Use and Care
Table Of Contents
- en Instruction manual 2
- en Table of contents
- en Instruction manual
- 8 Intended use 6
- 7 Environmental protection 6
- 5 Installation and connection 7
- * Getting to know your appliance 10
- 1 Operating the appliance 15
- o Home Connect 17
- M Alarm 19
- U Refrigerator compartment 19
- W Freezer compartment 20
- = Defrosting 21
- D Cleaning 21
- l Odors 22
- 9 Lighting 22
- > Noises 22
- 3 Faults – what to do? 23
- 4 Customer service 25
- ( Important safety instructions
- Important safety instructions
- READ INSTRUCTIONS - DO NOT DISCARD!
- Definitions
- 9 WARNING
- 9 CAUTION
- NOTICE:
- Note:
- About these instructions
- Introduction
- Risk of explosion
- Risk of electric shock
- Risk of cold burns
- Risk of Injury
- Risk of fire
- Avoiding placing children and vulnerable people at risk
- Risk of suffocation
- Damage
- Weight
- State of California Proposition 65 Warnings
- 8 Intended use
- 7 Environmental protection
- 5 Installation and connection
- Saving energy
- If you follow the instructions below, your appliance will use less power.
- Note:
- The arrangement of the fittings does not affect the energy consumption of the appliance.
- Installing the appliance
- Using the appliance
- --------
- Before using for the first time
- 1. Remove information material, adhesive tape and protective foil.
- 2. Clean the appliance. ~ "Cleaning" on page 21
- Water connection
- 9 CAUTION
- Water pressure of drinking water system
- 9 CAUTION
- Note:
- Electrical connection
- 9 CAUTION
- Note:
- 1. After installing the appliance, wait at least 1 hour before connecting it to prevent damaging the compressor.
- 2. Check that the outlet was installed according to the regulations and complies with the requirements.
- Requirements for outlets
- Maximum simultaneous load
- 3. Connect the appliance to an outlet near the appliance.
- 9 WARNING
- Risk of electric shock!
- 9 WARNING
- Risk of electric shock!
- * Getting to know your appliance
- Getting to know your appliance
- 2-door appliance
- 3-door appliance
- Operating controls
- Mode selection
- Eco mode
- Vacation mode
- Sabbath mode
- Settings
- Language
- Home Connect
- Tones
- Display brightness
- Temperature unit
- Ice cube production
- Water filter counter
- Factory settings
- Self-test
- Condensation protection (only on 3-door appliances)
- Demo mode
- Note:
- Interior fittings
- Storage compartment
- 1. Lift up the storage compartment and remove.
- 2. When re-inserting, insert hooks on back of storage compartment at same height to make it level.
- Note:
- Shelf
- 1. Lift shelf and remove.
- 2. When re-inserting, insert hooks on back of shelf at same height to make it level.
- Note:
- Container
- Ice pack
- Note:
- Ice maker
- 9 CAUTION
- Damage to the appliance!
- Notes
- Water filter
- Note:
- Exchange water filter or replace with bypass cartridge
- Note:
- 1. Turn the cap of the water filter counter-clockwise.
- 2. Take the water filter out.
- 3. Remove the protective cap of the new water filter or the new bypass cartridge.
- 4. Take off the cap of the used water filter and put it on the new water filter or bypass cartridge.
- 5. Slide the new water filter or bypass cartridge to the stop in the filter opening.
- Note:
- 6. Turn the water filter or bypass cartridge clockwise to the mark.
- Note:
- 7. When installing a water filter: reset water filter counter. ~ "Water filter counter" on page 12
- 8. Discard ice cubes produced over the first 24 hours.
- 9. Drain the water out of the used water filter.
- Note:
- 1 Operating the appliance
- Operating the appliance
- Switching the appliance on
- 1. Press the main On/Off switch.
- 2. Set the required temperature. ~ "Setting the temperature" on page 15
- Operating tips
- Switching off and disconnecting the appliance
- Switching off the appliance
- Disconnecting the appliance
- 9 CAUTION
- 1. Turn off the water supply to the appliance and wait 3 hours.
- 2. Remove groceries.
- 3. Press the main On/Off switch.
- 4. Pull out the mains plug or switch off the fuse.
- 5. Empty the ice cube container and clean the appliance. ~ "Cleaning" on page 21
- 6. Leave appliance open.
- Setting the temperature
- Recommended temperature
- Setting the refrigerator and freezer compartment temperature
- 1. Select the required compartment by tapping the temperature display.
