BRM 3671 /3681/3690 For use under U.S. Patent numbers 6159132, D459773, D438264 * This item is for consumer use only and it is not meant for commercial use.
This page intentionally left blank
General Information Safety Before you undertake any exercise program, please be sure to consult with your doctor. Frequent strenuous exercise should be approved by your doctor and proper use of your product is essential. Excessive or incorrect training may result to health injuries. Please read this manual carefully before commencing the assembly of your product or starting to exercise. • Please keep all children away from this item when in use.
Hardware & Tool List The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these items. PLEASE NOTE: some of these parts may have already been pre-assembled on your unit. Bolts #2. Bolt (M8 x 15 mm) [2 pieces] #38. Bolt (M8x20 mm) [4 pieces] #12. Bolt (M8x45 mm) [4 pieces] #18. Left / Right Pedal Bolt [2 pieces] #63. Screw (M4 x 10 mm) [4 pieces] #65. Bolt (M8x30 mm) [2 pieces] #27. Carriage Bolt (M8x73 mm) [4 pieces] Pre-assemble Washers #4.
Parts Listing The following parts list describes all of the parts illustrated on the exploded diagram on the following page. Please note, most of these parts are already pre-assembled on your unit. Part # Description 1......................Handle Bar Foam Grip Part # Description 37....................Arc-Washer (for M8 bolt) 2......................Bolt (M8 x 15 mm) 38....................Bolt (M8x20 mm) 3......................Bolt Cap (for M8 bolt) 39....................Spring Loaded Knob 4......
Exploded Diagram The following diagram is provided to help you familiarize yourself with the parts and hardware that will be used during the assembly process. Please note that not all of the parts and hardware you see here will be used while you are assembling the machine because some of these items are already pre-installed. Please continue to the next page to begin the assembly process and use this page only as a reference guide for parts and hardware.
Assembly Instructions Assembly Step 1 Hardware Required FRONT STABILIZER ASSEMBLY Secure the Front Stabilizer (#69) to the Main Frame (#48) using a total of two Carriage Bolts (#27) two Arc-Washers (#37) and two Cap Nuts (#49). #27. Carriage Bolt (M8x73 mm) [4 pieces] #37. Arc-Washer [4 pieces] REAR STABILIZER ASSEMBLY Secure the Rear Stabilizer (#26) to the Main Frame (#48) using a total of two Carriage Bolts (#27) two Arc-Washers (#37) and two Cap Nuts (#49). #49.
Assembly Instructions Hardware Required Assembly Step 2 WIRE CONNECTIONS Connect the Main Sensor Wire [middle] (#54) to the Main Sensor Wire [lower] (#67). #38. Bolt (M8x20 mm) [4 pieces] CENTER POST ASSEMBLY Slide the Center Post (#58) onto the Main Frame (#48) and secure it using a total of four Arc-Washers (#37) and four Bolts (#38). #37. Arc-Washer [4 pieces] Tools Required 55 40 1 2 3 55 Make sure this wire is hanging out before assembling the Center post (#58).
Assembly Instructions Assembly Step 3 Coupler Bar Assembly Slide two Spacers (#31) onto the two bars that are protruding from the Center Post (#58). Then slide one Left Pedal Bolt (#18L) into the Pedal Connection Joint (#20). Assemble the Coupler Bar (#8L) to the left side of the unit by sliding the upper part onto the left bar that is protruding from the Center Post (#58). Secure it using one Washer (#5), one Spring Washer (#4), one Bolt (#2) and then place a Bolt Cap (#3) on top of the Bolt (#2).
Assembly Instructions Assembly Step 4 Assembly Step 5 HANDLE BAR ASSEMBLY PULSE HANDLE BAR ASSEMBLY Insert the two Handle Bars (#29L & 29R) into the openings at the end of the two Coupler Bars (#8L & #8R). Secure the Handle Bars (#29) using two Knob Bolts (#7). Place two Bolt Caps (#3) on the welded nuts located on the opposite side of the Knob Bolts (#7). Install the Pulse Handle Bar (#70) onto the front side of the Center Post (#58) using two Bolts (#65) and two Spring Washers (#4).
