Operation Manual

•
Place the outer duct with the fixed rail (3) onto the extractor hood (Fig. E). Fas
parallel to the other rails (1+2).
•
Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct
is aligned with the vents at the top.
duct or sliding back into the outer duct.
•
For extraction mode, correctly position the flexible
• Pull the inner duct cover up a
nd
screwing in the plate screws (7)
(Fig. F)
I
II
Installing the activated carbo
nstalling the activated carbonstalling the activated carbo
nstalling the activated carbo
n filter for recirculation mode
n filter for recirculation moden filter for recirculation mode
n filter for recirculation mode
•
Remove the aluminum grease filter.
•
Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the
extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it
clicks into place.
• Reinstall the alumin
um grease filter
NOTE
NOTENOTE
NOTE:
::
:
The activated carbon filter absorbs
odours
Electrical connection
Electrical connectionElectrical connection
Electrical connection
WARNING:
WARNING:WARNING:
WARNING:
•
The installation to the mains supply must conform to the local standards
•
Improper connection may cause to an
• Do not modify the appliance
plug
an authorized specialist.
•
The accessibility of the power plug must be ensured in order to disconnect the
supply in case of an emergency.
•
Ensure that your mains power corresponds with the specifications of the appliance. The specifications are
printed on the rating label.
•
Connect the mains cable to a properly installed and earthed wall outlet.
The
extractor hood is operated via pushbuttons.
switched on and off with the
corresponding
Lowest fan setting
Moderate fan setting
20
Place the outer duct with the fixed rail (3) onto the extractor hood (Fig. E). Fas
ten the rail (3) to the wall
Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct
is aligned with the vents at the top.
Determine the extension length of the duct
cover by pulling up the inner
duct or sliding back into the outer duct.
For extraction mode, correctly position the flexible
extraction hose (not supplied).
nd
fasten the duct unit on the side to the
previously
(Fig. F)
.
n filter for recirculation mode
n filter for recirculation moden filter for recirculation mode
n filter for recirculation mode
Remove the aluminum grease filter.
Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the
extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it
um grease filter
.
odours
and must be replaced at least every six
months
The installation to the mains supply must conform to the local standards
and regulations.
Improper connection may cause to an
electric shoc
electric shocelectric shoc
electric shock!
k!k!
k!
plug
. If the plug does not fit properly to the outlet, let install a proper outlet by
The accessibility of the power plug must be ensured in order to disconnect the
appliance
Ensure that your mains power corresponds with the specifications of the appliance. The specifications are
Connect the mains cable to a properly installed and earthed wall outlet.
Startup / Operation
Startup / OperationStartup / Operation
Startup / Operation
extractor hood is operated via pushbuttons.
The individual fan settings as
well
corresponding
buttons.
Highest fan setting
Lighting
ten the rail (3) to the wall
Slide the inner (upper) duct along the slide fixture into the outer (lower) duct. Make sure that the inner duct
cover by pulling up the inner
previously
mounted rail (2) by
Place the carbon filter onto the air intake of the extraction duct. Make sure that the mounting pins on the
extraction duct engage the mounting slots of the carbon filter. Turn the respective filter clockwise until it
months
regardless of use.
and regulations.
. If the plug does not fit properly to the outlet, let install a proper outlet by
appliance
from the power
Ensure that your mains power corresponds with the specifications of the appliance. The specifications are
well
as the lighting can be