- 2. Move the displayed temperature to the required value.
- 3. Return to the main screen with the x button.
- Super cooling
- Note:
- Switching super cooling on or off
- 1. Select the refrigerator compartment by tapping the temperature display.
- 2. Tap ] button.
- 3. Tap Continue.
- Note:
- Super freezing
- Note:
- Switching super freezing on or off
- 1. Select the freezer compartment by tapping the temperature display.
- 2. Tap ] button.
- 3. Tap Continue.
- Note:
- Eco mode
- Vacation mode
- Sabbath mode
- Switching ice cube production on or off
- 9 CAUTION
- Note:
- Switching Prevent condensation on or off
- 9 CAUTION
- o Home Connect
- Home Connect
- Note:
- Note:
- Setting up Home Connect
- Notes
- 1. Install the app.
- 2. Connect your refrigerator to the home WLAN network (Wi-Fi).
- 3. Connect the refrigerator to the Home Connect app.
- Setting up the connection to the home network (WLAN)
- 1. Install the Home Connect app on your mobile device.
- 2. Open the Home Connect menu on your refrigerator.
- 3. Open the app on your mobile device.
- 4. Log in or register with the app if access is not yet available.
- 5. Check the router of your home network to see if a WPS function is available for automatic connection.
- 6. If this function is available, start automatic network connection and follow the instructions on the control panel.
- 7. Start manual network connection if this function is not available, if you're not sure whether the function is available, or if automatic network connection failed.
- 8. Start manual network connection in the app of your mobile device.
- Note:
- Verifying signal strength
- Improving signal strength
- Connecting the refrigerator to the Home Connect app
- 1. Install the Home Connect app on your mobile device and log in or register.
- 2. Open the Home Connect menu on your refrigerator.
- 3. Tap menu item Connect to app.
- 4. Confirm the prompt to display the refrigerator in the app.
- 5. Open the app and wait until the refrigerator is displayed. Press Add to confirm the connection between the app and the refrigerator.
- 6. Follow the instructions in the app until the process is complete.
- Installing updates for the Home Connect software
- 1. Open the Home Connect menu.
- 2. Tap Software update.
- Note:
- 3. To install the update, tap Install now.
- Customer Service access
- 1. Contact Customer Service. ~ "Customer service" on page 25
- 2. Confirm the start of Customer Service access in the app.
- 3. As soon as Customer Service has obtained the necessary data, they end access.
- Note:
- Reset settings
- 1. Open the Home Connect menu on your refrigerator.
- 2. Tap the menu item Reset settings.
- 3. Confirm the prompt to delete the network settings.
- Switch on or off the connection to the home WLAN network (Wi-Fi)
- 1. Open the Home Connect menu on your refrigerator.
- Note:
- 2. Select Switch off Wi-Fi.
- 3. To start the switching off process, press Continue.
- 4. As soon as the connection to the home network has been switched off, the message Wi-Fi switched off will appear. Press OK to confirm the message.
- Note:
- Information on data protection
- Note:
- M Alarm
- U Refrigerator compartment
- W Freezer compartment
- Freezer compartment
- Fully utilizing the freezer volume
- Purchasing frozen food
- When loading products
- Freezing fresh food
- Suitable for freezing
- Not suitable for freezing
- Packing frozen food
- 1. Place food in packaging.
- 2. Remove air.
- 3. Pack food airtight to prevent it from losing flavor or drying out.
- 4. Label packaging with contents and date of freezing.
- Shelf life of frozen food at 0 °F (-18 °C)
- Thawing frozen food
- 9 CAUTION
- = Defrosting
- D Cleaning
- Cleaning
- 9 CAUTION
- Avoid damaging the appliance and the fittings.
- Cleaning the display
- Cleaning the appliance interior
- 1. Press the main On/Off switch.
- 2. Take out food and store in a cool location.
- 3. Clean the appliance with a soft cloth, lukewarm water and a little pH-neutral washing-up liquid.
- 9 CAUTION
- 4. Wipe door seal with clear water and dry thoroughly with a cloth.
- 5. Switch appliance back on and put in food.
- Cleaning the fittings
- Care instructions for stainless steel surfaces
- l Odors
- Odors
- 1. Switch off the appliance with the main On/Off switch.
- 2. Take all food out of the appliance.
- 3. Clean the inside. ~ "Cleaning" on page 21
- 4. Clean all packaging.
- 5. Seal strong-smelling food in order to prevent odors from forming.
- 6. Switch the appliance on again.
- 7. Store food in the appliance.
