BRV102 USER MANUAL © Boretti B.V.
Contents Safety information Operation First use Daily use Helpful hints and tips 2 4 4 4 6 Care and cleaning What to do if… Technical data Installation Environmental concerns 7 8 10 10 15 Subject to change without notice Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings.
• It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may cause a short-circuit, fire and/or electric shock. Warning! Any electrical component (power cord, plug, compressor) must be replaced by a certified service agent or qualified service personnel. 1. Power cord must not be lengthened. 2. Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire. 3.
Service • Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person. • This product must be serviced by an authorized Service Centre, and only genuine spare parts must be used. Environment Protection This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish.
partment let the appliance run at least 2 hours on the higher settings. Important! In the event of accidental defrosting, for example due to a power failure, if the power has been off for longer than the value shown in the technical characteristics chart under "rising time", the defrosted food must be consumed quickly or cooked immediately and then re-frozen (after cooling).
Helpful hints and tips Hints for energy saving • Do not open the door frequently or leave it open longer than absolutely necessary. • If the ambient temperature is high and the Temperature Regulator is set to low temperature and the appliance is fully loaded, the compressor may run continuously, causing frost or ice on the evaporator. If this happens, set the Temperature Regulator toward warmer settings to allow automatic defrosting and so a saving in electricity consumption.
• water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt; • it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time.
5. Switch on the appliance. 6. Set the temperature regulator to obtain the maximum coldness and run the appliance for two or three hours using this setting. 7. Reload the previously removed food into the compartment. Warning! Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer.
Problem Possible cause Solution The lamp is in stand-by. Close and open the door. The lamp is defective. Refer to "Replacing the lamp". The temperature is not set correctly. Set a higher temperature. The door is not closed correctly. Refer to "Closing the door". The door has been opened too frequently. Do not keep the door open longer than necessary. The product temperature is too high. Let the product temperature decrease to room temperature before storage.
Closing the door 1. Clean the door gaskets. 2. If necessary, adjust the door. Refer to "Installation". 3. If necessary, replace the defective door gaskets. Contact the Service Force Center. Technical data Dimension of the recess Height 1030 mm Width 560 mm Depth 550 mm Rising Time 12 h The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.
min. 200 cm2 min. 200 cm2 On the opposite side: 1. Tighten the lower pin. 2. Install the spacer. 3. Install the door. 4. Tighten the upper pin. Ventilation requirements The airflow behind the appliance must be sufficient. Installing the appliance Caution! Make sure that the mains cable can move freely. Do the following steps: 1. Install the appliance in the niche. Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture.
between the appliance and the kitchen furniture is correct. Open the door. Put the lower hinge cover in position. 4mm 44mm 5. Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case. 3. Attach the appliance to the niche with 4 screws. I 6. Attach the covers (C, D) to the lugs and the hinge holes. Attach the hinge covers (E) to the hinge. 4. Push the sealing strip between the appliance and the adjacent cabinet.
Put together the appliance door and the furniture door and mark the holes. Ha Hb 8 mm Hc Hd 8. Install the part (Ha) on the inner side of the kitchen furniture. Ha Hb 11. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). ca. 50 mm 90° 8 mm 21 mm 90° ca. 50 mm 21 mm 9. Push the part (Hc) on the part (Ha). Ha Hc 10. Open the appliance door and the kitchen furniture door at an angle of 90°.
Do a final check to make sure that: • All screws are tightened. • The magnetic sealing strip is attached tightly to the cabinet. Important! If the ambient temperature is low (for example, in the Winter), the size of the gasket decreases. The size of the gasket increases when the ambient temperature increases. Hb 13. Press the part (Hd) on the part (Hb).
Reversibility of the freezer door 180˚ Environmental concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment.
BORETTI B.V. De Dollard 17 1454 AT Watergang T +31(0)20-4363439 F +31(0)20-4361326 S 0900-2352673 (service) E info@boretti.com The Netherlands N.V. BORETTI S.A. Ruperlweg 16 2850 Boom T +32(0)3-4508180 F +32(0)3-4586847 E info@boretti.
