Operation Manual

Drill two mounting holes
Ø 7 mm at the respective
positions in the wall, meas-
ured in a height from the
ground level of about
750 mm. Insert the dowels
and screw in the hooks.
• Connect the chains
with the hooks.
Electrical connection
Electrical connectionElectrical connection
Electrical connection
Information for the
Information for the Information for the
Information for the
authorized expert
authorized expertauthorized expert
authorized expert
WARNING:
WARNING:WARNING:
WARNING:
•
The installation to the mains supply must conform
to the local standards and regulations.
•
Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
bles is not permitted.
• Improper connection m
ay cause to an
shock
shockshock
shock!
•
Before connecting, ensure that the power supply
corresponds with the information on the rating l
bel and the wiring diagram.
•
The appliance is suitable for three
current (400V 3N~50/60Hz).
• The appliance can be
adjusted for single
current by a respective bypass on the terminal
block,
based on the circuit diagram below. Select
a suitable cord as mains cable, considering the
connection type and nominal power of the oven.
•
Fix the mains cable in the tension
•
Make sure to connect the protective ground to the
terminal of
the marked terminal block.
•
The electrical installation of the oven should be
equipped with an emergency switch, which
switches off the whole appliance from the mains
supply in an emerge
ncy. The distance between
the contacts of the emergency switch must be at
least 3 mm.
7
with the hooks.
authorized expert
authorized expertauthorized expert
authorized expert
The installation to the mains supply must conform
to the local standards and regulations.
Connecting the appliance to a domestic power
socket or using multiple sockets or extension c
a-
ay cause to an
electric
electric electric
electric
Before connecting, ensure that the power supply
corresponds with the information on the rating l
a-
The appliance is suitable for three
-phase and AC
adjusted for single
-phase
current by a respective bypass on the terminal
based on the circuit diagram below. Select
a suitable cord as mains cable, considering the
connection type and nominal power of the oven.
Fix the mains cable in the tension
relief.
Make sure to connect the protective ground to the
the marked terminal block.
The electrical installation of the oven should be
equipped with an emergency switch, which
switches off the whole appliance from the mains
ncy. The distance between
the contacts of the emergency switch must be at
•
Arrange the mains cable in such a way that it
does not get in contact with any hot components
of the appliance. Do not lead it over sharp edges
or corners.
Connection
Connection Connection
Connection wiring diagram
wiring diagramwiring diagram
wiring diagram
Permissible connection methods
Permissible connection methodsPermissible connection methods
Permissible connection methods
CAUTION:
CAUTION:CAUTION:
CAUTION:
Each connection requires the protective ground of the
mains to be connected to the E
HINWEIS
HINWEISHINWEIS
HINWEIS:
::
:
L1, L2, L3 = Phase
N = Neutrale Leitung
E = Schutzleiter
Recommendation is the connection
Recommendation is the connectionRecommendation is the connection
Recommendation is the connection
phase circuit 3 x 16 A!
phase circuit 3 x 16 A!phase circuit 3 x 16 A!
phase circuit 3 x 16 A!
220-240V~
50/60Hz
380-
415V 3N~
50/60Hz
H05 VV-F 3G
4mm²
H05 VV-
F 5G
1.5mm²
Startup / Operation
Startup / OperationStartup / Operation
Startup / Operation
Before initial use
Before initial useBefore initial use
Before initial use
• Clean the
hob as well as the
therein located accessories. Follow the instru
tions that we give you in the chapter "Cleaning
and Maintenance".
•
In order to burn any manufacturing residue
-
Heat the closed oven for approx. 30 minutes at
240°C.
Use the heating function [Upper/lower
heat].
- Place
cookware with water on each
zone. Allow the
appliance
and afterwards at low
est setting each for about
10 minutes.
Arrange the mains cable in such a way that it
does not get in contact with any hot components
of the appliance. Do not lead it over sharp edges
Permissible connection methods
Permissible connection methodsPermissible connection methods
Permissible connection methods
Each connection requires the protective ground of the
mains to be connected to the E
terminal.
Recommendation is the connection
Recommendation is the connectionRecommendation is the connection
Recommendation is the connection
option to a three
option to a threeoption to a three
option to a three-
--
-
415V 3N~
380-415V 2N~
50/60Hz
F 5G
H05 VV-F 4G
1.5mm²
hob as well as the
oven interior with all
therein located accessories. Follow the instru
c-
tions that we give you in the chapter "Cleaning
In order to burn any manufacturing residue
:
Heat the closed oven for approx. 30 minutes at
Use the heating function [Upper/lower
cookware with water on each
cooking
appliance
working at the highest
est setting each for about