- 8. Check whether the formation of odors is still occurring after 24 hours.
- 9. Change the odor filter. ~ "Changing the odor filter" on page 22
- Changing the odor filter
- 1. Open the filter holder with a slotted screwdriver.
- 2. Remove the used odor filter and replace with a new odor filter.
- 3. Close the filter holder.
- 9 Lighting
- > Noises
- 3 Faults – what to do?
- Before you call customer service, use this table to check whether you can rectify the fault yourself.
- Appliance
- Ice maker
- The ice maker is not functioning.
- Too few or deformed ice cubes, water pressure lower than usual.
- Water is leaking out of the appliance.
- --------
- 4 Customer service
- Customer service
- Appliance self-test
- 1. Press Ò button to open the settings.
- 2. Tap the menu item Self-test.
- 3. Tap Start.
- 4. If faults are present, they will be displayed. In this case, follow the instructions on the display.
- 5. The appliance restarts.
- 6. A message that the self-test has finished is displayed for 10 seconds.
- Repair order and advice on faults
- 4 Customer service
- en Instruction manual
- fr Table des matières
- fr Notice d'utilisation
- 8 Utilisation conforme 30
- 7 Protection de l'environnement 30
- 5 Installation et branchement 31
- * Présentation de l’appareil 34
- 1 Utiliser l'appareil 39
- o Home Connect 41
- M Alarme 43
- U Compartiment réfrigérateur 43
- W Compartiment congélateur 44
- = Dégivrer l’appareil 46
- D Nettoyage 46
- l Odeurs 47
- 9 Éclairage 47
- > Bruits 47
- 3 Que faire en de problème. 48
- 4 Service à la clientèle 50
- ( Consignes de sécurité importantes
- Consignes de sécurité importantes
- VEUILLEZ LIRE ET CONSERVER CES CONSIGNES!
- Définitions
- 9 AVERTISSEMENT
- 9 ATTENTION
- AVIS :
- Remarque :
- À propos de cette notice
- Introduction
- Risque d’explosion
- Risque d’électrocution
- Risque d'engelures provoquées par le froid
- Risque de blessure
- Risque d’incendie
- Sécurité des enfants et des personnes à risque
- Risque d’asphyxie
- Dégâts matériels
- Poids
- Avertissements de la Proposition 65 de l’État de la Californie
- 8 Utilisation conforme
- 7 Protection de l'environnement
- Protection de l'environnement
- Emballage
- Appareil usagé
- 9 AVERTISSEMENT
- Les enfants risque de s'enfermer dans l'appareil et de s'asphyxier. !
- 9 ATTENTION
- Le fluide frigorigène et des gaz nocifs peuvent se dégager.
- 1. Débranchez la fiche de contact de la prise de courant.
- 2. Coupez le câble de raccordement secteur.
- 3. Acheminez l'appareil au service d'élimination approprié.
- 5 Installation et branchement
- Économiser de l’énergie
- Si vous respectez les instructions suivantes, votre appareil consommera moins de courant.
- Remarque :
- L’agencement des pièces d’équipement n’a aucune influence sur la consommation d’énergie de l’appareil.
- Installer l’appareil
- Utilisation de l'appareil
- --------
- Avant la première utilisation
- 1. Retirez la documentation informative, les rubans adhésifs et la feuille protectrice.
- 2. Nettoyez l’appareil. ~ "Nettoyage" à la page 46
- Raccordement de l’eau
- 9 ATTENTION
- Pression hydraulique de la conduite d'eau potable.
- 9 ATTENTION
- Remarque :
- Connexion électrique
- 9 ATTENTION
- Remarque :
- 1. Après l'installation de l'appareil, attendez au moins 1 heure avant de le raccorder afin d'éviter d'endommager le compresseur.
- 2. Assurez-vous que la prise murale est correctement installée et satisfait aux critères.
- Critères pour la prise murale
- Charge maximale simultanée
- 3. Raccordez l'appareil à une prise à proximité.
- 9 AVERTISSEMENT
- Risque d’électrocution !
- 9 AVERTISSEMENT
- Risque d’électrocution !
- * Présentation de l’appareil
- Présentation de l’appareil
- Appareil à 2 portes
- Appareil à 3 portes
- Éléments de commande
- Sélect. mode opération
- Mode éco
- Mode Vacances
- Mode Sabbat
- Réglages
- Langue
- Home Connect
- Sons
- Luminosité de l'afficheur
- Unité de température
- Production cubes de glace
- Compteur filtre à eau
- Paramètres d'usine
- Autodiagnostic
- Protect. anti-condens. (exclusif à l'appareil à 3 portes)
- Mode démo
- Remarque :
- Équipement
- Support
- 1. Soulevez les compartiments et retirez-les.