Assembly Instructions Assembly Step 6 Hardware Required Seat Assembly Remove the Washers and Nuts that are pre-assembled on the back of the Seat (#33) and set them aside as they will be used in later in this process. Attach the Seat (#33) onto the Horizontal Seat Bar (#35), ensuring that it is pointing directly toward the short end of it and then tighten with three Washers (#73) #42 WASHER FOR M10 BOLT,T2.0 1PC and three Nylon Nuts (#72) that were previously removed.
Assembly Instructions Assembly Step 7 PEDAL ASSEMBLY Attach the two Pedals (#13) as shown using a total of four Bolts (#12), four Washers (#73) and four Nylon Nuts (#72). The pedals are marked with "L" or "R". Make sure the pedals are positioned as shown otherwise they will not fit properly. If the pedals do not fit, make sure that you installed the Spacer (#31) correctly during step number 3. Hardware / Tool Required #12. Bolt (M8x45 mm) #73.
Safety & Maintenance SAFETY & WARNINGS • Make sure all nuts, bolts, and screws are tightened prior to use. • Be sure that all adjustment locking devices and safety devices are properly engaged prior to use! • Never over-tighten the above-mentioned devices and parts to avoid damage to the unit. • Check for loose parts and components and make proper adjustments prior to use. • Check to see if there are any tears or bends in the welding or metal prior to use.
Computer Operation I. To operate the monitor A-0. Plug in the AC Adapter to power supply. You will see this first screen followed by the next one. A-1. You may select different training mode of MANUAL, PROGRAM, USER or TARGET H.R. by pressing UP, DOWN buttons (a1). Press MODE button to confirm. Or, you may press ST/STOP button to start training directly in MANUAL mode. A-2. In a fresh monitor, if you start the selected mode, all function data start counting up from zero once the training starts (a2).
Computer Operation B-6 During all training period, you may press ST/STOP to stop monitor counting at anytime. C. Training in PROGRAM mode - press UP button until PROGRAM shows up on the upper line, press MODE to confirm. M (c1) M (c2) M M (c3) (c4) C-1 The initial set program profile is P1 (c1 & c2). There are 12 training program profiles (P1-P12) available. You may press UP/DOWN button to select the desired training profile. Press MODE button to confirm.
Computer Operation left-upper corner) and beep for 8 times to remind you.(d6) D-5 You may press ST/STOP button to start training again. The function which has achieved to zero will start from previous set data counting down, and other set function data will keep counting up or down from previous records. D-6 During all training period, you may press ST/STOP to stop monitor counting at anytime. E. Training in TARGET H.R. mode - press UP button until TARGET H.R.
Computer Operation RPM TIME DISTANCE CALORIES PULSE* RECOVERY WATT Displays current training rotations per minute. Count up - If NO preset target, Time will count up from 00:00 to maximum 99:59 with each increment of 1 second. Count down - If training with preset Time, Time will count down from preset value to 00:00.Each preset increment or decrement of 1 minute between 1:00 to 99:00. Count up - If NO preset target, Distance will count up from 0.00 to maximum 99.90 with each increment 0.1 Mile.
Troubleshooting (AFTER COMPLETE ASSEMBLY) Troubleshoot Area HAND PULSE SIGNAL CALORIES/DISTANCE/ TIME/(ETC.) COMPUTER Display Solution If the computer is not picking up your hand pulse signal (or you are getting inaccurate readings), please adjust the following: 1. Slightly moisten/dampen the palms with water so the sensors can detect a pulse signal. 2. Do not grip the sensors too tightly. Only moderate pressure need be applied.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE USE & REFERENCE. DO NOT DISCARD. WARNING: SERIOUS INJURIES AND EVEN DEATH CAN OCCUR IF THE PROPER SAFETY PRECAUTIONS ARE NOT FOLLOWED. The diagram below highlights and reviews many of the important Safety and Warning labels also found on the unit. Please ensure any user of the unit familiarizes themselves with these Safety and Warning guidelines before use.
Proof of purchase Model Number BRM 3671/3681/3690 version: 08-27-2012 BRM3671/3681/3690
