SRR ROTARY MOWERS Important: Model Numbers Read Safety Rules and 111-152A Instructions Carefully 111-162A Thank you for purchasing an American built product. FORM NO, 770-0838 PRINTED IN US.A.
Safe Operation Practices . Assembly Instructions . Operation Instructions , Adjustments. .. Lubrication .. Maintenance .. PP CPO SO Nt INDEX Off-Season Storage .. . . Exploded Parts View . Do LIMITED WARRANTY For one year from the date of original retail purchase, MTD PRODUCTS INC will either repair or replace, at its option, free of charge, F.0.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship.
SOON §_warning § To reduce the potential for any injury, comply with the following safety instructions. Failure to comply with the instructions may result in personal injury. SAFE OPERATION PRACTICES FOR WALK-BEHIND MOWERS TRAINING o walks or roads. 1. it is suggested that this manual be read in its 4. After striking a foreign object, stop the entirety before attempting to assemble or engine, remove the wire from the spark plug, operate this unit.
N “Lower Handle > FIGURE 2. il Continual L leT T Handle Hex Alt FIGURE 3. ASSEMBLY INSTRUCTIONS NOTE This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see operating section of this manual for proper fuel and engine oil recommendations. 1. Extend throttle control which is attached to the engine at the rear of the mower and place on the floor. Be careful not to bend or kink control wire, 2. Fasten hole in lower handle over weld pins in handle mount brackets on deck.
. Secure throttle control cable to handle with provided. See figure 4. 6. Check ALL nuts and bolts for correct tightness. FIGURE 4. &CAUTION Please note that the chute deflector on your mower is in an upright position. It is had in that position by a e S Hipping block. This block is used for shipping purposes only. It must be removed and discarded before your mower is put into operation. See figure 5. FIGURE 5.
OPERATION CAUTION D0 NOT OPERATE R R RN GUARD OR ENTIRE GRASS CATCHER IS IN ITS PROPER PLACE. FIGURE 6. Keep hands and feet away from the chute area on cutting deck. See figure 6. NOTE For shipping purposes your mower is set with the wheels in a low cutting height position. For best results raise the cutting position until it is determined which height is best for your lawn. See adjustment section, 1, FILL SUMP WITH OIL using a high duality detergent oil classified “For Service MS.
FIGURE. THROTTLE If adjustment becomes necessary, the throttle control wire assembly can be reset as folios: 1. Loosen, but do not remove, screw securing throttle control wire assembly at engine. See figure 8. 2, Move throttle control lever on handle to “FAST” position. 3. Move lever, to which control wire is fastened at engine, to full open position and re tighten screw to secure throttle control wire assembly. Control Wire Screw On & (T FIGURE 8.
Idle Adjusting Screw # » Needier Valve 398974 CARBURETOR ADJUSTMENT FIGURE 9. LUBRICATION IMPORTANT Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on lawn mower. Wheels—Wheel bearings are of self-lubricating Fortifier. They require no lubrication. However, if the wheels are removed for any reason, Lubricate the surface of the axle bolt and the inner surface of the wheel with light oil. A 4 oz. plastic bottle of light oil lubricant is available.
Blade Mounting Torque 3/8” Dia. Bolt 375 in. Ib. min., 450 in. Ib. max, 516" Dia. Bolt 150 in. Ib. min., 250 in. ib. max. To insure safe operation of your unit, ALL nuts and bolts must be checked periodically for correct tightness. DECK The underside of mower deck should be cleaned after each period of use as grass clippings, leaves, dirt and other matter will accumulate. This accumulation of grass clippings, etc.
FIGURE 13. SPARK PLUG The spark plug should be cleaned (see figure 12) and the gap reset to a clearance once a season (see figure 13). Spark plug replacement is recommended at the start of each mowing season; check engine manual for correct plug type. NOTE Whenever the spark plug is removed for cleaning, it is advisable to replace the spark plug gasket with a new gasket.
-NOTE The use of any accessory on this Rotary Mower other than those manufactured by the mower manufacturer is not recommended. GRASS CATCHER Moet No. 191-003A is available as optional equipment for the mowers shown in this manual. possessor WARNING 1. The mower should not be operated without the entire grass catcher or chute deflector in place. 2. The mower should not be operated without the protective shield on the rear of the deck in place.
111-152A 111-162A 12 IF YOU WRITE TO US ABOUT THIS ARTICLE WAYS MENTION THIS MODEL & SERIAL NO T This instruction manual covers various models and all specifications shown do not necessarily apply to your mated. Specifications subject 10 change without notice or obligation.
52A PARTS LIST FOR MOWER Qz__A MODELS 111-152A AND 111-162A REF| PARTNER COLON | PART NO. COLOR NEW o "hideaway TOE | Timezone CODE DESCRIPTION PART 3| 7310275 7310275 Shroud 4| 710-0289 710-0289 Hex Bolt, %-20 Engine 6] 710-0654 710-0664 Deli( Wash. Hd. Self-Tap Scr, x .88" g. 71 12035 12035 Handle Mtg. Bret. Ass'y.
PARTS INFORMATION POWER EQUIPMENT PARTS AND SERVICE Parts and service for alf MTD manufactured power equipment are available through the authorized service firms listed below. All orders should specify the model number of your unit, part numbers, description of pairs and the quantity of each part required. NOTE: If any parts are found to be missing or defective u that immediate replacement can be made. ALABAMA BIRMINGHAM Auto Electric & Carburetor Co. . .. 2625 4th Ave.