DinionHD 1080p IP Camera NBN-832 en Installation Manual
DinionHD 1080p IP Camera Table of Contents | en 3 Table of Contents 1 Safety 6 1.1 Safety precautions 6 1.2 Important safety instructions 7 1.3 Connection in applications 8 1.4 FCC & ICES compliance 1.5 MicroSD cards 10 1.6 UL certification 10 1.7 Bosch notices 11 1.8 Copyrights 12 2 Introduction 13 2.1 Features 13 3 System Information 14 3.1 Overview of functions 14 3.1.1 Progressive scan 14 3.1.2 Day/Night function 14 3.1.3 Quad-streaming 14 9 3.1.
en | Table of Contents DinionHD 1080p IP Camera 4.2 System requirements 18 5 Installation 19 5.1 Lens mounting 19 5.2 Mounting the camera 21 5.3 Network (and power) connector 22 5.4 Power connector 23 5.5 Alarm and relay connector 24 5.6 Audio connectors 25 5.7 Local storage 26 5.8 Video service monitor connector 27 5.9 Data connector 28 6 Install Wizard 29 6.1 Using the camera install wizard 29 6.1.1 Adjustment procedure 30 7 Camera set-up 32 7.
DinionHD 1080p IP Camera Table of Contents | en 5 11 Technical Data 42 11.1 Specifications 42 Bosch Security Systems Installation Manual AM18-Q0600 | v1.0 | 2011.
en | Safety DinionHD 1080p IP Camera 1 Safety 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation.
DinionHD 1080p IP Camera 1.2 Safety | en 7 Important safety instructions Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings on the unit and in the operating instructions before operating the unit. 1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. 2. Do not install unit near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat. 3.
en | Safety 1.3 DinionHD 1080p IP Camera Connection in applications Grounding Safety (power) ground is indicated by the symbol on the rear of the camera. U.S.A.: - section 810 of the National Electrical Code, ANSI/NFPA No.70, provides information regarding proper grounding. 12 VDC / 24 VAC power source: This unit is intended to operate with a limited power source. The unit is intended to operate at either 12 VDC or 24 VAC (if PoE is not available).
DinionHD 1080p IP Camera 1.4 Safety | en 9 FCC & ICES compliance FCC & ICES Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
en | Safety 1.5 DinionHD 1080p IP Camera MicroSD cards Bosch Security systems recommends that local storage on microSD card should only be used for alarm recording and Automatic Network Replenishment (ANR) applications. To minimize the risk of lost of digital information, we recommend multiple, redundant recording systems, and a procedure to back up all digital information. 1.6 UL certification Disclaimer Underwriter Laboratories Inc.
DinionHD 1080p IP Camera 1.7 Safety | en 11 Bosch notices Video loss Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To minimize the risk of lost digital information, Bosch Security Systems recommends multiple, redundant recording systems, and a procedure to back up all analog and digital information. Optical elements Optical elements are sensitive and should be protected at all times.
en | Safety 1.8 DinionHD 1080p IP Camera Copyrights The firmware uses the fonts "Adobe-Helvetica-Bold-R-Normal-24-240-75-75-P-138-ISO10646-1" and "Adobe-Helvetica-Bold-RNormal--12-120-75-75-P-70-ISO10646-1" under the following copyright: Copyright 1984-1989, 1994 Adobe Systems Incorporated. Copyright 1988, 1994 Digital Equipment Corporation.
DinionHD 1080p IP Camera Introduction | en 2 Introduction 2.1 Features 13 The 1080p HD IP Day/Night camera is a high-performance, surveillance color camera. The camera uses H.264 compression technology to give clear images while reducing bandwidth and storage requirements. It is also ONVIF compliant to improve compatibility during system integration. The camera operates as a network video server and transmits video and control signals over data networks, such as Ethernet LANs and the Internet.
en | System Information DinionHD 1080p IP Camera 3 System Information 3.1 Overview of functions The camera incorporates a network video server. Its primary function is to encode video and control data for transmission over an IP network. With its H.264 encoding, it is ideally suited for IP communication and for remote access to digital video recorders and IP systems. The use of existing networks means that integration with CCTV systems or local networks can be achieved quickly and easily.
