Installation Sheet

O-Ring
Round
Cap
Reconnect Tube to
Retainer Barb
Retainer
Back
Engage Hook from
Retainer Back
into Retainer
Retainer
Screw Hole
Duckbill
Valve
Part No.
822-35
O-Ring
Part No.
830-45
1. Place Counter Gasket
over mounting hole to
align with profile of
dispenser.
2. Insert Shank with tube
and all Fiber Optic Cables
carefully through mounting
hole.
3. Install Wave Washer on
Shank from below counter.
NOTE: Make sure Fiber Optic
Cables are INSIDE Wave
Washer.
4. Install Mounting Nut on
Shank and screw on to
Shank. [Minimum 2-1/4"
(55mm) diameter
clearance needed below
the counter for the
mounting nut].
NOTE: Make sure Fiber Optic
Cables are INSIDE Mounting
Nut. Do not tighten completely
until the end of installation.
6. Insert tube from the
Top Assembly with Spout
and Shank onto Retainer
Back with Bottle Cap
remaining above.
NOTE: Do not use any tools
to assemble tubing onto
barbs. Lubricate tube end
or barb with soap to ease
assembly.
7. Place Retainer Back into
grooves of Shank.
Ensure Duckbill valve is
inserted on the bottom
of the Retainer barb and
O-Ring is in place.
8. Connect and rotate
Retainer Back to Back
Retainer. Ensure Fiber
Optic Cables are on the
outside of the Retainer
Back.
9. Insert screw and tighten
retainers together.
12. On the bottom ot the
Retainer, place Rubber
QC Gasket, Stainless
Steel Washer and
Rubber QC Gasket.
NOTE: Ensure big hole
and little hole are aligned
properly with Retainer
prongs.
13. Insert Bottle with
Gasket, Washer, and
Gasket to the Adapter
ensuring prongs go in
appropriate holes in the
bottle.
NOTE: Ensure O-ring is
seated in the Adapter.
12. Slide Bottle Cap down
over Bottle threads and
tighten clockwise. and
then turn an additional
3/4" turn to seal
connection.
CAUTION: DO NOT bend or
kink Fiber Optic Cables
13. Insert Fiber Optic
Connector Tip into
Bottom Housing. Keyed
feature on Connector
Tip ensures Fiber Optic
Cables are always
located correctly.
15. Place Fiber Optic cable
cover over loose fiber
optics to conceal.
NOTE: DO NOT bend or
kink Fiber Optic Cables.
17. Mount Battery Pack on
wall nearest dispenser.
Mounting hardware is
inside the Battery Pack.
* Round Cap on plug is
not required for this
model, pull back prior to
plugging into port.
19. Plug Power Supply into
bottom housing base.
Installation:
18. Install 4 “D” cell Alkaline
batteries.
14. Thread Fiber Optic Nut
onto Connector Port and
tighten completely.
Filling Instructions: (use liquid soap only)
Unit will dispense Bulk Liquid Soap within a viscosity range of 100 to 19,000 cP.
1. Insert tip of BobKey provided into opening of concealed locking mechanism to disengage door.
2. Door will disengage and rotate clockwise for filling from the top.
3. Fill dispenser with commercially marketed bulk liquid hand soap (Do not use foam liquid or lotion soap).
4. Close door counter-clockwise to lock in place.
Replacement Parts List
Part Name Part No.
- Top Housing Assembly Liquid 824-325
- Bottom Housing Assembly Liquid 824-350
- A/C Adapter 3974-57
- International Assortment Plugs
(U. K., Europe, Australia) 3974-58
- D Size Battery Pack (Batteries not included) 824-241
- Nozzle Tip Replacement Kit Liquid 824-210
- Installation Hardware Packet 824-343
TOP FILL ONLY !
16. Ensure Mounting Nut is
tightened against
bottom of counter. Make
sure Fiber Optic Cables
are not between the
underside of the counter
and top of Mounting
Nut. See Steps 3 and 4.
5. Place Bottle Cap over
Shank. Ensure Fiber
Optic Cables are on the
outside of the Bottle Cap
and tubing is inside Bottle
Cap.
3
2