Installation Sheet

Coupling Tee
922-1
BobKey
24-17
Plug 922-10 and
O-Ring 922-11
Mounting Screws
(not furnished)
ABS End-Caps
(set of 2) for 3" (75mm)
standard pipe
in U.S.A. and Canada
(optional)
922-45
Pipe Connections
(not furnished)
Black Flexible Hose
922-20
Clear Elbow
922-2
Soap Pump Assembly
(includes Escutcheon, Piston,
Spout, Valve, and Supply Tube)
4'' Spout 6'' Spout
922-619 9226-619
Universal Mounting Group
(includes Plastic & Rubber Washers, Shank,
Spring Washer, and Retaining Nut)
822-402
HOW TO REFILL THE SOAP RESERVOIR:
1. On any one of the soap dispensers, turn the escutcheon clockwise slightly until it stops.
2. Insert the longest projection at end of BobKey into the rectangular hole of escutcheon; push straight in.
While holding BobKey in, turn cover counterclockwise about 1/8 turn. CAUTION: Do not use BobKey to
turn escutcheon.
3. Lift out the soap pump assembly enough to allow access to the entire shank opening for top filling. Lay
the soap pump assembly conveniently aside on the lavatory or countertop while filling system; the
supply tube can be left inserted in the shank.
4. Fill soap reservoir with soap. Watch the soap level in one of the clear elbows while filling. Do not over fill.
Use commercially marketed all purpose hand soaps.
Designer's Note: Bobrick liquid soap dispensers are designed to dispense commercially marketed all purpose hand soaps including liquid and lotion
soaps, synthetic detergents. Bobrick soap dispensers are NOT designed to dispense alcohol-based hand sanitizers or iodine-based surgical soaps.
Note: An average system with three soap dispensers 30" (760mm) apart and a total pipe length of 7½ ft. (229cm) will have a capacity of
approximately 3.0 gal. (11.4 L).
5. Replace soap pump assembly. Secure the escutcheon by turning it clockwise until lock snaps into position.
MAINTENANCE:
1. Never use abrasive cleaners on the soap dispensers.
2. The soap pump assembly should be removed from system and flushed by pumping warm water through it every six months.
3. At least once a year, flush the soap reservoir with warm water. Drain the system by removing the threaded plugs from the clear elbows.
CAUTION: Do not use solvents that could damage the ABS pipes.
REPLACEMENT PARTS LIST
RETROFIT KIT FOR BOBRICK B-822
SERIES LAVATORY-MOUNTED
SOAP DISPENSERS
Part No. 922-50 Retrofit Kit includes
coupling tee, clear elbow, black flexible
hose, supply tube, and plastic tie.
HOW TO INSTALL RETROFIT KIT:
1. Remove plastic soap container and
container cap from existing B-822 Series
lavatory-mounted soap dispenser.
2. Remove existing plastic tie and supply
tube from the soap pump assembly of
soap dispenser, then replace with those
supplied with Retrofit Kit.
3. Follow instructions on reverse side of
this document to complete installation of
soap reservoir system.
Soap Dispenser (includes Soap Pump Assem-
bly, and Universal Mounting Group)
4'' 100mm) Spout 6'' (150mm) Spout
922-405 9226-405
© 2016 by Bobrick Washroom Equipment, Inc.
Form No. 922-469 Revised 12/16/16 Printed in U.S.A.
BobKey
Escutcheon
Hole
In the U.S.A.: BOBRICK WASHROOM EQUIPMENT, INC.
Los Angeles: 6901 Tujunga Ave., North Hollywood, CA 91605-6213: Tel: [phone], FAX: [phone]
New York: 200 Commerce Drive, Clifton Park, NY 12065-1350; Tel: [phone], FAX: [phone],
or e-mail: [e-mail]
In Canada: BOBRICK WASHROOM EQUIPMENT COMPANY
45 Rolark Drive, Scarborough, Ontario M1R 3B1 • Eastern Canada: Tel: [phone] • FAX: [phone]
• Western Canada: Tel: [phone] • FAX: [phone]