FLEXIDOME HD VR NIN-733 / NIN-832 / NIN-932 en Installation Manual
FLEXIDOME HD VR Table of Contents | en 3 Table of Contents 1 Safety 6 1.1 Safety precautions 6 1.2 Important safety instructions 7 1.3 Connection in applications 8 1.4 Type label 8 1.5 FCC & ICES compliance 1.6 MicroSD cards 10 9 1.7 UL certification 10 1.8 Bosch notices 11 1.9 Copyrights 12 2 Introduction 13 2.1 Features 13 3 System Information 14 3.1 Network video server 14 3.1.1 Progressive scan 14 3.1.2 True Day/Night function 14 3.1.
en | Table of Contents FLEXIDOME HD VR 5 Installation 19 5.1 Parts 19 5.2 Mounting the unit 20 5.2.1 Surface mounting 20 5.2.2 Flush mount 21 5.3 Connections 22 5.3.1 Make the connections 22 5.4 Mount the camera 25 5.5 Controls 26 5.6 Camera positioning and field-of-view 27 5.6.1 Pan 28 5.6.2 Tilt 28 5.6.3 Twist 29 5.7 Using the install wizard 30 5.7.1 Adjustment procedure 30 5.8 Closing the unit 31 6 Camera configuration 33 6.1 User modes 33 6.
FLEXIDOME HD VR 10.1.1 Table of Contents | en Dimensions Bosch Security Systems 5 47 Installation Manual AM18-Q0637 | v1.1 | 2013.
en | Safety FLEXIDOME HD VR 1 Safety 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
FLEXIDOME HD VR 1.2 Safety | en 7 Important safety instructions Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings on the unit and in the operating instructions before operating the unit. 1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. 2. Do not install unit near any heat sources such as radiators, heaters, stoves, or other equipment that produce heat. Avoid exposure to direct sunlight for long periods. 3.
en | Safety 1.3 FLEXIDOME HD VR Connection in applications Grounding The yellow/green safety (power) ground wire from the camera must be connected to the system earth of the installation. U.S.A.: - section 810 of the National Electrical Code, ANSI/NFPA No.70, provides information regarding proper grounding. 12 VDC / 24 VAC power source: This unit is intended to operate with a limited power source. The unit is intended to operate at either 12 VDC or 24 VAC (if PoE is not available).
FLEXIDOME HD VR 1.5 Safety | en 9 FCC & ICES compliance FCC & ICES Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
en | Safety 1.6 FLEXIDOME HD VR MicroSD cards Bosch Security systems recommends that local storage on microSD card should only be used for alarm recording and Automatic Network Replenishment (ANR) applications. To minimize the risk of loss of digital information, we recommend multiple, redundant recording systems, and a procedure to back up all digital information. 1.7 UL certification Disclaimer Underwriter Laboratories Inc.
FLEXIDOME HD VR 1.8 Safety | en 11 Bosch notices Video loss Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information. Optical elements Optical elements are sensitive and should be protected at all times.
en | Safety 1.9 FLEXIDOME HD VR Copyrights The firmware uses the fonts "Adobe-Helvetica-Bold-R-Normal-24-240-75-75-P-138-ISO10646-1" and "Adobe-Helvetica-Bold-RNormal--12-120-75-75-P-70-ISO10646-1" under the following copyright: Copyright 1984-1989, 1994 Adobe Systems Incorporated. Copyright 1988, 1994 Digital Equipment Corporation.
FLEXIDOME HD VR Introduction | en 2 Introduction 2.1 Features 13 The FLEXIDOME HD Vandal-Resistant (VR) IP Day/Night camera is a high-performance, surveillance color camera. The analog video output of the camera can be used simultaneously with an IP stream to allow operation in hybrid mode. The IP video stream uses H.264 compression technology to give clear images while reducing bandwidth and storage requirements. It is also ONVIF compliant to improve compatibility during system integration.
en | System Information FLEXIDOME HD VR 3 System Information 3.1 Network video server The camera incorporates a network video server. Its primary function is to encode video and control data for transmission over an IP network. With its H.264 encoding, it is ideally suited for IP communication and for remote access to digital video recorders and IP systems. The use of existing networks means that integration with CCTV systems or local networks can be achieved quickly and easily.
