Installation Sheet
continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 4/23/21
R/B
Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2021 by Bobrick Washroom Equipment, Inc.
Technical Data
B-2906 Series Polished Stainless Steel Mirror —
60" x 63" (152 x 91cm) or
36" x 60" (91 x 152cm) maximum;
12" x 12" (30 x 30cm) minimum.
B-2908 Series Tempered Glass Mirror —
115" x 48" (292 x 122cm) or
48" x 115" (122 x 292cm) maximum;
18" x 30" (46 x 76cm) or
30" x 18" (76 x 46cm) minimum.
B-2909 Series Laminated Glass Mirror —
84" x 48" (213 x 122cm) or
48" x 84" (122 x 213cm) maximum
16" x 18" (41 x 46cm) or
18" x 16" (46 x 41cm) minimum.
B-2908 Series Tempered Glass Mirror
Standard Sizes —
B-2908 1830 18" x 30" (46 x 76cm)
B-2908 1836 18" x 36" (49 x 91cm)
B-2908 2436 24" x 36" (61 x 91cm)
MATERIALS:
Frame — 18-8, Type-304, heavy-gauge stainless steel, 3/4" x 3/4" (19 x 19mm) angle with vertical-grain satin finish. One-piece, roll-
formed construction forms continuous integral stiffener on all sides. Bevel design on front of angle holds frame tightly against mirror.
Corners are welded, ground, and polished smooth. Galvanized steel back is fastened to frame with concealed screws and equipped with
integral horizontal hanging brackets. Concealed Phillips-head locking screws securely fasten mirror to wall hanger(s).
SPECIAL-ORDER REFLECTIVE SURFACES Specify Series Required:
Designer's Notes:
1. Special-order sizes available on request.
2. Maximum size one-piece angle-frame mirror, 144'' x 52'' (366 x 132cm); minimum size, 12'' x 12'' (30 x 30cm).
3. All Bobrick framed mirrors are manufactured to overall width and height dimensions. EXAMPLE: A 24'' x 36'' (61 x 91cm)
mirror will be furnished 24'' x 36'' (61 x 91cm) outside-of-frame to outside-of-frame.
4. To specify special sizes use Series Number followed by width then height in inches. EXAMPLE: B-290 2024.
5. Bobrick framed mirrors are manufactured to a tolerance ± 1/8'' (3.2mm).
6. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4'' (85mm) for Snap Locking Design; 5-3/8" (137mm) for
"2S" Tab Design minimum clearance above center line of mounting screw holes.
7. Provide 1'' (25mm) minimum clearance at bottom of mirror for unlocking mirror from wall and 1/2'' (12.7mm) clearance on
each side.
MIRROR WITH
STAINLESS STEEL
ANGLE FRAME
B-2906
B-2908
B-2909
Figure: 1
Figure: 2
SNAP LOCKING DESIGN
(Rear View)
"2S" Tab Design
(Rear View)
- for all other mirrors up to a width of 36"
2-1/2''
65mm
S
3/4''
19mm
Side View
Back Plate/Wall Hanger
2-9/16''
65mm
S
4'' or 5" Typ.
100 or 125mm
S
T
2-7/16''
60mm
S
1-15/16''
45mm
S
3"
75mm
S
Locking Screw
(Phillips-Head)
Frame
Mirror
Note: Mirrors greater than 36" in width will have multiple
hanger brackets with a typical 8" o each edge.
Mirror
Frame
Finish Face
of Wall
3/4''
19mm
Mirror
Bracket
Mirror
Bracket
w/Tape
(Does not engage with lower Louvers)
S
4"
100mm
Typ.
S
Half
Mirror Width
S
2-7/8"
75mm
S
1" to 1-1/2"
25mm to 40mm