Communications Tilt Mount Adapter Installation Instruction Manual

ManualsBrandsBogen ManualsNetwork CardTMA812

50 Spring Street, Ramsey, NJ 07446 USA

Tel. 201-934-8500 • Fax: 201-934-9832

www.bogen.com

Specifications subject to change.

54-2187-01A 0810

Installation Instruction Manual

TMA812 Tilt Mount Adapter

for NEAR A8 and A12 Loudspeakers

Summary of content (8 pages)

PAGE 1
TMA812 Tilt Mount Adapter for NEAR A8 and A12 Loudspeakers Installation Instruction Manual 50 Spring Street, Ramsey, NJ 07446 USA Tel. 201-934-8500 • Fax: 201-934-9832 www.bogen.com Specifications subject to change. © Copyright 2008 Bogen Communications, Inc.
PAGE 2
TMA812 - Tilt Mount Adapter Components (2) POLE ADAPTERS (4) #6 POLE ADAPTER SCREWS STATIONARY MOUNTING BRACKET (4) #6 MOUNTING BRACKET SCREWS ADJUSTABLE MOUNTING BRACKET ITEMS INCLUDED WITH A8/A12 LOUDSPEAKER (2) SELF ADHESIVE RUBBER DISKS (4) MOUNTING CHAIN HOOKS (4) MOUNTING CHAIN HOOK WING NUTS A8/A12 SPEAKER HEX SOCKET SAFETY BOLT (4) #10 AXLE/ADJUST SCREWS (2) MOUNTING CHAINS SPEAKER MOUNTING BRACKET NYLON TIE 8 FT.
PAGE 3
1A WALL MOUNTING: Attaching Stationary Mounting Bracket to a Wall or other Flat Surface A) Using proper anchors* (not supplied), attach STATIONARY MOUNTING BRACKET to wall or flat surface. WALL OR FLAT SURFACE B) Skip ahead to Section 3 to continue with Speaker Adjustable Mounting Attachment Installation. *NOTE: WHEN MOUNTING TO WALL OR FLAT SURFACE, BE SURE THE USER SELECTED ATTACHMENT AREA AND THE ANCHORS ARE TOGETHER ABLE TO SAFELY SUPPORT AT LEAST 300 LBS.
PAGE 4
2 Attaching the Mounting Bracket Assembly to a Pole A) Thread NYLON TIE thru Tie Slots and around pole to TEMPORARILY hold the Mounting Bracket Assembly in place on pole. MOUNTING BRACKET ASSEMBLY SLOTS POLE B) Insert (4) MOUNTING CHAIN HOOKS and attached WING NUTS through the most appropriate top & bottom Bracket Assembly slots.
PAGE 5
3 Attach A8/A12 Speaker and Speaker Mounting Bracket to the Adjustable Mounting Bracket A) Attach ADJUSTABLE MOUNTING BRACKET to the A-Series SPEAKER MOUNTING BRACKET by using 4 (#6) Mounting Screws to create the SPEAKER MOUNTING ASSEMBLY. B) Adhere the 2 Self-Adhesive Rubber Disks to the Speaker Cabinet as shown below.
PAGE 6
4 Attach Speaker Mounting Assembly to Stationary Mounting Bracket A) Place Speaker Mounting Assembly on the Stationary Mounting Assembly by putting the FRONT TABS of Speaker Assembly into the two FRONT CATCH slots of the Mounting Assembly (see INSET 1). B) With both Front Tabs hooked securely into both Front Catch slots, gently rotate Speaker Assembly back until both REAR TABS “snap” into both REAR CATCH slots (see INSET 2).
PAGE 7
5 Speaker Assembly Angle Adjustment and Locking Procedure A) Loosely Insert 2 (#10) AXLE SCREWS to both sides of Stationary Mounting Bracket and into the Speaker Assembly Bracket. This will provide safe retention of the Speaker Assembly. B) Pinch inward both sides of the ANGLE ADJUSTMENT WINGS on the Mounting Bracket to rotate the Speaker Assembly to desired angle. Front Tabs on each side will then engage ADJUST ANGLE HOLES on the Mounting Assembly.
PAGE 8
6 Speaker Safety Cable and Tether Link Attachment Installation A) Find the SAFETY ATTACHMENT POINT located on the rear of the A8/A12 Speaker. Using the (1/4”- 20 x 1/2”) HEX SOCKET SAFETY BOLT and the LOCK WASHER, secure the SAFETY TETHER LINK into the Safety Attachment Point, vertically, as shown.