- 2. Pour remettre un compartiment en place, positionnez les crochets à l'arrière de celui-ci à la même hauteur afin que le compartiment soit bien droit.
- Remarque :
- Clayette
- 1. Soulevez la clayette et retirez-la.
- 2. Pour la remettre en place, positionnez les crochets à l'arrière de la clayette à la même hauteur afin qu'elle soit bien droite.
- Remarque :
- Bac
- Accumulateurs de froid
- Remarque :
- Distributeur de glaçons
- 9 ATTENTION
- Dommages à l'appareil!
- Remarques
- Filtre à eau
- Remarque :
- Remplacer le filtre à eau par un neuf ou par une cartouche filtrante avec dérivation
- Remarque :
- 1. Faire tourner le bouchon du filtre à eau dans le sens antihoraire.
- 2. Retirer le filtre à eau.
- 3. Retirer le bouchon de protection du nouveau filtre à eau ou de la nouvelle cartouche filtrante avec dérivation.
- 4. Retirer le bouchon du filtre à eau usé et le poser sur le nouveau filtre à eau ou sur la nouvelle cartouche filtrante avec dérivation.
- 5. Enfoncer le nouveau filtre à eau ou la nouvelle cartouche filtrante avec dérivation dans l’ouverture jusqu’en butée.
- Remarque :
- 6. Tourner le filtre à eau ou la cartouche filtrante avec dérivation dans le sens des aiguilles d’une montre jusqu’au repère.
- Remarque :
- 7. Au même moment où le filtre à eau est posé : réinitialiser le compteur du filtre à eau. ~ "Compteur filtre à eau" à la page 36
- 8. Jeter tous les glaçons formés durant les 24 premières heures.
- 9. Vider l'eau dans le filtre à eau usé.
- Remarque :
- 1 Utiliser l'appareil
- Utiliser l'appareil
- Allumer l’appareil
- 1. Actionner l'interrupteur principal marche/arrêt.
- 2. Régler la température souhaitée. ~ "Régler la température" à la page 39
- Remarques concernant le fonctionnement de l’appareil
- Arrêter et remiser l’appareil
- Éteindre l’appareil
- Éteindre l’appareil
- 9 ATTENTION
- 1. Coupez l'arrivée d'eau à l'appareil et attendez 3 heures.
- 2. Retirez les aliments de l'appareil.
- 3. Appuyez sur l’interrupteur principal Marche / Arrêt.
- 4. Débranchez la fiche de contact de la prise de courant ou ramenez le disjoncteur en position éteinte.
- 5. Videz le bac à glaçons et nettoyez-le. ~ "Nettoyage" à la page 46
- 6. Laissez l'appareil ouvert.
- Régler la température
- Température recommandée
- Régler la température des compartiments réfrigérateur et congélateur
- 1. Choisissez le compartiment souhaité en le touchant à l'écran d'affichage des températures.
- 2. Réglez la température affichée à la valeur souhaitée.
- 3. Retournez à l'écran principal avec la touche x.
- Super-réfrigération
- Remarque :
- Activer ou désactiver la super-refrigération
- 1. Choisissez le compartiment réfrigérateur en le touchant à l'écran d'affichage des températures.
- 2. Appuyez sur la touche ].
- 3. Appuyez sur Poursuivre.
- Remarque :
- Supercongélation
- Remarque :
- Activer ou désactiver la super-congélation
- 1. Choisissez le compartiment réfrigérateur en le touchant à l'écran d'affichage des températures.
- 2. Appuyez sur la touche ].
- 3. Appuyez sur Poursuivre.
- Remarque :
- Mode éco
- Mode Vacances
- Mode Sabbat
- Lancer et arrêter la production de glaçons
- 9 ATTENTION
- Remarque :
- Activer ou désactiver la protection anti- condensation
- 9 ATTENTION
- o Home Connect
- Home Connect
- Remarque :
- Remarque :
- Configurer Home Connect
- Remarques
- 1. Installez l'application.
- 2. Connectez le réfrigérateur au réseau domestique WLAN (Wi-Fi).
- 3. Connectez le réfrigérateur à l'application Home Connect.
- Configuration de la connexion au réseau domestique (WLAN)
- 1. Installez l'application Home Connect sur votre terminal mobile.
- 2. Ouvrez le menu Home Connect sur le réfrigérateur.
