Installation Manual

ManualsBrandsBorla ManualsAutomotiveBORLA 140619 ATAK Cat-Back Exhaust System (Truck Side Exit)

These instructions have been written to help you with the installation of your Borla Performance Exhaust System.

Please

read this document completely before beginning the installation of your system.

Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for

this installation.

Installation for the FORD F-150 Truck

PNs - 140617, 140618, 140619

*PNs - 60564 (163” wheelbase), 60556 (157” wheelbase)

Thank you for purchasing a Borla Performance Cat-Back™ Exhaust System.

Borla Performance Cat-Back™ Exhaust Systems (PN’s 140617, 140618, 140619) are designed for the Ford F-150 (145”

wheelbase) equipped with the 3.5L Ecoboost V6 or the 5.0L V8 engines, 2 or 4-wheel drive, automatic transmissions.

*Borla Performance Adaptor Pipes (PN’s 60564, 60556) extend the above Cat-Back™ Exhaust Systems to fit the following wheel-

bases: 60564 extends fitment to the 163” wheelbase, 60556 extends fitment to the 157” wheelbase. These systems are not included

and must be purchased separately.

Borla Performance Industries recommends that an exhaust shop or professional after market parts installer perform the installation of

this system. However, if you decide to perform the installation on your own it is recommended that two people are used. This instal-

lation should not be performed by one person due to the risk of injury. Ensure the installers use all under car safety precautions in-

cluding eye protection.

Please take time to read and understand the following…

By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms

stated below.

It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your Borla

Performance Exhaust System.

Borla Performance Industries assumes no responsibility for damages occurring from misuse, abuse, improper installation, improper

operation, lack of responsible care, or all previously stated reasons resulting from incompatibility with other manufacturer’s products

and/or systems.

Included with your Borla Performance Exhaust System is a warranty card. Please read it carefully before you begin any work on

your vehicle. If you should have any questions regarding our warranty policy, installation, or any other matter pertaining to your new

Borla Performance Exhaust System, please give us a call at the number provided on the warranty card.

Summary of content (6 pages)

PAGE 1
Installation for the FORD F-150 Truck PNs - 140617, 140618, 140619 *PNs - 60564 (163” wheelbase), 60556 (157” wheelbase) These instructions have been written to help you with the installation of your Borla Performance Exhaust System. Please read this document completely before beginning the installation of your system. Please compare the parts in the box with the bill of materials provided to assure that you have all the parts necessary for this installation.
PAGE 2
Minimum Required Tool List: TOOLS: 1 3/8” Drive Ratchet 2 3/8” Drive Extension 3” 3 15mm Deep Well Socket 5 Pry Bar SHOP SUPPLIES: 1 Spray Lubricant Borla Performance Cat-Back™ Bill of Materials (PN-60556) ADAPTOR 157” wheelbase or (PN-60564) ADAPTOR 163” wheelbase 140617
PAGE 3
(PN-60556) ADAPTOR 157” wheelbase or (PN-60564) ADAPTOR 163” wheelbase 140618 (PN-60556) ADAPTOR 157” wheelbase or (PN-60564) ADAPTOR 163” wheelbase 140619
PAGE 4
(PN-60556) ADAPTOR 157” wheelbase (PN-60564) ADAPTOR 163” wheelbase
PAGE 5
Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Cat-Back™ Exhaust System. Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift.
PAGE 6
Borla Performance Cat-Back  Exhaust System Installation 1. Place Front Muffler Assembly using the original hardware. (See Fig. 5) Lightly tighten the bolts. 2. Place a clamp over the expanded end of the Mid Pipe Assembly and insert the inlet to the Front Muffler Assembly. Do not tighten the clamp. Figure 5 3. Install Adaptor Pipes 60556 or 60564 (if required). Place a clamp over the expanded end of the Extension Pipe and insert into outlet of the Front Muffler Assembly. Do not tighten the clamp. 4.