FLEXIDOME HD VR 3.1.5 System Information | en 15 Audio Two-way duplex audio is available in the unit for live voice communications or audio recording. 3.1.6 Alarm I/O The alarm input can be used to control the functionality of the unit. An alarm output can control external devices. 3.1.7 Tamper detection and motion detection The camera offers a wide range of configuration options for alarm signaling in the event of tampering with the camera.
en | System Information 3.1.12 FLEXIDOME HD VR Recording The camera can be used with an iSCSI server connected via the network to store long-term recordings, and with a local microSD card for shorter storage times and temporary recordings. 3.1.13 Configuration The camera can be configured using a browser on the local network (Intranet) or from the Internet. Similarly, firmware updates and rapid loading of device configurations are also possible.
FLEXIDOME HD VR 3.2 System Information | en 17 Operation with external systems The camera can be used with a variety of Bosch systems: – Bosch Video Management System – Bosch Video Client – Bosch Recording Station When connected to any of these systems, many of the camera configuration parameters are controlled by the system and not by the settings made via a web browser.
en | Planning FLEXIDOME HD VR 4 Planning 4.1 Unpacking Unpack carefully and handle the equipment with care.
FLEXIDOME HD VR 5 Installation | en 19 Installation CAUTION! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. 5.1 Parts The camera/housing unit consists of the following parts: 1. 2. 3. 4. Bosch Security Systems Surface Mount Box (some models only) Camera module and mounting base Inner liner Dome cover Installation Manual AM18-Q0637 | v1.1 | 2013.
en | Installation FLEXIDOME HD VR 5.2 Mounting the unit 5.2.1 Surface mounting 9.5 mm (0.375 in) Ø 8 m m 3x 3x PCD 123 mm (4.84 in) To mount the camera on the surface of a wall or ceiling: 1. Use the surface mount box as a template to mark the holes indicated in the drawing. The PCD is 123 mm (4.84 in). 2. Drill three holes with a diameter of 8 mm (0.3 in). 3. Insert the supplied plugs into the holes. 4. Attach the surface mount box securely using the three supplied screws. 5.
FLEXIDOME HD VR 5.2.2 Installation | en 21 Flush mount 105 (4.13) Ø 8 m m 3x 3x 57.6 (2.27) 66.5 (2.62) 33.3 (1.31) 57.6 (2.27) PCD: 133 (5.25) To flush mount the camera in a wall or ceiling: 1. Use the mounting template to mark out the recess and to mark the holes indicated in the drawing. The PCD is 133 mm (5.25 in) 2. Cut out the recess. 3. Drill three holes with a diameter of 8 mm (0.3 in). 4. Insert the supplied plugs into the holes. 5.
en | Installation 6. FLEXIDOME HD VR Using one of the keyholes, hang the mounting base of the camera module on one screw temporarily; tilt the base slightly to gain access to the cable connections. 7. 5.3 Make the connections as outlined in section 5.3 below. Connections CAUTION! Isolate unused power wires individually to prevent shortcircuits. Check the type label on the the camera module for the correct power ratings. 5.3.
FLEXIDOME HD VR Installation | en 23 Cable tree Use the following table to identify the wires in the cable tree: Wire color AWG Signal Red 26 +12 VDC / 24 VAC Brown 26 GND DC / 24 VAC Yellow / Green 24 Black / Orange 28 Alarm Out A White / Orange 28 Alarm Out B White / Violet 28 Ground (Alarm In) Orange / Violet 28 Alarm In 1 Violet 28 Alarm In 2 Earth White 28 Audio In (Shield) 28 Ground (Audio In) Black 28 Audio Out (Shield) 28 Ground (Audio Out) For connections u
en | Installation FLEXIDOME HD VR CAUTION! The RJ45 female-to-female network cable connector supplied is unshielded. To comply with the EMC Alarm immunity standard (EN 50130-4) or the EMC Railway immunity standard (EN 50121-4), a shielded twisted pair (STP) connection cable and a shielded RJ45 female-to-female network cable connector (not supplied) should be used. Analog video output Connect to the BNC connector to obtain an analog video signal.
FLEXIDOME HD VR Installation | en 25 intercom system. The audio input signal is transmitted in sync. with the video signal. Refer to the cable tree table to identify the wire colors for connecting the audio input and output. Audio in: Line input level (not suitable for direct microphone signal). Audio out: Line output level (not suitable for direct speaker connection). Wiring: Shielded audio connection cable is advised. 5.4 Mount the camera 1.
en | Installation 5.5 FLEXIDOME HD VR Controls 1. Reset button Restores the default IP address or restores a previous version of the firmware if uploading a new version fails. With the power on, use a small pointed object to press and hold the reset button for more than 10 seconds to restore the factory defaults. 2. Menu button Use this button to start the field-of view installation wizard. 3. MicroSD card slot Insert a microSD card into the slot. 4. Service video 2.
