Owners manual

ManualsBrandsBorla ManualsAutomotive11761 S-Type Axle-Back Exhaust System Fits 06-13 Corvette

BORLA PERFORMANCE INDUSTRIES

901 Edison Dr.

Oxnard, Ca. 93033

805-986-8600

TITLE: 2006-2008 Chevrolet Corvette Z06

S Type Rear Section Installation Instructions

PART NO. A-35415 Page 1 of 4

ear Section Installation For

2006-2008 Chevrolet Corvette Z06

Thank you for purchasing a Borla Performance Rear Section Exhaust System.

This Borla Performance Rear Section Exhaust System (Part number 11761) has been designed for

2006-2008 Chevrolet Corvette Z06 equipped with a 7.0L V-8 engine and a manual transmission.

Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary

equipment, tools and experienced personnel needed for proper installation, should perform the installation of this system. However,

if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under car safety

precautions including eye protection.

Please take time to read and understand the following…

By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms

stated below.

It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your

Borla Performance Exhaust System

Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper

operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s

products and/or systems.

Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on

your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your

new Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.

Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing

Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your

engine to discharge exhaust gas easier. The result is more horsepower and torque, longer engine life, and a distinctive throaty

growl- all this, with easy bolt-on installation. These installation instructions have been written to help you in the installation of

your Borla Performance Exhaust System. Please read it completely before installing your system.

Summary of content (4 pages)

PAGE 1
BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr. Oxnard, Ca. 93033 805-986-8600 Rear Section Installation For 2006-2008 Chevrolet Corvette Z06 Precision manufactured using aircraft quality T-304 stainless steel; this system is designed to endure years of heavy use. Installing a Borla Performance Exhaust System on your vehicle will eliminate the restrictive design of the stock exhaust, allowing your engine to discharge exhaust gas easier.
PAGE 2
BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr. Oxnard, Ca. 93033 805-986-8600 Minimum Required Tool List: TOOLS: 1 2 3 4 3/8” Drive Ratchet 3/8” Drive Extension 3” 15mm Socket Pry Bar SHOP SUPPLIES: 1 Spray Lubricant Borla Performance Rear Section Bill of Materials 1. 2. 3. 4. 5. Left over axle pipe Right over axle pipe Muffler assembly 3.00” Accuseal™ clamp (qty 2) Vacuum plug (qty 2) TITLE: 2006-2008 Chevrolet Corvette Z06 PART NO.
PAGE 3
BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr. Oxnard, Ca. 93033 805-986-8600 Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Rear Section Exhaust System.
PAGE 4
BORLA PERFORMANCE INDUSTRIES 5901 Edison Dr. Oxnard, Ca. 93033 805-986-8600 Warning: Use extreme caution during installation. Torque all fasteners according to manufacturer’s torque values and tightening sequence. DO NOT use air impact tools to tighten fasteners on Borla Performance Exhaust Systems. Use of such tools may result in bent flanges or gasket contact areas leading to exhaust leaks. Borla Performance Rear Section Exhaust System Installation 1.