Specification Sheet

ManualsBrandsBobrick ManualsSoap DispensersBobrick TrimLineSeries Wall Mounted Soap Dispenser

continued . . .

The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 2/29/16

Technical Data

217mm

16mm

65mm

260mm

108mm

153mm

116mm

310mm

Finish Face of Wall

Drilling Specifications

297mm

96mm

Recommended Mounting Height Off Floor

100-110cm

Plastic

Container

Lock

& Key

TrimLineSeries

SURFACE-MOUNTED

FOAM SOAP DISPENSER

500ML

MATERIAL:

Welded, 0.8mm (22 gauge) 1.4301, Typ CrNi 18/10, AISI 304 stainless steel housing with satin ﬁnish; stainless

steel operating lever; metal lock and key; soap level indicator; interchangeable plastic containers with plastic

pumps; variety of plastic containers available including containers with pumps for soap or foam.

OPERATION:

The cover is lockable with a Bobrick System lock. To reﬁll the dispenser, open the cover by lifting and pulling forward. The soap level

indicator shows how much product is remaining in the dispenser. The plastic container can be removed and re-installed for quick and

easy reﬁlling. The plastic container can be used for foam soap cartridges (up to 500 ml), as well as bulk reﬁlling of up to 500 ml of foam

soap. To install a soap cartridge in the dispenser, open the cartridge and place it upside down inside the plastic container. Alternatively,

soap can be poured directly into the plastic container. The dispenser has been designed for quick and easy reﬁlling process.

INSTALLATION:

After opening the dispenser cover, remove the plastic container, gently lifting it upwards while pressing the locking latch. Mount the

dispenser to the wall by using the enclosed screws and wall plugs. Make sure the wall surface is in good condition to ensure proper

mating of the dispenser to the wall. Use silicone or glue pads if necessary.

Note:

1. The dispenser should be installed near or directly above the sink to allow wet hands to drip into the sink.

2. Allow sufﬁcient space above dispenser to exchange cartridges easily.

3. Recommended installation height: 100 – 110 cm (39" - 43")(measured from ﬂoor to the bottom of the dispenser).

TECHNICAL SPECIFICATIONS:

Model B-26627 from Bobrick Washroom Equipment, Dispenser made of 0.8 mm thick, (22 gauge) 1.4301, Type CrNi 18/10, AISI 304

stainless steel with a brushed, satin ﬁnish; plastic container for soap cartridges (up to 500 ml), as well as for bulk reﬁll of soap (up to

500 ml); lockable with a Bobrick System lock; soap level indicator.

CARE INSTRUCTIONS:

Clean regularly with warm water and/or stainless steel cleaner.

Do not use acid (chloride) cleaners or scouring agents.

The suction valve can be cleansed by pumping hot water through it.

Do not dismantle the dispenser.

Use only original spare parts.

Foam Soap Bulk-Fill Dispenser shall be Model B-26627 of Bobrick Washroom Equipment, Inc., Clifton Park, New York;

Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick

Washroom Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.

B-26627

Summary of content (2 pages)

PAGE 1
Technical Data TrimLineSeriesTM Surface-Mounted Foam Soap Dispenser 500ml Drilling Specifications 65mm 96mm Lock & Key S B-26627 Finish Face of Wall 116mm Plastic Container 153mm S 297mm 260mm 217mm 108mm 310mm MATERIAL: Welded, 0.8mm (22 gauge) 1.
PAGE 2
Installation INSTRUCTIONS BOBRICK Surface-Mounted Foam Soap BULK-FILL Dispenser 1. Install dispenser near or directly above sink to allow wet hands to drip into sink. 2. Allow sufficient space above dispenser to exchange cartridges or refill from bottle easily. 3. Recommended installation height: 100 – 110 cm (39" - 43") (measured from floor to bottom of dispenser). 4. For installation please follow instructions down below: 1. Mount dispenser to wall using enclosed screws and wall plugs. 2.