Owners manual

ManualsBrandsBorla ManualsAutomotive11812 ATAK Axle-Back Exhaust System Fits 09-13 Corvette

BORLA PERFORMANCE INDUSTRIES

701 Arcturus Ave.

Oxnard, Ca. 93033

805-986-8600

TITLE: Chevrolet Corvette C6 Rear Section

Installation Instructions

PART NO. A-35631 Rev.A Page 1 of 4

Exhaust System Installation For

Corvette C6

Thank you for purchasing a Borla Performance Exhaust System.

These Borla Performance Rear Section Exhaust Systems (PN’s 11810,11811,11812) are designed for

the Chevrolet Corvette C6 equipped with a 6.2L V-8 engine, automatic or manual transmissions.

Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the neces-

sary equipment, tools and experienced personnel needed for proper installation, should perform the installation of this system.

However, if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under

car safety precautions including eye protection.

Please take time to read and understand the following…

By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms

stated below.

It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your

Borla Performance Exhaust System

Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, im-

proper operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s

products and/or systems.

Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on

your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your

new Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.

These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please

read this document completely before beginning the installation of your system.

Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for

this installation.

To ensure this part number fits your specific model year, please visit our website for the latest model year listings at

www.BORLA.com.

Summary of content (4 pages)

PAGE 1
BORLA PERFORMANCE INDUSTRIES 701 Arcturus Ave. Oxnard, Ca. 93033 805-986-8600 Exhaust System Installation For Corvette C6 These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document completely before beginning the installation of your system. Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for this installation.
PAGE 2
BORLA PERFORMANCE INDUSTRIES 701 Arcturus Ave. Oxnard, Ca. 93033 805-986-8600 Minimum Required Tool List: TOOLS: 1. 3/8” Drive Ratchet 2. 3/8” Drive Extension 3” 3. 15mm Deep Well Socket 4. Pry Bar 1 SHOP SUPPLIES: Spray Lubricant Borla Performance Rear Section - Bill of Materials 11810 11811 11812 TITLE: Chevrolet Corvette C6 Rear Section PART NO. A-35631 Installation Instructions Rev.
PAGE 3
BORLA PERFORMANCE INDUSTRIES 701 Arcturus Ave. Oxnard, Ca. 93033 805-986-8600 Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Rear Section Exhaust System.
PAGE 4
BORLA PERFORMANCE INDUSTRIES 701 Arcturus Ave. Oxnard, Ca. 93033 805-986-8600 Borla Performance Rear Section Exhaust System Installation 1. Place a clamp over each expanded ends of each Over-Axle Pipe. Starting with the R/H Muffler Assembly, and insert inlet into R/H Over-Axle Pipe and carefully insert hangars into runner isolators. Repeat step for the L/H Muffler Assembly. (See Fig. 3 & 4) Figure 3 2. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.