Ultra Wide Dynamic (IR Waterproof) Dome Camera User's Manual
1 Overview 2 Notes SA series Ultra WDR cameras are new, CCTV cameras which adopt Pixim's innovative “SEAWOLF” image sensor chip based on Digital Pixel System ® 1. Use the Appropriate Power Supply The input power will be DC12V or DC12V/AC24V dual-power. Be sure to connect technology. The resolution is up to 690TVL-E and the industry-leading wide dynamic it to the appropriate power. Wrong connection may cause malfunction and damage to range is up to 120dB.
.Features All directional bracket* All directional bracket, easy control. SEAWOLF Image Sensor This camera adopts innovative DPS(Digital Pixel System) image sensor and image processing technology. The sensor picks up details from each pixel based on hundreds of samples per video frame. vs CCD's limited exposures, to ensure wider dynamic range than is possible with analog CCD. The image quality is even brilliant under extreme lighting conditions.changeable lighting condition.
Camera installation 1 loose the 3 glass cover screw by screwdriver ,take the glass cover out. 2 loose the Installed setscrews , to separate the subpanel from camera body. 3 Drill 3 holes in the position needed in accordance with the installation hole on the subpanel , push the Expansion Bolt inside then tighten the screws,make the installation hole aim at the three screws and fix it.
Adjust ment for camera direction 1 When the camera fixed on the ceiling , you can ajust the angle by adjustment of the 3 axis bracket. Maximmum 355 vertical rotation, 35 horizontal rotation,355 dipping rotation. 2 Adjust ZOOM to the position you need, then adjust FOCUS to get clearer image. 3 Fix the glass cover on the camera body. Parts instruction 1. Cover dome 4.
Adjusting the camera direction 355 35 Lens rotation 1 When the camera is fixed on the ceiling, you can adjust the camera viewing angle. You can rotate your camera leftward or rightward (Panning), and can change the slope of your camera upward or down ward (Tilting). 2 In case of panning, the rotation limit of yourcamera is set to 355 degree (100 degree clockwise and 255 degree counterclockwise). The rotation is stopped by the Stopper inside of the camera.
Horizontal Rotation 355 Parts instruction 1 2 3 4 5 6 7 Vertical Rotation45 dipping rotation355 When your camera is fixed to the wall, you can adjust camera s three-dime nsion al brac ket to the angle you need. 1.Horizontally rotating angle 355 (Bracket panel and main board installing panel can both be rotated.) 2. Vertically rotating angle 45 Adjust the lens focal length to the position you need and adjust the lens focus again to get a clear picture.
OSD Menu Setup Menu button for choice Move Up And Down By Up And Down Button Move Horizontally Or Modify Parameter By Left And Right Button WDR Control: Press Enter to show the menu, move the cursor to WDR Control, set MEDIUM, NORMAL, LOW, HIGH by left and right button; choose the setting for WDR in accordance with the lighting condition, set High in strong lighting contrast to realize higher quality image. WDR ZONE SELECT:WD NROMAL/SAFE AREA/ATM/LOW 1/3. 6.
7.Technical parameter: LENS SELECT: Move cursor to LENS SELECT, set LENS SELECT by Right and Left button as : Sensor Resolution 690HTVL-E 0.1Lux >50dB AGC OFF medium, normal, low, high BLC ON, OFF AGC normal, low, high Mode Tracking White Balance, Auto White Balance(ATW) White Balance Automatic Auto White Balance 2200~10000 K D/N D/N Control: OFF, External Control, Auto; ON SYNC Mode as: OFF; Auto;GPIO: External Control; On.
Technical parameter: Technical parameter: B-1 Model B-2 Sensor B-3 1/3 690HTVL-E 0Lux;(IR-ON ) Mini illumination ON, OFF AGC normal, low, high Mode Tracking White Balance, Auto White Balance(ATW) White Balance Automatic Auto White Balance 2200~10000 K D/N SYNC Mode DC12V/AC24V DC12V DC12V/AC24V current <400mA <450mA <400mA <450mA 4-9mm Auto iris 2.8-12mm IR Range IR CUT 2.
Technical parameter: Technical parameter: D-1 Model D-2 Sensor D-3 1/3 DPS Sensor PAL/NTSC 690HTVL-E Resolution Menu Control Menu Control BLC ON, OFF AGC normal, low, high Mode Tracking White Balance, Auto White Balance(ATW) White Balance Automatic INTERNAL DC12V <450mA <400mA 4-9mm <400mA 4-9mm Auto iris IR Range IR CUT DC12V DC12V/AC24V 0.1Lux 2.8-12mm DC12V/AC24V <450mA 2.
Technical parameter: Technical parameter: G-1 Model G-2 Sensor G-3 1/3 690HTVL-E 0Lux;(IR-ON ) Mini illumination OFF S/N Ratio AGC Mode Tracking White Balance, Auto White Balance(ATW) Auto White Balance D/N OFF, External Control, Auto; ON SYNC Mode INTERNAL DC12V/AC24V DC12V DC12V/AC24V Current <400mA <450mA <400mA <450mA 4-9mm Auto iris 20M IR Range IR CUT 2.8-12mm Fix iris 2.
