TM-2030 Installation & User Guide

ManualsBrandsBogart Engineering ManualsWind and Solar EnergyBogart Engineering BMS-TM-RV-100 Battery Management System With TM-2030RV, SC-2030 & 100A Shunt

Warranty:Allitemshavea3yearlimitedwarrantycoveringanyitemthatdoesnotperform

accordingtospeciﬁcaonsstatedorimpliedinourinstrucons,provideditdoesnotshow

obvioussignsofabuseormisapplicaon.Wewillreplaceorrepairanysuchitematourop-

on.AreturnauthorizaonisrequiredforallmerchandisereturnedtoBogartEngineering.

BogartEngineering2017

www.bogartengineering.com

AMPS

Hold SELECT 3

seconds to view

VOLTS

FULL

when flashing-meets "CHARGED" criteria

AMP-HOURS FROM "FULL"............RESET: to 0 Amp-hours

DAYS SINCE "CHARGED"................RESET: to 0 days

DAYS SINCE EQUALIZED................RESET: to 0 days

REPLACED PERCENTAGE FROM LAST DISCHARGE

=AMPS or =WATTS

SELECT

RESET

Operating and programming instructions at

www.bogartengineering.com/support

TM 2030-RV

Bogart Engineering

CHARGING

BATTERY

REMINDERS

=TIME TO CHARGE

FULL

=TIME TO EQUALIZE

=BATT. VOLTS LOW

TM-2030

TriMetric Battery Monitor

Installation and User Guide



Revised04/23/2017

Summary of content (8 pages)

PAGE 1
TM-2030 TriMetric Battery Monitor Installation and User Guide TM 2030-RV when flashing-meets "CHARGED" criteria Bogart Engineering CHARGING =TIME TO CHARGE FULL TO EQUALIZE =TIME SELECT AMPS RESET % FULL =BATT. VOLTS LOW BATTERY REMINDERS B1 VOLTS B2 Hold SELECT 3 seconds to view DAYS SINCE "CHARGED"................RESET: to 0 days AMP-HOURS FROM "FULL"............RESET: to 0 Amp-hours or =WATTS DAYS SINCE EQUALIZED................
PAGE 2
T riMetric Installation C H D B E A Negative from all loads and charging sources connect to shunt -Inverter -SC-2030 -Alternator -Chassis Ground Illustra on By R.
PAGE 3
Wire Length (feet) Wire Gauge Shunt Type Maximum Charging Amps 45 70 110 150 300 Over 300 # 26 # 24 # 22 # 20 # 18 CAT5 Refer to h p://www.nfpa.org for electrical wiring standards and informa on 500 Amp-50 mV (default) 100 Amp-100mV 1000 Amp-100mV “H” under P11 Set to “L” under P11 (rarely used) “H” under P11 400 75 650 TRIMETRIC INSTALLATION: Turn off main breaker to battery before attempting installation. Remove all connections from battery negative post. A. 4-Wire cable.
PAGE 4
Primary System Information IMPORTANT! After installation, the voltage set-point and amps set-point (P1 and P3) must be programmed in order to display % Full. Once programmed, a full charge must occur (parameters must be met) once before the % Full display will show a value. To Program the TriMetric: Press and hold Select until P1 appears, then press Select to toggle through the different programmable data (P1-P22). To change the data, briefly press Select and Reset at the same time and let go.
PAGE 5
Other Programmable Parameters P4: Choose either amps (“A”) or power (watts) (“Pr”) to appear in the primary display. Default “A” P5: Days since charged alarm set point (off, 0.0 to 250 days). Default “Off” P6: Days since equalized alarm set point (off, 0.0 to 250 days). Default “Off” P7: User “complexity” level. L1, L2 ,L3, or L4. Note: L3 or L4 is required to access P8-P22 program parameters.
PAGE 6
Advanced Programmable Parameters Programming Instructions for the TM-2030: http://www.bogartengineering.com/wp-content/uploads/docs/EnterP1Data.pdf Refer to SC-2030 instructions for programmable parameters when using the SC-2030 Solar Charger (P8-P14-P15-P16-P20-P21-P22) P8-P22 are accessible only when Program P7 is set to L3 or L4. Default values shown below are automatically installed when switching from L4 or L3 into L2 or L1. P9: Lo-battery audible alarm: based on % full and battery voltage.
PAGE 7
History data--displays only when program P7 is set to L3 or L4. H1: Cumulative lifetime Amp-hours drawn from the battery. Acts like an odometer for batteries. Press and hold Reset for 5 seconds to reset to 0.00 History data: for each of the last five charge-discharge cycles: P7 must be set to L3 or L4. Press and hold Select until H1.1 appears. Use SELECT button go down the table rows. For each row, push RESET to step back in time up to five earlier charge cycle periods.
PAGE 8
System Information Ba ery Type and Connec on (example: AGM, Series, 12V) Total AH Capacity Series Parallel Series/Parallel Example: Two 6 volt batteries @ 230 AH capacity: 12V 230 AH Example: Two 6 volt batteries @ 230 AH capacity: 6V 460 AH Example: Two 6 volt batteries @ 230 AH capacity: 12V 460 AH -Increases Amps -Increases Voltage -Increases Voltage -Does not increase Amps (20 Hr. rate) Shunt Type -Increases Amps -Does not increase Voltage (500 A‐50 mV, 100 A‐100mV, etc.