TR1120 OWNER’S MANUAL IMPORTANT： For maximum effectiveness and safety, please read this owner’s manual before using your BodyCraft treadmill. Retain this owner’s manual for future reference.
1. It is the responsibility of the owner to be sure that all users of this treadmill are informed of all warnings and precautions. 2. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, outdoors or near water. 3. Keep pets and small children away from the treadmill at all times. 4. Never start the treadmill while you are standing on the walking belt. 5. Always hold the handrails while using the treadmill. 6. The treadmill is capable of high speeds.
12. Remove the safety key and store it away in a safe place when the treadmill is not in use. Keep the safety key away from children. 13. Wear the proper exercise clothing and shoes for your workout. Do not wear loose clothing or shoes with leather soles or heels. Be sure to tie long hair back. 14. Keep all loose clothing and towels away from running surface. The belt will not stop immediately if an object becomes caught in the rollers or belt. Should an object become caught, turn the unit off immediately.
STEP 1 Do not move the treadmill out of the box until unit is assembled. Collapse box bottom and lay sides down before assembly.
STEP 2 Lift up the upright handlebar, then fasten the screws (C) and washer (D, E) tightly at the bottom of the upright handlebar.
STEP 3 1. Attach the console to the upright by pressing both handlebars down. Place the washers (D) and screws (C) on the handlebar as shown in Figure 3. 2. Place 2 Bottle Holders into left and right consoles.
STEP 4 Attach upright side cap (B) with screws (D) at the bottom of the upright handlebar, and tighten them well.
FOLDING After assembly is complete, you may fold the machine into the upright position for storage. To fold the machine, raise the deck and turn the knob until it locks into position. NOTE! Make sure you hear the click sound of the deck locking into position. This is to ensure the deck is locked in place and will not drop back down. NOTE! Make sure the treadmill’s elevation is at lowest position before folding the deck. If the elevation is not at lowest position, folding will damage the mechanism.
*** THE TREADMILL CIRCUIT BREAKER WILL SHUT OFF POWER WHEN THE ELECTRIC CURRENT IS OVERLOADED. A. Pull out the plug from the electrical socket on the front of the treadmill. B. Push in the circuit breaker switch. C. Insert the plug back into the electrical socket. Note：Do not push in the circuit breaker switch before you pull out the plug from the treadmill.
NOTICE : The treadmill should be placed on a level surface. If the treadmill is not level, the belt will continuously track to low side of the treadmill. WALKING BELT TENSION As walking belts tend to stretch slightly with use, the belt may occasionally need to be tightened. If belt is too loose, you may find the belt stops while running or walking, while the motor continues to run. DO NOT OVERTIGHTEN THE BELT. This will cause reduced motor performance and roller damage.
WALKING BELT CENTERING The walking belt may occasionally need to be centered. First be certain that the belt is tensioned properly. Start the treadmill and run it at about 4 mph. Place the hex key through the hole in the left rear end cap and into the socket of the adjustment screw. (See picture below) 1. If belt has moved too far to the right: Turn the left adjustment screw ½ turn counter clockwise. Let the treadmill run for 30 seconds and the belt should move to the left.
WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET BEFORE CLEANING, LUBRICATING OR SERVICING THE UNIT. CLEANING General cleaning of the treadmill will prolong its life and improve performance. Keep the unit clean by dusting regularly. Be sure to dust the exposed part of the deck on either side of the walking belt and also the side rails. For best performance, we recommend your treadmill be placed on a treadmill mat.
BEFORE STARTING Straddle the belt and stand on the plastic side rails. Place the safety key onto the circle on the overlay and attach the rope to your clothing. Do not stand on the walking belt while starting or stopping the treadmill. If you are a new user, stay at a slow speed and hold onto the handrails until you become comfortable. KEY FUNCTIONS Safety Key: The monitor can be operated only with the key attached to the treadmill. The monitor shuts off and the treadmill stops when this key is removed.
SPEED +: Increases the speed. Pressing once increases the speed 0.1 mph. Pressing and holding for two seconds will increase the speed faster. This button is also used to scroll the programs. SPEED -: Decreases the speed. Pressing once decreases the speed 0.1 mph. Pressing and holding for two seconds will decrease the speed faster. This button is also used to scroll the programs. SPEED HOT KEYS 2/4/6 MPH: Change the speed to the selected speed.
OPERATION INSTRUCTION (PLEASE READ CAREFULLY BEFORE USING): BEFORE STARTING Straddle the belt and stand on the plastic side rail. Place the Safety Key onto the circle on the overlay and attach the rope to your clothing. Do not stand on the walking belt while starting or stopping the treadmill. If you are a new user, stay at a slow speed and hole on to the handrail until you become comfortable.
P1 Manual Program: Press ENTER button to enter this program. SPEED window will flash. Use INCLINE + - or SPEED + - to set the desired speed. Press ENTER. TIME window will flash. Use INCLINE + - or SPEED + - to set up the desired time. Press ENTER. DISTANCE window will flash. Use INCLINE + - or SPEED + - to set up the desired distance. Press ENTER. CALORIES window will flash. Use INCLINE + - or SPEED + - to set the number of calories to be burned. Press ENTER. Press START to begin exercise.
Engineering Mode With power ON position, press and hold “SPEED –“ button then press “INCLINE +” button to enter the Engineer Mode. PULSE window shows software version. INCLINE window shows year. TIME window shows date. DISTANCE window shows diameter of roller. SPEED window shows “st” for Metric and “En” for Imperial. Press ENTER button to enter KM/MILE switch mode, Press SPEED + - or INCLINE + - to select “0” for KM or “1” for MILE. Press ENTER button, window shows total distance.
17
18
19
20
21
22
] 23
24
25