FLEXIDOME HD VR 5.6 Installation | en 27 Camera positioning and field-of-view The camera module position can be adjusted along three axes and several zoom positions can be selected. To help position the camera and set the field-of-view: 1. Connect a monitor to the 2.5 mm jack using the optional monitor cable (S1460) which provides a CVBS signal (for installation purposes only). 2. Apply power to the camera. 3. After power-up, wait a little (about 20 seconds). 4. Press the Menu button.
en | Installation 5.6.1 FLEXIDOME HD VR Pan For horizontal adjustment (pan): 1. Rotate the camera module (1) in the base. Do not rotate 2. Tighten the locking screw (2) with the supplied more than 180° in either direction. screwdriver bit. 5.6.2 Tilt For vertical adjustment (tilt): 1. Loosen the two thumbwheels (1). 2. Swing the camera module between the wings. Do not 3. Tighten the two thumbwheels (1). rotate more than 90°. ≤90° AM18-Q0637 | v1.1 | 2013.
FLEXIDOME HD VR 5.6.3 Installation | en 29 Twist To obtain a horizontal horizon (for tilted ceilings or sidewall mounting), twist the camera module to align the picture shown on the monitor. Bosch Security Systems Installation Manual AM18-Q0637 | v1.1 | 2013.
en | Installation 5.7 FLEXIDOME HD VR Using the install wizard The Menu button on the control panel is used to access the camera install wizard. When there is a choice in the wizard, the options are selected by either a short press (less than 2 s) or a long press (more than 2 s) of the button.
FLEXIDOME HD VR 1. Installation | en 31 To rotate the image 180°, press and hold the Menu button until the image flips. 2. Briefly press the Menu button to set the start position for the automatic motorized focus adjustment. – You will hear the motorized automatic back focus process running. – 3. The progress is shown on the monitor. Briefly press the Menu button again and again to scroll through the preset zoom positions. – The selection loops back to the beginning when you reach the last one.
en | Installation FLEXIDOME HD VR 1. Disconnect the service cable from the video jack. 2. Place the inner liner in position aligning its fin with the bracket on the base. 3. Using the supplied screwdriver bit, secure the dome bubble to the camera base by tightening the three screws. AM18-Q0637 | v1.1 | 2013.
FLEXIDOME HD VR 6 Camera configuration | en 33 Camera configuration The camera normally provides an optimal picture without the need for further adjustments. Configuration of the camera is carried out via the network using a web browser. 6.1 User modes The camera has six user modes. These modes contain optimized settings for a variety of applications. Select the mode most suited to the camera’s function via the web browser interface. 6.
en | Browser connection 7 FLEXIDOME HD VR Browser connection A computer with Microsoft Internet Explorer can be used to receive live images from the camera, control the camera, and replay stored sequences. The camera is configured over the network using the browser. The configuration options using the menu system of the camera itself are limited to setting up the lens and network. Note: The camera can also be configured using the supplied Bosch Video Client or the Bosch Video Management System. 7.
FLEXIDOME HD VR Troubleshooting | en 8 Troubleshooting 8.1 Function test 35 The camera offers a variety of configuration options. Therefore, check that it works properly after installation and configuration. This is the only way to ensure that the camera will function as intended in the event of an alarm.
en | Troubleshooting 8.2 FLEXIDOME HD VR Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution No image Defective camera. Connect a local monitor transmission to to the camera and check remote location. the camera function. Faulty cable connections. Check all cables, plugs, contacts and connections. No connection Incorrect encoder stream Select the H.
FLEXIDOME HD VR Troubleshooting | en 37 Malfunction Possible causes Solution No audio Hardware fault. Check that all connected transmission to audio units are operating remote station. correctly. Faulty cable connections. Check all cables, plugs, contacts and connections. Incorrect configuration. Check audio parameters on the Audio configuration and LIVEPAGE Functions pages.
en | Troubleshooting FLEXIDOME HD VR Malfunction Possible causes Solution Placeholder with a JVM not installed on your Install JVM on your red cross instead of computer or not computer. the ActiveX activated. components. Web browser Active proxy server in Create a rule in the local contains empty network. computer's proxy fields. settings to exclude local IP addresses. The POWER LED is Firmware upload failed. Repeat firmware upload. red. 8.
