Specification Sheet

continued . . .
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 9/11/17
R/B
Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2017 by Bobrick Washroom Equipment, Inc.
Technical Data
MIRROR WITH
STAINLESS STEEL
ANGLE FRAME
B-2906
B-2908
B-2909
Designer's Notes:
1. Special-order only.
2. All Bobrick framed mirrors are manufactured to overall width and height dimensions. EXAMPLE: A 24" x 36" (61 x 91cm) mirror will be furnished 24" x 36"
(610 x 915mm) outside-of-frame to outside-of-frame.
3. To specify sizes use Series Number followed by width then height in inches. EXAMPLE: B-2906 2024.
4. Bobrick framed mirrors are manufactured to a tolerance ±1/8" (3.2mm).
5. For sufficient space to lift mirror onto wall hanger(s), provide 3-1/4" (85mm) minimum clearance above center line of mounting screw holes.
6. Provide 1" (25mm) minimum clearance at bottom of mirror for engaging locking screws and 1" (25mm) clearance on each side.
 B-2906 Series Polished Stainless Steel
Mirror —
60" x 63" (152 x 91cm) or
36" x 60" (91 x 152cm) maximum;
12" x 12" (30 x 30cm) minimum.
 B-2908 Series Tempered Glass Mirror —
115" x 48" (292 x 122cm) or
48" x 155" (122 x 292cm) maximum;
18" x 30" (46 x 76cm) or
30" x 18" (76 x 46cm) minimum.
 B-2909 Series Laminated Glass Mirror —
84" x 48" (213 x 122cm) or
48" x 84" (122 x 213cm) maximum
16" x 18" (41 x 46cm) or
18" x 16" (46 x 41cm) minimum.
 B-2908 Series Tempered Glass Mirror
Standard Sizes —
B-2908 1830 18" x 30" (46 x 76cm)
B-2908 1836 18" x 36" (49 x 91cm)
B-2908 2436 24" x 36" (61 x 91cm)
SPECIAL-ORDER REFLECTIVE SURFACES
Specify Series Required:
2-1/2''
65mm
S
3/4''
19mm
Side View
Back Plate/Wall Hanger
2-9/16''
65mm
S
4'' or 5" Typ.
100 or 125mm
S
T
2-7/16''
60mm
S
1-15/16''
45mm
S
3"
75mm
S
Locking Screw
(Phillips-Head)
Frame
Mirror
SNAP LOCKING DESIGN
(Rear View)
LOCK TAB DESIGN
(Rear View)
Figure: 1 Figure: 2
Slide flat-blade screwdriver
or Key between Mirror and
Wall. Depress Tab on back
Panel and remove Mirror.
Contact factory for key.
Lock Tab
4-5/8"
117mm
3-1/8"
79mm
Wall
Bracket
Lock
Tab
Mirror
Key
Half
Mirror Width
Frame
Mirror
S
S
Finish Face of Wall
3/4''
19mm
Width
Hanger Pockets
Up to 30'' (76cm) 1
Over 30" up to 72" (76 to 183cm) 2
Over 72" up to 108" (183 to 274cm) 3
Over 108" (274cm) 4
Note: Mirrors greater than 30" in width will have multiple
hanger brackets with a typical 8" off each edge.