Data Sheet

The amplifier shall be a Bogen Wall-Mount Power
Vector Amplifier, Model WV100, WV150 or WV250.
The amplifier shall be compatible with both high-
(70/25V) and low- (4/8-ohm) impedance speakers,
with the capability of 100, 150, or 250 watts, respectively.
The amplifier shall provide 8 module bays for plug-in
input modules with two of the bays also capable of
handling plug-in signal processing output modules.
There shall be 4 levels of priority between modules.
Each of the 8 module bays shall have an associated
independent volume control. Each independent
volume control shall have a signal/clip LED to
indicate if a clipping condition is occuring at the
moduleʼs output. Each amplifier shall also include
detented bass and treble controls, as well as a motor-
ized master volume control, which can be remotely
operated using the RVCP accessory (sold separately).
The amplifier shall include an adjustable output level
limiter with indicator LED. A tape output jack shall be
available on the front panel and an optional front
panel input combo jack with 1/4" stereo phone and
female XLR capabilities may be installed.
Screw terminals shall be provided for invoking a
master mute function that will interrupt all audio from
the mixer section of the amplifier.
An 11-segment LED output level meter will register
either the average or peak level of the amplifierʼs
output level, determined by an Average/Peak switch.
Each amplifier shall have a Tone Control Bypass
switch and a Low-Cut Filter switch located on the rear
of the amplifier in module bay 6.
A switch will permit the selection of transformer-
coupled output or direct output for speaker runs.
Master mute and remote volume control functions are
controlled using a screw terminal.
The amplifier shall be flush-mounted or surface-
mounted into a wall using either a BBF or BBS back
box (sold separately). A front cover door shall be
required (WMAD sold separately). Each model shall
measure 14-1/8" W x 21" H. The WV100 shall weigh
27 lb.; the WV150, 29 lb.; and the WV250, 28 lb.
Architect and
Engineer
Specifications
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel.: [phone] • Fax: [phone]
www.bogen.com
Technical
Specifications
Power Output (RMS)
WV100: 100W (140W Typical, @1 kHz/0.1%/4W)
WV150: 150W (200W Typical, @1 kHz/0.1%/4W)
WV250: 250W (340W Typical, @1 kHz/0.1%/4W)
Frequency Response
Transformer: 45 Hz to 20 kHz; 0/-2 dB @ FRP
Direct: 20 Hz to 20 kHz; 0/-1 dB @ FRP
Distortion
Transformer: 0.5% THD+N, Maximum,
Full-rated bandwidth @ FRP
Direct: 0.1% THD+N, Maximum,
Full-rated bandwidth @ FRP
Signal-to-Noise
Fundamental: -94 dB*
With Aux Module: -70 dB*
With Mic Module: -60 dB*
With Tel Module: -70 dB*
Tone Controls
Bass Frequency: 100 Hz (+/- 10 dB minimum)
Treble Frequency: 10 kHz (+/- 10 dB minimum)
Low Cut Frequency: 125 Hz @ -6 dB/octave
Sensitivity: 0.4V (at backplane connector)
Output Regulation: 2 dB or better, no load to full load
Output Impedance
Transformer-Coupled: 70V, 25V, 8 ohms; balanced or unbalanced
Direct Coupled: 4 ohms unbalanced
Tape Out
Output Level: 4 VRMS @ FRP
Output Impedance: 50 ohms maximum
Overload Protection: Electronic overload protection
(auto reset)
Thermal Protection: Thermistor attached to heat sink
Line Fusing: Resettable circuit breaker
Cooling: Thermally controlled 3-speed fan
Power Consumption: WV100: 2.0A @ 120V AC, 60 Hz
WV150: 3.5A @ 120V AC, 60 Hz
WV250: 5.5A @ 120V AC, 60 Hz
Thermal Emissions: WV100: 495.2 BTU/hr.
WV150: 696.7 BTU/hr.
WV250: 911.9 BTU/hr.
Dimensions:
WV100/150/250: 14-1/8" W x 21" H
BBF: 14-1/2" W x 24-3/4" H x 3-7/8" D
BBS: 16-1/4" W x 26-3/4" H x 3-7/8" D
WMAD: 16-1/4" W x 26-3/4" H x 1" D
Product Weight:
WV100: 27 lb.
WV150: 29 lb.
WV250: 28 lb.
BBF: 12 lb.
BBS: 16 lb.
WMAD: 9 lb.
* Referenced to full-rated power (FRP) output level, 20 Hz to 20 kHz bandwidth limited.
All specifications subject to change without notice
.