FLEXIDOME HD VR Maintenance | en 9 Maintenance 9.1 Testing the network connection 39 The ping command can be used to check the connection between two IP addresses. This allows testing whether a device is active in the network. 1. Open the DOS command prompt. 2. Type ping followed by the IP address of the device. If the device is found, the response appears as " Reply from ... ", followed by the number of bytes sent and the transmission time in milliseconds.
en | Maintenance 9.3 FLEXIDOME HD VR Repairs CAUTION! Never open the casing of the unit. The unit does not contain any user serviceable parts. Ensure that all maintenance or repair work is performed only by qualified personnel (electrical engineering or network technology specialists). In case of doubt, contact your dealer's technical service center. 9.3.1 Transfer and disposal The camera should only be passed on together with this installation guide.
FLEXIDOME HD VR Technical Data | en 10 Technical Data 10.1 Specifications 41 NIN-932 Imager 1/3-inch CMOS HD sensor Image resolution 1920 × 1080 pixels Rated supply voltage 24 VAC 50/60 Hz 12 VDC Power-over-Ethernet 48 VDC nominal Current consumption 600 mA (12 VDC) 500 mA (24 VAC) 175 mA (PoE 48 VDC) Minimum illumination 0.25 lx Color, 30 IRE Lens 3-9 mm, F1.2 0.08 lx Mono, 30 IRE Minimum illumination 0.45 lx Color, 30 IRE Lens 10-23 mm, F1.6 0.
en | Technical Data Lens type FLEXIDOME HD VR 3 to 9 mm or 10 to 23 mm varifocal SR (Super Resolution) Auto Varifocal (AVF) adjustment Automatic iris control Controls Via web browser or Configuration Manager User modes 6 pre-defined customizable user modes LAN interface STP, Ethernet 10/100 Base-T, auto-sensing, half/full duplex, RJ45 Video encoding H.264 (ISO/IEC 14496-10), M-JPEG protocols Stream (max.
FLEXIDOME HD VR Technical Data | en Memory card slot Supports SDHC and SDXC microSD cards Weight 0.84 kg (1.85 lb) Environment IP 66, NEMA Type 4X Impact protection IK10 Operating -30 °C to +50 °C (-22 °F to +122 °F) 43 temperature NIN-832 Imager 1/2.
en | Technical Data FLEXIDOME HD VR Privacy Masking Four independent areas, fully programmable Video Analysis Motion+, IVA versions Lens type 3 to 9 mm or 10 to 23 mm varifocal SR (Super Resolution) Auto Varifocal (AVF) adjustment Automatic iris control Controls Via web browser or Configuration Manager User modes 6 pre-defined customizable user modes LAN interface STP, Ethernet 10/100 Base-T, auto-sensing, half/full duplex, RJ45 Video encoding H.
FLEXIDOME HD VR Audio signal-to-noise Technical Data | en 45 > 50 dB ratio Memory card slot Supports SDHC and SDXC microSD cards Weight 0.84 kg (1.
en | Technical Data FLEXIDOME HD VR Sharpness Sharpness enhancement level selectable Privacy Masking Four independent areas, fully programmable Video Analysis Motion+, IVA versions Lens type 3 to 9 mm or 10 to 23 mm varifocal SR (Super Resolution) Auto Varifocal (AVF) adjustment Automatic iris control Controls Via web browser or Configuration Manager User modes 6 pre-defined customizable user modes LAN interface STP, Ethernet 10/100 Base-T, auto-sensing, half/full duplex, RJ45 Video enco
FLEXIDOME HD VR Audio standards Technical Data | en 47 AAC G.711, 8kHz sampling rate L16, 16kHz sampling rate Audio signal-to-noise > 50 dB ratio Memory card slot Supports SDHC and SDXC microSD cards Weight 0.84 kg (1.85 lb) Environment IP 66, NEMA Type 4X Impact protection IK10 Operating -30 °C to +50 °C (-22 °F to +122 °F) temperature 10.1.1 Dimensions Ø158 (6.22) 85 (3.35) 39 (1.54) Ø95 (3.7) mm (in) 141 (5.55) Ø158 (6.
en | Technical Data AM18-Q0637 | v1.1 | 2013.
Bosch Security Systems www.boschsecurity.