- 3. Ouvrez l'application sur le terminal mobile.
- 4. Connectez-vous à l'application ou enregistrez- vous si vous ne disposez pas encore d'un accès.
- 5. Vérifiez si le routeur de votre réseau domestique comporte une fonction WPS pour la connexion automatique.
- 6. Si cette fonction est présente, lancez la connexion automatique au réseau avec et suivez les instructions sur le panneau de commande.
- 7. Lancez une connexion manuelle au réseau si cette fonction n'est pas présente, si vous avez un doute quant à sa présence ou en cas d'échec de la connexion automatique.
- 8. Lancez la connexion manuelle au réseau dans l'application du terminal mobile.
- Remarque :
- Contrôler l'intensité du signal
- Améliorer l'intensité du signal
- Connecter le réfrigérateur à l’application Home Connect
- 1. Installez l’application Home Connect sur votre terminal mobile et connectez ou enregistrez-vous.
- 2. Ouvrez le menu Home Connect sur le réfrigérateur.
- 3. Appuyez sur le point de menu Connecter avec l'appli.
- 4. Confirmez le message pour afficher le réfrigérateur dans l’application.
- 5. Ouvrez l’application et attendez que le réfrigérateur s’affiche. Confirmez la connexion entre l’application et le réfrigérateur en appuyant sur Ajouter.
- 6. Suivez les instructions de l’application jusqu’à la fin de l’opération.
- Installer une mise à jour du logiciel Home Connect
- 1. Ouvrez le menu Home Connect.
- 2. Appuyez sur Mise à jour du logiciel.
- Remarque :
- 3. Pour installer la mise à jour, appuyez sur Installer maintenant.
- Accès au service à la clientèle
- 1. Contactez le service à la clientèle. ~ "Service à la clientèle" à la page 50
- 2. Confirmez le début de l’accès du service à la clientèle sur votre appareil dans l’application.
- 3. Dès que le service à la clientèle a collecté les informations nécessaires, il termine l’accès.
- Remarque :
- Réinitialiser les réglages
- 1. Ouvrez le menu Home Connect sur le réfrigérateur.
- 2. Appuyez sur le point de menu Réinitialiser les réglages.
- 3. Confirmez le message pour supprimer les paramètres réseau.
- Activer ou désactiver la connexion au réseau domestique WLAN (Wi-Fi)
- 1. Ouvrez le menu Home Connect sur le réfrigérateur.
- Remarque :
- 2. Choisissez Désactiver le Wi-Fi.
- 3. Pour lancer la désactivation, appuyez sur Poursuivre.
- 4. Une fois la connexion au réseau domestique interrompue, le message Wi-Fi éteint apparaît. Confirmer le message avec OK.
- Remarque :
- Remarque sur la protection des données
- Remarque :
- M Alarme
- U Compartiment réfrigérateur
- W Compartiment congélateur
- Compartiment congélateur
- Utiliser l’intégralité du volume de congélation
- Achats de produits surgelés
- Consignes de rangement
- Congeler des produits frais
- Vont au congélateur
- Ne vont pas au congélateur
- Emballer les surgelés
- 1. Placez les aliments dans l’emballage.
- 2. Pressez pour chasser l’air.
- 3. Fermez hermétiquement l'emballage afin que les produits alimentaires ne perdent pas leur goût ou ne sèchent pas.
- 4. Indiquez sur l’emballage le contenu et la date de congélation.
- Durée de conservation des aliments congelés à – 18 °C
- Décongélation des produits
- 9 ATTENTION
- = Dégivrer l’appareil
- D Nettoyage
- Nettoyage
- 9 ATTENTION
- Évitez d'endommager l'appareil et ses pièces d'équipement.
- Nettoyer l'écran
- Nettoyer le compartiment intérieur de l'appareil
- 1. Appuyez sur l’interrupteur principal Marche / Arrêt.
- 2. Sortez les produits alimentaires et rangez-les dans un endroit frais.
- 3. Ne nettoyez l’appareil qu’avec un chiffon doux, de l’eau tiède et du produit à vaisselle présentant un pH neutre.
- 9 ATTENTION
- 4. Essuyez le joint de porte avec de l'eau claire et frottez soigneusement pour le sécher.
- 5. Raccordez à nouveau l'appareil, mettez-le sous tension et rangez les produits alimentaires.
- Nettoyer l’équipement
- Consignes d'entretien pour les surfaces en inox
- l Odeurs
- Odeurs
- 1. Mettez l’appareil hors tension par l’interrupteur principal.
