E2600 DSA E-Series iSCSI Disk Arrays en Quick Install Guide
E2600 DSA E-Series iSCSI Disk Arrays Table of Contents | en 3 Table of contents 1 Before you begin 4 1.1 Learn about management methods 4 1.
en | Before you begin 1 E2600 DSA E-Series iSCSI Disk Arrays Before you begin For warnings and detailed installation instructions, refer to the E2600 DSA E-Series Installation manual and additional documentation in the Online Product Catalog on http:// www.boschsecurity.com > Video > Digital Recording and Storage > Disk Arrays (Network Attached) > DSA – Disk Arrays > DSA E-Series iSCSI Disk Arrays. (The navigation path is subject to change).
E2600 DSA E-Series iSCSI Disk Arrays Before you begin | en – A cart to hold the controller-drive tray and its components – Labels for the cable connections – A medium flat-blade screwdriver – A No.
en | Device view 2 E2600 DSA E-Series iSCSI Disk Arrays Device view Controller-Drive Tray (12 Drives) – Front View 1 2 3 4 5 6 ! Figure 2.1: Front View E2600 1 Standby Power LED 4 Service Action Required LED 2 Power LED 5 Locate LED 3 Over-Temperature LED 6 Drive Canister 2 Power-Fan Canister Controller-Drive Tray – Rear View 1 2 Figure 2.
E2600 DSA E-Series iSCSI Disk Arrays 3 Install the mounting rails | en 7 Install the mounting rails You can install the drive tray into an industry-standard cabinet. There must be a minimum depth of 76 cm (30 in.) between the front EIA support rails and the rear EIA support rails. 1. Position the mounting rails in the cabinet. – If you are installing the mounting rails above an existing tray, position the mounting rails directly above the tray.
en | Install the controller-drive tray E2600 DSA E-Series iSCSI Disk Arrays Install the controller-drive tray 4 Warning! Risk of bodily injury ! , Two persons are required to safely lift the component. 1. With the help of one other person, remove the controller-drive tray from the shipping box. 2.
E2600 DSA E-Series iSCSI Disk Arrays 5 Secure the controller-drive tray | en 9 Secure the controller-drive tray Warning! Risk of bodily injury Do not use equipment in the cabinet as a shelf or work space. ! 1. Secure the screws in the top mounting holes and the bottom mounting holes on each side of the controller-drive tray. 2 1 2 1 Figure 5.1: Controller-Drive Tray (12 Drives) Mounting Holes 1 2.
en | Connect the cables 6 E2600 DSA E-Series iSCSI Disk Arrays Connect the cables Warning! ! Risk of exposure to laser radiation Do not disassemble or remove any part of a Small Form-factor Pluggable (SFP) transceiver because you might be exposed to laser radiation.
Connect the cables | en E2600 DSA E-Series iSCSI Disk Arrays 1 1 2 3 2 3 4 5 4 5 6 5. 11 7 Cable the drive trays as needed. For maximum redundancy and tray loss protection, see the following figure. Refer to Hardware Cabling for detailed information. Note: – The number of drive trays may vary as long as the maximum number of drives is not exceeded. – You can connect a combination of drive trays for a maximum of 192 drives, including the 12 drives in the E2600 controller-drive tray.
en | Connect the cables E2600 DSA E-Series iSCSI Disk Arrays Chamonix A A Contr oller Chamonix B Contr oller B Exp Exp SAS IN SAS IN SAS EXP SAS IN SAS IN SAS EXP ESM A ESM B 1A 1B 2A 2B SAS IN SAS IN SAS EXP SAS IN SAS IN SAS EXP ESM A ESM B 1A 1B 2A 2B SAS IN SAS IN SAS EXP SAS IN SAS IN SAS EXP ESM A ESM B 1A 1B 2A 2B SAS IN SAS IN SAS EXP SAS IN SAS IN SAS EXP ESM A ESM B 1A 1B 2A 2B SAS IN SAS IN SAS EXP SAS IN SAS IN SAS EXP ESM A ESM B 1A 1B 2A 2B SAS IN SAS IN SAS EXP S
E2600 DSA E-Series iSCSI Disk Arrays Turn on the DC power | en 13 Turn on the DC power 7 Notice! i DC power is an option that is available for use with your E2600 controller-drive tray and drive trays. If you choose to have –48 VDC power available, you need a qualified service person to install the equipment that provides special DC power connectors to each power-fan canister in your storage array.
en | Turn on the DC power E2600 DSA E-Series iSCSI Disk Arrays 2 1 You must follow the power sequence in the order shown. To establish power redundancy for trays with two power supplies, use a separate power source for each power-fan canister. For additional redundancy, you can connect each DC power connector on the same power-fan canister to a different power source. Notice! i You must turn on the power to all connected drive trays before you turn on the power to the E2600 controller-drive tray.
E2600 DSA E-Series iSCSI Disk Arrays Turn on the AC power | en 15 Turn on the AC power 8 2 1 You must follow the power sequence in the order shown for turning on AC power to controller-drive trays and drive trays that use AC power. To establish power redundancy for trays with two power supplies, use at least two different power distribution units (PDUs) in the cabinet. Split the power connections from each tray into the separate PDUs.
en | Install and configure the storage array 9 E2600 DSA E-Series iSCSI Disk Arrays Install and configure the storage array For the basic setup use the VRM Configuration Manager software. For detailed information refer to the Configuration Manager operating manual. For advanced features refer to the SANtricity configuration and installation manual. All necessary documentation can be found in the Online Product Catalog on http:// www.boschsecurity.
Bosch Sicherheitssysteme GmbH Robert-Bosch-Ring 5 85630 Grasbrunn Germany www.boschsecurity.