Spec Sheet

ManualsBrandsBogen ManualsPublic Address DeviceInput Module Public Address

ARCHITECT & ENGINEER SPECIFICA

TIONS (cont.)

Microphone Input Module (MIC2X) The MIC2X module

shall ha

ve an electronically-balanced input with XLR connec-

tor. It shall interface with low-impedance dynamic micro-

phones.

It shall also interface with electret condenser micro-

phones and shall have an internal 24V DC phantom power

supply to provide the bias supply that is enabled by a PCB

jumper.The module shall have a gain control that will allow the

gain to be adjusted fr

18 dB to 62 dB.

It shall have the abil-

ity to mute lower priority modules and be muted by higher

priority modules.The module shall be able to assume any of 4

priority levels. The module shall have a VOX/gating circuit to

control muting of lower priority modules and its internal gat-

ing circuit with a threshold control. It shall have a built-in lim-

iter, with a threshold control, to limit the maximum output

level of the module. The module shall have bass and treble

controls with cut only of

10 dB at 100 Hz and 3 kHz, respec-

tively.The module shall have a voice enhancement control for

improving voice intelligibility. The module’s output shall be

assignable to either or both of two mixing buses.

Stereo Aux Input Module (SAX1R) The SAX1R module

shall be a stereo, high-impedance, unbalanced input module.

The module shall have two RCA jacks for its input connec-

tors.The module shall have a gain/trim control that will allow

the gain to be adjusted from -20 dB to +6 dB relative to 0 dB

nominal gain. It shall have the ability to mute lower priority

modules and be muted by higher priority modules.The mod-

ule shall be able to assume any of 4 priority levels. It shall have

a continuously variable ducking control that will enable atten-

uation of the input signal from a minimum of

10 dB to a max-

imum of 48 dB relative to the normal unmuted condition and

a gradual fade back from mute when the mute or gate control

is deactivated. The module shall have a VOX/gating circuit to

control muting of lower priority modules and its internal gat-

ing circuit, with controls for threshold and duration.The mod-

ule shall hav

e bass and tr

eble controls with cut or boost of

dB at 100 Hz and 10 kHz, respectively.The module’s outputs

shall be independently assignable to each of two mixing buses.

The module shall allow stereo sources to be summed and sent

mono to either or both of two mixing buses.

Transformer-Balanced Input Module (TBL1S) The

TBL1S input module shall be a transformer-isolated, line-level,

balanced input module

. The module shall have a pluggable 3-

pin screw terminal input barrier strip connector to make the

input connection. The module shall have a jumper selectable

input impedance of 600 ohms or 10k ohms.The module shall

have a gain/trim control that will allow the gain to be adjusted

from -11 dB to +19 dB. It shall have the ability to mute lower

priority modules and be muted by higher priority modules.

The module shall be able to assume any of 4 priority levels.

The module shall have a VOX/gating circuit to control muting

of lower priority modules and its internal gating circuit with

controls for threshold and duration. It shall have a continuous-

ly variable ducking control that will enable attenuation of the

input signal from a minimum of -

10 dB to a maximum of -72

dB relative to the normal unmuted condition and a gradual

fade back from mute when the mute or gate control is deac-

tivated. The module’s output shall be assignable to either or

both of two mixing buses.

Telephone Input Module (TEL1S) The TEL1S module

shall have a transformer-isolated, balanced input and configu-

ration jumpers that will allow it to interface with both wet and

dry loop telephone systems. In the dry loop mode, this mod-

ule shall allow connections to page port systems. In the wet

mode of operation, it shall allow connections to both ground

start and loop start telephone systems.The module shall have

a 6-pin screw terminal input barrier strip connector to make

the input connection. The module shall provide for the con-

nection of an external talk-battery power supply of 48V DC.

The module shall have a gain control that will allow the gain

to be adjusted from 0 dB to 30 dB. It shall have the ability to

mute lower priority modules and be muted by higher priority

modules.The module shall be able to assume any of 4 priori-

ty levels.The module shall have a VOX/gating circuit to control

muting of lower priority modules and its internal gating circuit

with controls for threshold and duration. It shall have a built-

in limiter

with a thr

eshold contr

ol,

to limit the maximum out-

put level of the module.The module’s output shall be assigna-

ble to either or both of tw

o mixing buses.

one Generator Input Module (TNG

1S) The

TNG

input module shall be a multiple tone generator input module.

The module shall have a 5-pin screw terminal input barrier

strip connector to make the trigger connections.The module

shall include 8 tones: 512 Hz burst/steady, slow whoop, siren,

mechanical bell, Klaxon, night ringer, double chime, and door-

bell tones.The module shall permit 4 of the 8 tones to be trig-

gered. Momentary and continuous playback modes shall be

available.The module shall have a level control. It shall have the

ability to mute lower priority modules and be muted by high-

er priority modules. The module shall be able to assume any

of 4 priority levels.The module shall have a gradual fade back

from mute when the mute control is deactivated. The mod-

ule’s output shall be assignable to either or both of two mix-

ing buses.