Installation Guide

ManualsBrandsBon Tool ManualsCaulk & SealantsSpeedy Mortar Pointer Caulk Gun with Black & Decker Drill

4430 Gibsonia Rd. • Gibsonia, PA 15044 • USA • www.bontool.com

SAFETY INSTRUCTIONS

Warning: When using electric tools always follow basic safety

precautions to reduce the risk of fire, electric shock and

personal injury.

1. KNOW YOUR POWER TOOL. Read this manual carefully

and the drill manual associated with the drill used with this

Quickpoint Drill-Mate Mortar Gun.

2. Do not put hands in hopper while tool is plugged in.

3. Do not tighten or install parts while tool is plugged in.

4. Do not use the water hose to clean tool. (see cleaning

instructions)

5. In the event that tool plugs or jams, do not continue to

operate tool. See trouble shooting.

6. Before operating tool, be sure nozzle Key Allen Wrench is

inserted and lokcing nozzle in place.

7. Do not use this tool to dispense materials other than water

based cementacious mortars.

8. Do not overreach. Keep proper footing and balance at all

times.

9. Do not abuse power cord. Never carry tool by the drill

cord.

10. Keep hands away from all moving parts. (Install cam

guard before using)

11. Store idle tool. When not in use, store your tool in a dry

secure place. Keep out of the reach of children.

ACCESSORIES

• 1 - Angled steel tip no. 552-A

• 1 - Wide steel tip. 552

• 1 - Narrow steel tip no. 551

• 1 - Large steel tip no. 553

• 2 - “U” blades

• 3 - Tip blade sets

• 2 -

- 28 x

Stainless steel set screws

• 1 - Extra nozzle key Allen wrench

• 1 - 16 oz. Scoop no. 554

• 1 - 8 oz. Gibco’s - MRF

Tip blades can be made from 1/8” electrician’s snake.

Bend with pliers and vice to contour below or send for

replacement tips.

A set consists of one long, one short blade and on “U” blade.

<-- Insert this end in blade coupling.

Caution: Protect eyes when cutting

hardened wire.

NOZZLE ASSEMBLY

1. Drop metal nozzle tip into nozzle tip holder. Then insert

retaining collar as shown.

2. Slip the assembly over the front barrel of the gun. Pull the

nozzle assembly firmly against the front face of the gun

barrel until the metal nozzle tip is seated tightly in the

nozzle holder.

3. Insert the allen wrench key into the holes at the back of the

nozzle assembly. The allen key, when properly placed,

will fit in the slot at the back of the second o-ring.

Note: The nozzle assembly can now

be rotated for vertical or horizontal

applications. When assembling,

make sure all mating surfaces are

clean to insure proper seating. Put

lubricant such as Vaseline on o-ring

area and area where Allen Key runs.

AUGER ASSEMBLY

1. Install the Blade-Coupling (#502) on to the Auger by

tightening the Socket set screw on the flat of the auger

shaft.

2. The short leg of the U-Blade (#504) is inserted between the

Tip-Blade-Set (#503) with the short-blade above (so that the

set screw tightens on this blade first) and the long blade

below.

INSTRUCTIONS

#14-188 Quickpoint

4430 Gibsonia Rd. • Gibsonia, PA 15044 • USA • www.bontool.com

IS14188 08/09

PAGE 1 OF 4

Summary of content (4 pages)

PAGE 1
INSTRUCTIONS #14-188 Quickpoint SAFETY INSTRUCTIONS Warning: When using electric tools always follow basic safety precautions to reduce the risk of fire, electric shock and personal injury. 1. KNOW YOUR POWER TOOL. Read this manual carefully and the drill manual associated with the drill used with this Quickpoint Drill-Mate Mortar Gun. 2. Do not put hands in hopper while tool is plugged in. 3. Do not tighten or install parts while tool is plugged in. 4. Do not use the water hose to clean tool.
PAGE 2
AUGER ASSEMBLY CON’T 3. The Long-leg of the U-Blade must be positioned against the left side of the set-screws when looking from the front of the blade assembly. 6. Align Set Screws and then tighten when the Cam-Coupling is in proper position (#703-S & 502-S). Push Auger shaft so that the es the Roller stop. Cam-Coupling on to the Cam-Roller just touch- 7. Put steel nozzle (#551, 552, 553, 552A) followed by Retainer collar (#751) into NozzleHolder (#750) then push assembly on to Barrel. ASSEMBLY 8.
PAGE 3
perpendicular to the wall or slightly angled away from the direction of travel. Fill vertical joints from bottom to top. MOUNTING A DRILL CON’T 4. Drill with chuck and male Cam-Stud. 5. The Quikpoint will deliver mortar straight down, horizontally and up to a 55˚ angle above the horizontal. Use angled nozzle #552-A for overhead applications. 5. Slip the Ring-Clamp (#711) over the drill and Drill Mount Arms (#710). CLEANING AND MAINTENANCE 1. Do not leave mortar in gun for more than one hour. 2.
PAGE 4
MORTAR MIXES CON’T 1. A richer mix will work more easily through the gun. 2. If your mortar mix is plugging or the Quikpoint is laboring to put your mix out, then use Gibco’s-MRF additive or a good plasterisizer. A. Shake before using Gibco’s-MRF pump aid additive. B. Add to mixing water 1/ 2 oz. of Gibco’s-MRF to 1 gallon of water. Do not exceed 3 oz. of MRF to 5 gallons of water. C. If problem continues, check the Tip Blades (#503) and U-Blade (#504) for wear.