- 2. Sortez tous les produits alimentaires de l’appareil.
- 3. Nettoyez le compartiment intérieur. ~ "Nettoyage" à la page 46
- 4. Nettoyez tous les emballages.
- 5. Pour empêcher l’apparition d’odeurs, emballez hermétiquement les produits dont émane une odeur forte.
- 6. Remettez l’appareil en marche.
- 7. Remplissez l’appareil de nouveau.
- 8. Au bout de 24 heures, vérifiez si les odeurs persistent.
- 9. Changez le filtre à odeurs. ~ "Changez le filtre à odeurs" à la page 47
- Changez le filtre à odeurs
- 1. Ouvrez le compartiment de filtre avec un tournevis plat.
- 2. Extrayez le filtre à odeurs épuisé et mettez un filtre à odeurs neuf en place.
- 3. Fermez le compartiment de filtre.
- 9 Éclairage
- > Bruits
- 3 Que faire en de problème.
- Avant d’appeler le service à la clientèle, veuillez vérifier si le tableau ci-dessous ne contient pas déjà la solution qu'il vous faut.
- Appareil
- Distributeur de glaçons
- Le distributeur de glaçons ne fonctionne pas.
- Les glaçons sont déformés ou trop peu nombreux, la pression de l'eau est inhabituellement faible.
- De l’eau s'écoule de l’appareil.
- --------
- 4 Service à la clientèle
- Service à la clientèle
- Autodiagnostic de l’appareil
- 1. Appuyez sur la touche Ò pour ouvrir le menu Paramètres.
- 2. Appuyez sur le point de menu Autodiagnostic.
- 3. Appuyez sur Démarrer.
- 4. Toutes les erreurs constatées seront affichées à l'écran. Suivez les instructions à l'écran le cas échéant.
- 5. L'appareil redémarre.
- 6. Pendant 10 secondes, l'écran indiquera que l'autodiagnostic est terminé.
- Commande de réparation et conseils en cas de problèmes
- 4 Service à la clientèle
- fr Notice d'utilisation
- es Índice
- es Instrucciones de uso
- 8 Uso previsto 55
- 7 Protección del medio ambiente 55
- 5 Instalación y conexión 56
- * Familiarizándose con el aparato 59
- 1 Manejo del electrodoméstico 64
- o Home Connect 66
- M Alarma 68
- U Compartimento refrigerador 68
- W Congelador 69
- = Descongelación 71
- D Limpiar 71
- l Olores 72
- 9 Iluminación 72
- > Ruidos 72
- 3 ¿Qué hacer en caso de avería? 73
- 4 Servicio al cliente 75
- ( Indicaciones de seguridad importantes
- Indicaciones de seguridad importantes
- ¡LEER Y CONSERVAR ESTAS INDICACIONES!
- Definiciones
- 9 ADVERTENCIA
- 9 ATENCION
- AVISO:
- Nota:
- Acerca de este manual
- Introducción
- Peligro de explosión
- Riesgo de descarga eléctrica
- Peligro de quemaduras por frío
- Peligro de lesiones
- Riesgo de incendio
- Evitar riesgos para los niños y las personas vulnerables
- Peligro de asfixia
- Daños materiales
- Peso
- Advertencias en virtud de la Proposición 65 del estado de California
- 8 Uso previsto
- 7 Protección del medio ambiente
- 5 Instalación y conexión
- Ahorrar energía
- Si sigue estas instrucciones, el aparato consume menos corriente.
- Nota:
- La disposición de las piezas de equipo no afectará el consumo de energía de aparato.
- Instalar el aparato
- Usar el aparato
- --------
- Antes del primer uso
- 1. Retirar el material informativo y eliminar las cintas adhesivas, así como las láminas protectoras.
- 2. Limpiar el aparato. ~ "Limpiar" en la página 71
- Conexión a la toma de agua
- 9 ATENCION
- Presión del agua de la tubería de agua potable
- 9 ATENCION
- Nota:
- Conexión a la red eléctrica
- 9 ATENCION
- Nota:
- 1. Después de instalar el aparato, esperar al menos 1 hora antes de conectarlo, para evitar daños en el compresor.
- 2. Asegúrese de que la toma de corriente se ha instalado correctamente y cumple con los requerimientos exigidos.
- Requisitos para las tomas de corriente
- Carga simultánea máxima
- 3. Conecte el aparato a una toma de corriente cerca del aparato.
- 9 ADVERTENCIA
- ¡Riesgo de descarga eléctrica!
