at no costs goods that prove defective provided we are notified in writing of such defect and the goods are returned to us prepaid at Sanford, NC, with evidence that they have been properly maintained and used in accordance with instructions.
In the United States: BOBRICK WASHROOM EQUIPMENT, INC. Los Angeles: 6901 Tujunga Avenue., North Hollywood, CA 91605-6213, Tel: (818) 982-9600, Fax: 818-503-9287 New York: 200 Commerce Drive, Clifton Park, NY 12065-1350, Tel: (518) 877-7444, Fax: 518-877-5029 or email customerservice@bobrick.
