UPRIGHT DISPLAY COOLER BRAND: BODEGA MODEL: SS-P360WD
SAFETY PRECAUTIONS ...........................................................................................................................................3 INSTALLATION ............................................................................................................................................................9 INSTALL AND ADJUSTABLE SHELF ...................................................................................................................15 OPERATION ........................
UPRIGHT DISPLAY COOLER 2
SAFETY PRECAUTIONS This manual contains the product’s basic knowledge, use instruction, fault diagnosis and basic trouble shooting methods. In order to better understand and use this product, please take good care of this manual and read it carefully. The purpose of the safety precautions in this manual is to ensure safe and correct use of the unit to minimize risks that could cause serious damage and injury. These safety precautions are divided into WARNINGS and CAUTIONS.
prevent damage to the refrigerator and personal injury. The appliance shall be disconnected from its power source during cleaning or maintenance and when replacing parts. When the cooler will be not be used for a long time, disconnect the power and clean it. Please examine the circuit before reuse.. DO NOT store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any other appliance.
The symbol is a warning and indicates the refrigerant and insulation blowing gas are flammable. Warning - Risk of fire / flammable materials. Warning - Do not store explosive substances such as aerosol cans with a flammable propellant in the unit. Warning - Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance Warning - The refrigerant and insulation blowing gas are flammable. When disposing of the appliance, do so only at an authorized waste disposal centre.
Precautions for Use All repairs, disassembly and modifications should be performed only by qualified technicians. Attempting to perform these yourself could result in a fire, malfunction, and injury. Never splash water directly onto the product or wash with water as shortcircuit and electrical leakage could result. Never put flammable or volatile substances into the unit as explosion and fire could result. Do not damage, modify, excessively bend, strain, twist or bundle up the power cord.
Install the unit in a location where the floor is sturdy enough to support the load of the unit. If the floor is not sturdy enough or installation is incorrectly performed, the unit could tip over and falling shelves and products could cause personal injury. If you find gas leakage,please don't touch the appliance. Turn it off and open the doors and windows for ventilation.Gas leakage could cause explosion, fire, and fire injury.
Grasp the handle when closing the door. Holding at other positions could result in pinched fingers and injury. Do not push hand against or apply excessive force to glass surfaces as the glass could break and cause injury. When disconnecting the power cord plug from the wall outlet, hold at the plug main body close to the outlet. Pulling the cord could cause wire breakage, possibly resulting in overheating and fire. Make sure that the unit does not tip over or fall when it is moved.
INTRODUCTION The Merchandising Refrigerators are essential for the display and sale of packaged goods. This makes them invaluable for a variety of commercial businesses, including convenience stores, offices, supermarkets, restaurant, bar, hotel and any other place where grab-and-go food and beverage options are readily available. The Display Coolers are attractive, eye-catching display refrigerators and designed to store, cool and display bottled or canned beverages.
Technical Specifications Model SS-P360WD RATED VOLTAGE 115V~ RATED FREQUENCY 60Hz Dimensions(L*W*H) TOTAL CAPACITY D2.2 ft³ 1 RATED INPUT POWER 165W DATED CURRENT R D.7A 1 HIGH PRESSURE 320Psig DOW PRESSURE L D30Psig 1 REFRIGERANT R600a(0.12 Ibs) DNERGY CONSUMPTION E D.
465mm/18.3inch 436mm/17.2inch 30 bottle 30 bottle 30 bottle 30 bottle This model can store about 11 120 standard bottles.
84 bottle 84 bottle 84 bottle 84 bottle 84 bottle This model can store about 420 standard bottles. TIP: You can change the height of the shelf according to your needs. This will reduce the stated bottle capacity. INSTALLATION Guides to Choose Location 1. The unit is for indoor application only. Outdoor use may cause decreased efficiency and a damage to the unit. 2. Due to the fact that the unit has a glass door, its performance is highly influenced by environmental conditions.
When positioning the appliance, maintain a distance of 10 cm (4 inches) between the appliance and walls or other objects for ventilation and ease of use. Keep all ventilation openings in the appliance enclosure or in the structure clear of obstruction. In order to reduce fire hazard, the installation of this appliance must be carried out only by a suitably qualified person. Position the appliance in such a way that the plug is accessible at all times. Openings & Plan Views 57 1978mm/77.
Electrical Safety Be sure to follow the National Electrical Code, as well as local codes and ordinances, when installing the receptacle. Before your new unit is connected to a power supply, check the incoming voltage. Please refer to the electrical requirements on the unit’s nameplate. Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service technician install an outlet near the appliance.
INSTALL AND ADJUSTABLE SHELF Shelf height adjustment. The shelf height can be adjusted. Arrange the shelves in accordance with the dimensions of the items to be placed in the cooler. How to Install the Fixer of Shelf Step 1 Put on the shelf. Step 2 Insert the bottom of a fixer to the hole for the height that you need.
How to Discharge the Fixer of Shelf Step 1 When discharge the fixer, push the fixer Step 2 Take the other side off the hole to one side and let another side gets away from the hole How to Install the K-Type Fixer of Shelf Step 1 Take out k-clip and align with hole. Step 2 Insert the 2 side into hole at the same time.
OPERATION Before Use Remove shipping package, tape, etc, and leave doors open to ventilate for a while. The unit is cleaned before shipment. However, clean the compartment interior using warm water then dry it with a soft-cloth after delivery, for the glass parts only use specific products, avoiding the use of water which can leave on the glass residues. Allow the unit to run for about 1 hour to cool before placing items in the cooler.
NOTE: This machine has an internal temperature differential that works as a protection for the compressor. The way the differential works is that at whatever temperature the unit will be set at, the compressor will work and cool the cabinet down until it reaches the chosen set point then it will shut itself up. It will allow a differential of 4 degrees before starting its operation back. The reason is to protect the compressor from doing short cycles (on / off) repetitively.
MAINTENANCE & CLEANING The smooth operation and life of the equipment are mainly determined by correct and regular maintenance. It is much easier to clean on a regular basis than to have to remove stains once they have built up. Cleaning WARNING To prevent any electrical shock hazards or injury by rotating circulation fan, always disconnect the power cord plug from the wall outlet before cleaning.
Periodically remove the shelves from the unit, and clean them with a mild soap and warm water. Rinse under tap afterwards to remove any soap residues. NOTE: Always dry the shelves before placing them back inside the chamber. To ensure the safety, perform the following checks after cleaning. 1. Is the power cord plug firmly inserted into a dedicated wall outlet? Confirm that the plug is not abnormally hot. 2. Check the power cord for cracks and damage.
TROUBLE SHOOTING Fault Cause Resolution 1.Manual temperature Open traverse or bad connection Check wires to ensure a good connection controller dis-function/flicker Have a fault on indicator Change the electronic controller Open traverse or bad connection Check wires to ensure good connection 2.
PROCEDURES OF REPLACING PARTS Change Air Fan Step 1 Step 2 Step 3 Remove screws on the fan board, put the whole board down slowly, and disconnect the wire. Remove these 4 screws and take off the fan cover. Remove the screws of the sensor, take off it and the fixed clip. Step 5 Hold up fan board slowly to connect fan wires, collect wire units and tighten fan board.
23
