User Manual

ManualsBrandsBodyMedia ManualsElectronicsSenseWear (R) biotransceiver

7 8

Important Information About the SenseWear

biotransceiver

3 Vrms

150 kHz to 80 M Hz

3 V/m

80 M Hz to 2.5 GHz

N/A

3 V/m

Portable and mobile communications equipment

should be separated from BT-2.4-BP by no less

than the distances calculated/ listed below:

D=(3.5/V1)(Sqrt P)

D=(3.5/E1)(Sqrt P) 80 to 800 MHz

D=(7/ EI)(Sqrt P) 800 MHz to 2.5 GHz

where P is the max power in watts and D is the

recommended separation distance in meters.

FIeld strengths from ﬁ xed transmitters, as

determined by an electromagnetic site survey,

should be less than the compliance level in each

frequency range

Interference may occur in the vicinity of equip-

ment containing a transmitter symbol:

•

Conducted RF

IEC 61000-4-6

Radiated RF

IEC 61000-4-3

The BT-2.4-BP (SenseWear

biotransceiver) is intended for use in the electromagnetic environment speciﬁ ed below.

The customer or user of the BT-2.4-BP should ensure that it is used in such an environment.

Guidance and Manufacturer’s Declaration - Emissions

IEC 60601

Test Level

Compliance

Level

Electromagnetic

Environment - Guidance

Immunity Test

NOTE 1 At 80 M Hz and 800 M Hz, the higher frequency range applies

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and

reﬂ ection from structures, objects and people

100 11.6666 11.6666 23.3333

10 3.6893 3.6893 7.3786

1 1.1666 1.1666 2.3333

Important Information About the SenseWear

biotransceiver

0.1 0.3689 0.3689 0.7378

The BT-2.4-BP (SenseWear

biotransceiver) is intended for use in the electromagnetic environment in which radiated

disturbances are controlled. The customer or user of the BT-2.4-BP can help prevent electromagnetic interference by

maintaining a minimum distance between portable and mobile RF Communications Equipment and the BT-2.4-BP as

recommended below, according to the maximum output power of the communications equipment.

Recommended Separations Distances for the BT-2.4-BP

0.01 0.1166 0.1166 0.2333

Separation (m)

150kHz to 80MHz

D= (3.5/V1)(Sqrt P)

Separation (m)

80 to 800MHz

D= (3.5/V1)(Sqrt P)

Separation (m)

800MHz to 2.5GHz

D= (7/E1)(Sqrt P)

Max Output Power

(Watts)

Field strenghts from ﬁ xed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios,

amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess

the electromagnetic environment due to ﬁ xed RF transmitters, and electromagnetic site survey should be considered. If the

measured ﬁ eld strength in the location in which the BT-2.4-BP is used exceeds the applicable RF compliance level above, the

BT-2.4-BP should be observed to verify normal operation. If abnormal performance is observed, additional measures may be

necessary, such as re-orienting or relocationg the BT-2.4-BP.

Over the frequency range 150 kHz to 80 MHz, ﬁ eld strengths should be less than 3 V/m.

For transmitters rated at a maximum output power not listed above, the recommended seperation distance d in meters (m)

can be determined using the equation applicable to the frequency of the transmitter, where P is the maximum output pow er

rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1 At 80 M Hz and 800 M Hz, the seperation distance for the higher frequency range applies.

NOTE 2 These guideleines may not apply in all situations. Electromagnetic propogation is affected by absorption and

reﬂ ection from structures, objects and people.