DinionHD 1080p IP Camera System Information | en 15 ONVIF standard is a global standard for the interface of network video products. 3.1.5 Audio Two-way duplex audio is available in the unit for live voice communications or audio recording. 3.1.6 Alarm I/O The alarm input can be used to control the functionality of the unit. An alarm output can control external devices. 3.1.
en | System Information 3.1.12 DinionHD 1080p IP Camera Encryption The unit offers a variety of options for protection against unauthorized reading. Web browser connections can be protected using HTTPS. Protect the control channels via the SSL encryption protocol. With an additional license, the user data itself can be encrypted. 3.1.
DinionHD 1080p IP Camera 3.2 System Information | en 17 Operation with external systems The camera can be used with a variety of Bosch systems: – Bosch Video Management System – Bosch Video Client – Bosch Recording Station When connected to any of these systems, many of the camera configuration parameters are controlled by the system and not by the settings made via a web browser.
en | Planning DinionHD 1080p IP Camera 4 Planning 4.1 Unpacking Unpack carefully and handle the equipment with care.
DinionHD 1080p IP Camera 5 Installation | en 19 Installation CAUTION! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. 5.1 Lens mounting The camera accepts CS or C-mount lenses. DC-iris lenses are recommended for best performance. The camera automatically detects the type of lens and optimizes performance accordingly. A spare male lens connector is provided. CAUTION! Lenses weighing more than 0.5 kg (1.
en | Installation DinionHD 1080p IP Camera Pin DC iris lens 1 Damp - 2 Damp + 3 Drive + 4 Drive - Note If a short circuit is detected on the lens connector, the lens circuit is automatically disabled to avoid internal damage. Remove the lens connector and check the pin connections. AM18-Q0600 | v1.0 | 2011.
DinionHD 1080p IP Camera 5.2 Installation | en 21 Mounting the camera The camera can be mounted either from the top or from the bottom (1/4" 20 UNC thread). 1/4”-20 UNC Figure 5.2 Mounting a camera CAUTION! Do not expose the image sensors to direct sunlight. Do not obstruct the free flow of air around the camera. Bosch Security Systems Installation Manual AM18-Q0600 | v1.0 | 2011.
en | Installation 5.3 DinionHD 1080p IP Camera Network (and power) connector 4 D A T A 5 6|4 5 6 A L A R M 1 2 3|1 2 3 E T H P o E µSD 22 - + 12VDC INSTALL 24VAC MENU STP Cat 5e RJ45 Ethernet (PoE) Figure 5.3 Network connection – Connect the camera to a 10/100 Base-T network. – Use STP Category 5e cable with RJ45 connectors (the camera network socket is Auto MDIX compliant).
DinionHD 1080p IP Camera 5.4 Installation | en 23 Power connector 5 mm 4 5 6|4 5 6 E T H P o E D A A L T A A R M 2 3|1 2 3 µSD 1 - + 12VDC INSTALL 24VAC MENU Earth Figure 5.4 Power connection Connect a SELV-LPS or a SELV Class 2 power supply with a rated supply voltage of 24 VAC or 12 VDC as follows: – Use AWG16 to 22 stranded wire or AWG16 to 26 solid wire; cut back 5 mm (0.2 in) of insulation.
en | Installation 5.5 DinionHD 1080p IP Camera Alarm and relay connector Alarm 4 5 6 5 mm (0.2 in) 1 2 Figure 5.5 3 Alarm and relay connector pins Pin Alarm socket 1 Alarm in 1 2 Alarm in 2 3 Relay out contact 1 4 Ground 5 Ground 6 Relay out contact 2 – Max. wire diameter AWG 22-28 for both stranded and solid; cut back 5 mm (0.2 in) of insulation. – Alarm output relay switching capability: Max voltage 30VAC or +40 VDC. Max 0.5 A continuous, 10 VA.