- 9 ADVERTENCIA
- ¡Riesgo de descarga eléctrica!
- * Familiarizándose con el aparato
- Familiarizándose con el aparato
- Aparato de 2 puertas
- Aparato de 3 puertas
- Controles
- Selección modo de funcionamiento
- Modo Eco
- Modo Vacaciones
- Modo Sabbat
- Ajustes
- Idioma
- Home Connect
- Tonos
- Brillo de la pantalla
- Unidad de temperatura
- Producción de cubitos de hielo
- Contador filtro de agua
- Ajustes de fábrica
- Autocomprobación
- Protección de condens. (solo en aparatos de 3 puertas)
- Modo Demo
- Nota:
- Equipamiento
- Estantes
- 1. Levantar el estante y sacarlo.
- 2. Al colocarlo, inserte los ganchos en la parte posterior del estante a la misma altura, de modo que el estante quede recto.
- Nota:
- Bandeja
- 1. Levantar la bandeja y sacarla.
- 2. Al colocarla, inserte los ganchos en la parte posterior de la bandeja a la misma altura, de modo que la bandeja quede recta.
- Nota:
- recipientes
- Acumulador de frío
- Nota:
- Máquina de hielo
- 9 ATENCION
- ¡Daños en el aparato!
- Notas
- Filtro de agua
- Nota:
- Cambiar el filtro de agua o sustituirlo por un cartucho de filtro con bypass
- Nota:
- 1. Girar la tapa del filtro de agua en el sentido contrario a las manecillas del reloj.
- 2. Sacar el filtro de agua.
- 3. Retirar la tapa del nuevo filtro de agua o del nuevo cartucho de filtro con bypass.
- 4. Retirar la cubierta del filtro de agua usado, y colocarla sobre el nuevo filtro de agua o el nuevo cartucho de filtro con bypass.
- 5. Empujar el nuevo filtro de agua o el nuevo cartucho de filtro con bypass en la apertura del filtro hasta el tope.
- Nota:
- 6. Girar el filtro de agua o el cartucho de filtro con bypass en el sentido de las manecillas del reloj hasta la marca.
- Nota:
- 7. Si se monta un filtro de agua: restablecer el contador de filtro de agua. ~ "Contador filtro de agua" en la página 61
- 8. Desechar los cubitos de hielo que se produzcan en las primeras 24 horas.
- 9. Drenar el agua del filtro de agua usado.
- Nota:
- 1 Manejo del electrodoméstico
- Manejo del electrodoméstico
- Encender el aparato
- 1. Pulse el interruptor principal de encendido/ apagado.
- 2. Ajustar la temperatura deseada. ~ "Ajustar la temperatura" en la página 64
- Advertencias relativas al funcionamiento del aparato
- Apagar y cerrar el aparato
- Apagar el aparato
- Desconectar el aparato
- 9 ATENCION
- 1. Interrumpir el suministro de agua al aparato y esperar durante 3 horas.
- 2. Sacar los alimentos.
- 3. Pulse el interruptor principal de encendido/ apagado.
- 4. Desconectar el enchufe o apagar el fusible.
- 5. Vaciar el depósito de los cubitos de hielo y limpiar el aparato. ~ "Limpiar" en la página 71
- 6. Dejar el aparato abierto.
- Ajustar la temperatura
- Temperatura recomendada
- Ajustar la temperatura del compartimento refrigerador y del congelador
- 1. Seleccionar el compartimento deseado pulsando brevemente el indicador de temperatura.
- 2. Ajustar el indicador de temperatura con el valor deseado.
- 3. Regresar a la pantalla principal con la tecla x.
- Super frío
- Nota:
- Encender o apagar la función súper frío
- 1. Seleccionar el compartimento refrigerador pulsando brevemente el indicador de temperatura.
- 2. Pulsar la tecla ].
- 3. Pulsar Continuar.
- Nota:
- Supercongelación
- Nota:
- Encender o apagar súper congelación
- 1. Seleccionar el congelador pulsando brevemente el indicador de temperatura.
- 2. Pulsar la tecla ].
- 3. Pulsar Continuar.
- Nota:
- Modo Eco
- Modo de vacaciones
- Modo Sabbat
- Encender o apagar la producción de cubitos de hielo
- 9 ATENCION
- Nota:
- Activar o desactivar la protección contra condensación
- 9 ATENCION
- o Home Connect
- Home Connect
- Nota:
- Nota:
- Configurar Home Connect
- Notas
- 1. Instalar la aplicación.
