Plena Two-zone Call Station Installation and User Instructions en PLE-2CS
Plena Two-zone Call Station | Installation and User Instructions | Important safeguards Important safeguards Before installing or operating this product, always read the Safety Instructions, which are available as a separate document (9922 141 7014x). These instructions are supplied together with all equipment that can be connected to the mains.
Plena Two-zone Call Station | Installation and User Instructions | Table of contents en | 3 Table of contents Important safeguards ...................................................................................................................................................2 Table of contents ...........................................................................................................................................................3 1. Introduction .......................................
Plena Two-zone Call Station | Installation and User Instructions | Table of contents Intentionally left blank Bosch Security Systems | 2008-01 | PLE-2CS en en | 4
Plena Two-zone Call Station | Installation and User Instructions | Introduction 1 Introduction 1.1 Purpose The purpose of these Installation and User Instructions is to provide information that is required to install, configure and operate a Plena Two-zone Call Station. 1.2 1.6 Icons 1.6.1 Note icons The icons used in combination with Notes provide extra information about the Note. See the following examples: Digital document Note General icon for notes.
Plena Two-zone Call Station | Installation and User Instructions | Introduction 1.7 Conversion tables In this manual, SI units are used to express lengths, masses, temperatures etc. These can be converted to non-metric units using the following information. table 1.1: Conversion of units of length 1 in = 25.4 mm 1 mm = 1 in = 2.54 cm 1 cm = 1 ft = 0.3048 m 1m= 1 mi = 1.609 km 1 km = 0.03937 in 0.3937 in 3.281 ft 0.622 mi table 1.2: Conversion of units of mass 1 lb = 0.
Plena Two-zone Call Station | Installation and User Instructions | Description 2 Description 2.1 The Plena product range The Plena Two-zone Call Station is part of the Plena product range. Plena provides public address solutions for places where people gather to work, worship, trade, or relax.
Plena Two-zone Call Station | Installation and User Instructions | Description 2.4 2.4.1 Controls, connectors and indicators Top side See figure 2.1 for an overview of the controls and indicators on the top side of the call station: 1 Zone selection buttons - Two buttons to select the zones to which the business call is distributed. Each button has a green LED, which indicates the zone to which the business call is distributed.
Plena Two-zone Call Station | Installation and User Instructions | Installation 3 Installation 3.1 Unpack unit 1 Remove the unit from the box, and discard the packaging material according to local regulations. 2 Use your fingernails to carefully peel off the protective plastic film. Do not use sharp or pointed objects. 3.
Plena Two-zone Call Station | Installation and User Instructions | Installation Intentionally left blank Bosch Security Systems | 2008-01 | PLE-2CS en en | 10
Plena Two-zone Call Station | Installation and User Instructions | Connections 4 4.1 en | 11 Connections and settings 4.2 Connecting multiple call stations Use the DIP switches at the bottom of the call station to set the chime, the momentary or latching speaking function, the speech filter and the microphone gain. See figure 4.2. When the configuration requires more than one call station, use the loop-through RJ-45 sockets on the call stations to make loop-throughs.
Plena Two-zone Call Station | Installation and User Instructions | Connections 4.2.4 Microphone gain settings See figure 4.2. DIP switches number 6 and 7 are used for setting the microphone gain. 1 = ON-position, 0 = OFF-position. table 4.2: Microphone gain settings DIP switch setting Description (6-7) 0-0 -15 dB 1-0 0 dB 0-1 +6 dB 1-1 +6 dB 1 2 3 4 5 6 7 8 ON ON(1) DIP OFF(0) 1 2 3 4 5 6 7 8 (spare) figure 4.
Plena Two-zone Call Station | Installation and User Instructions | Operation 5 Operation 5.1 Make calls (momentary speaking function) 1 Press the push-to-talk button and keep the button depressed during the business call. 2 Make the business call. 3 Release the push-to-talk button after the business call. 5.2 Make calls (latching speaking function) 1 Shortly press the push-to-talk button to start the business call. 2 Make the business call.
Plena Two-zone Call Station | Installation and User Instructions | Operation Intentionally left blank Bosch Security Systems | 2008-01 | PLE-2CS en en | 14
Plena Two-zone Call Station | Installation and User Instructions | Technical data 6 6.1 Technical data Electrical Voltage range: 24 V(DC), supplied by PLE-series mixer or mixer amplifier. Current consumption: < 30 mA 6.2 Performance Nominal sensitivity: 85 dB SPL (gain preset 0 dB) Nominal output level: 700 mV Maximum input sound level: 110 dB SPL Gain preset: -15 / 0 / +6 dB Limiter threshold: 2V Compression ratio limiter: 1:20 Distortion: < 0.
Plena Two-zone Call Station | Installation and User Instructions | Technical data Intentionally left blank Bosch Security Systems | 2008-01 | PLE-2CS en en | 16
For more information visit www.boschsecuritysystems.com © Bosch Security Systems B.V.