DinionHD 1080p IP Camera 5.6 Installation | en 25 Audio connectors 4 5 6|4 5 6 D A A L T A A R M 1 2 3|1 2 3 E T H P o E µSD GND - + Line 12VDC INSTALL 24VAC Figure 5.6 MENU Audio connectors Connect audio devices to the Audio In and Audio Out connectors. The unit has full-duplex mono audio. The two-way communication can be used to connect a speaker or door intercom system. The audio input signal is transmitted in sync. with the video signal.
en | Installation 5.7 DinionHD 1080p IP Camera Local storage 4 5 6|4 5 6 D A A L T A A R M 1 2 3|1 2 3 E T H P o E µSD 26 - + 12VDC INSTALL 24VAC Figure 5.7 MENU Inserting an microSD card 1. Unscrew the card slot cover. 2. Slide the microSD card into the slot until it locks in place. 3. Screw the cover into place to seal the slot. AM18-Q0600 | v1.0 | 2011.
DinionHD 1080p IP Camera 27 Video service monitor connector 4 D A T A 5 6|4 5 6 A L A R M 1 2 3|1 2 3 E T H P o E µSD 5.8 Installation | en - + 12VDC INSTALL 24VAC Figure 5.8 1. MENU Video service monitor connector Connect a service monitor to the composite video connector (INSTALL) to aid installation. 2. Press the menu button for longer than 2 seconds (after power-up, first wait 20 seconds). This stops the IP video stream and enables the video analog output.
en | Installation 5.9 DinionHD 1080p IP Camera Data connector 4 Data 5 6 5 mm (0.2 in) 1 2 3 Figure 5.9 Data connector pins Pin Data socket 1 Ground 2 RxD / Rx+ 3 CTS / Rx- 4 Ground 5 TxD / Tx- 6 RTS / Tx+ The data connector is used to connect the control data coming out of the camera to external devices. RS485, RS422, and RS232 is supported by this data connection.
DinionHD 1080p IP Camera Install Wizard | en 6 Install Wizard 6.1 Using the camera install wizard 29 The Menu button on the rear panel is used for accessing the camera install wizard. When there is a choice in the wizard, the options are selected by either a short press or a longer press of the button. 4 5 6|4 5 6 E T H P o E D A A L T A A R M 2 3|1 2 3 µSD 1 - + MENU 12VDC INSTALL 24VAC Figure 6.
en | Install Wizard 6.1.1 DinionHD 1080p IP Camera Adjustment procedure A monitor must be connected to the video service connector to use the wizard. (After power-up, wait 20 seconds before attempting to open the install wizard.) Focus Focal length Figure 6.2 1. Lens adjustment Briefly press the Menu button to start the wizard. – You see the following on the monitor screen: Lens type MBF feedback Auto MBF 180° MBF info – The lens type is identified and shown on the screen.
DinionHD 1080p IP Camera 5. Install Wizard | en 31 Briefly press the Menu button to start the automatic motorized (Auto MBF) back focus adjustment. – You will hear the motorized automatic back focus process running. – 6. The progress is shown on the monitor. If the camera is not correctly focussed, press the Menu button for a longer time to restart the wizard. 7. If the camera is correctly focussed, briefly press the Menu button. – The back focus position is stored.
en | Camera set-up 7 DinionHD 1080p IP Camera Camera set-up The camera normally provides an optimal picture without the need for further adjustments. Configuration of the camera is carried out via the network using a web browser. The camera has a set-up menu in which basic installation settings (lens wizard, IP address) can be accessed. To view this menu, connect a laptop to the network connection of the camera. 7.
DinionHD 1080p IP Camera 7.2 Camera set-up | en 33 Day/Night switching The camera is equipped with a motorized IR filter. The mechanical IR filter is taken out of the optical path in low-light applications. The IR filter is controlled either: – via an alarm input, or – automatically, based on the observed light levels. If Auto switching mode is selected, the camera automatically switches the filter depending on the observed light level. The switching level is programmable.
en | Browser connection 8 DinionHD 1080p IP Camera Browser connection A computer with Microsoft Internet Explorer can be used to receive live images from the camera, control the camera, and replay stored sequences. The camera is configured over the network using the browser. The configuration options using the menu system of the camera itself are limited to setting up the lens and network.
DinionHD 1080p IP Camera Troubleshooting | en 9 Troubleshooting 9.1 Function test 35 The camera offers a variety of configuration options. Therefore, check that it works properly after installation and configuration. This is the only way to ensure that the camera will function as intended in the event of an alarm.
en | Troubleshooting 9.2 DinionHD 1080p IP Camera Resolving problems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution No image Defective camera. Connect a local monitor transmission to to the camera and check remote location. the camera function. Faulty cable connections. Check all cables, plugs, contacts and connections. No connection Incorrect encoder stream Select the H.
DinionHD 1080p IP Camera Troubleshooting | en 37 Malfunction Possible causes Solution No audio Hardware fault. Check that all connected transmission to audio units are operating remote station. correctly. Faulty cable connections. Check all cables, plugs, contacts and connections. Incorrect configuration. Check audio parameters on the Audio configuration and LIVEPAGE Functions pages.
en | Troubleshooting DinionHD 1080p IP Camera Malfunction Possible causes Solution The unit is not Power failure during Have the unit checked by operational after a programming by firmware Customer Service and firmware upload. file. replace if necessary. Incorrect firmware file. Enter the IP address of the unit followed by / main.htm in your Web browser and repeat the upload.
DinionHD 1080p IP Camera Maintenance | en 10 Maintenance 10.1 Testing the network connection 39 The ping command can be used to check the connection between two IP addresses. This allows testing whether a device is active in the network. 1. Open the DOS command prompt. 2. Type ping followed by the IP address of the device. If the device is found, the response appears as " Reply from ... ", followed by the number of bytes sent and the transmission time in milliseconds.
en | Maintenance DinionHD 1080p IP Camera Configuring the Terminal Before the terminal program can communicate with the camera, the transmission parameters must be matched. Make the following settings for the terminal program: – 19,200 bps – 8 data bits – No parity check – 1 stop bit – No protocol Command Inputs After the connection has been established, you must log on to the camera to access the main menu. Other submenus and functions can be accessed using the on-screen commands. 1.
DinionHD 1080p IP Camera Maintenance | en 41 Note: You must reboot to activate the new IP address, a new subnet mask or a gateway IP address. Reboot Briefly interrupt the power supply to the camera for a reboot (disconnect the power supply unit from the mains supply and switch on again after a few seconds). Additional Parameters You can use the terminal program to check other basic parameters and modify them where necessary. Use the onscreen commands in the various submenus to do this. 10.
en | Technical Data DinionHD 1080p IP Camera 11 Technical Data 11.1 Specifications Imager 1/2.7-inch CMOS HD sensor Rated supply voltage 12 VDC, 400 mA (IVA: 500 mA) 24 VAC, 350 mA (IVA: 450 mA), 50/60 Hz PoE 48 VDC, 150 mA (IVA: 175 mA) Minimum illumination 0.5 lx color, 30 IRE 0.
DinionHD 1080p IP Camera Video encoding Technical Data | en 43 H.264 (ISO/IEC 14496-10), M-JPEG protocols Image resolutions 1920 × 1080 pixels Group of pictures IP, IBP, IBBP Network protocols HTTP, HTTPs, SSL, TCP, UDP, ICMP, RTSP, RTP, Telnet, IGMPv2/v3, SMTP, SNTP, FTP, DHCP client, ARP, DNS, DDNS, NTP, SNMP, UPnP, 802.1X, iSCSI Encryption TLS 1.0, SSL, AES (optional) Alarm input (2) Non-isolated closing contact TTL logic, +5V nominal, +40 VDC max, DC coupled with 22 kOhm pull-up to +3.
en | Technical Data AM18-Q0600 | v1.0 | 2011.
Bosch Security Systems www.boschsecurity.