- 2. Conectar el refrigerador a la red doméstica WLAN (Wi-Fi).
- 3. Conectar el refrigerador con la aplicación Home Connect.
- Configuración de la conexión con la red doméstica (WLAN)
- 1. Instalar la aplicación Home Connect en su dispositivo móvil.
- 2. En el aparato refrigerador abrir el menú Home Connect.
- 3. Abrir la aplicación en el dispositivo móvil.
- 4. Iniciar sesión en la aplicación o registrarse si todavía no se ha creado un acceso.
- 5. Comprobar en el router de la red doméstica si existe una función WPS para la conexión automática.
- 6. Si dicha función está disponible, iniciar la conexión automática a la red y seguir las instrucciones del panel de mando.
- 7. Cuando la función mencionada no esté disponible o no esté seguro de ello, o bien cuando haya fallado la conexión automática a la red, iniciar la conexión manual a la red.
- 8. Iniciar la conexión manual a la red en la aplicación del dispositivo móvil.
- Nota:
- Comprobar la intensidad de la señal
- Mejorar la intensidad de señal
- Conectar el aparato refrigerador con la aplicación Home Connect
- 1. Instalar la aplicación Home Connect en el dispositivo móvil y registrarse o iniciar sesión.
- 2. En el aparato refrigerador abrir el menú Home Connect.
- 3. Pulsar la opción de menú Conectar con la aplicación.
- 4. Confirme el mensaje para mostrar el aparato refrigerador en la aplicación.
- 5. Abrir la aplicación y esperar hasta que se muestre el aparato refrigerador. Con Añadir confirmar la conexión entre la aplicación y el aparato refrigerador.
- 6. Seguir las instrucciones de la aplicación hasta que el proceso haya finalizado.
- Instalar la actualización de software de Home Connect
- 1. Abrir el menú Home Connect.
- 2. Pulsar Actualización de software.
- Nota:
- 3. Para instalar la actualización pulsar Instalar ahora.
- Acceso del servicio al cliente
- 1. Contactar al servicio al cliente. ~ "Servicio al cliente" en la página 75
- 2. Confirmar en la aplicación el inicio del acceso de servicio al cliente.
- 3. En cuanto el servicio al cliente haya reunido la información necesaria, se desconectará de su aparato.
- Nota:
- Restablecer los ajustes
- 1. En el aparato refrigerador abrir el menú Home Connect.
- 2. Pulsar la opción de menú Restablecer los ajustes.
- 3. Confirme el mensaje para borrar los ajustes de red.
- Activar o desactivar la conexión con la red doméstica WLAN (Wi-Fi)
- 1. En el aparato refrigerador abrir el menú Home Connect .
- Nota:
- 2. Seleccionar Desconectar Wi-Fi.
- 3. Pulsar Continuar para iniciar la desconexión.
- 4. Tan pronto como se desactiva la conexión con la red doméstica se muestra el mensaje Wi-Fi desconectado. Confirmar el mensaje pulsando Ok.
- Nota:
- Indicaciones sobre protección de datos
- Nota:
- M Alarma
- U Compartimento refrigerador
- W Congelador
- Congelador
- Aprovechar toda la capacidad de congelación del aparato
- Al comprar alimentos congelados
- Al ordenar prestar atención
- Congelar los alimentos frescos
- Alimentos adecuado para congelar
- Alimentos no adecuados para congelar
- Envasado de los productos congelados
- 1. Introducir los alimentos en el envase.
- 2. Eliminar el aire.
- 3. Sellar el envase herméticamente, para que los alimentos no pierdan su sabor o se deshidraten.
- 4. Etiquetar los envases con el contenido y la fecha de congelación.
- Tiempo de conservación de los productos congelados a 0 °F (-18 °C)
- Descongelar los productos congelados
- 9 ATENCION
- = Descongelación
- D Limpiar
- Limpiar
- 9 ATENCION
- Evitar daños al aparato y piezas del equipamiento.
- Limpiar la pantalla
- Limpiar el interior del aparato
- 1. Pulse el interruptor principal de encendido/ apagado.
- 2. Retirar los alimentos y guardarlos en un lugar frío.
- 3. Limpie el aparato con un paño suave, agua templada y un poco de jabón líquido de pH neutro.
- 9 ATENCION
- 4. Limpie la junta de la puerta con agua limpia y séquela bien.
- 5. Vuelva a encender el aparato e introduzca los alimentos.
- Limpiar los accesorios
- Indicación para la conservación de superficies de acero inoxidable
- l Olores
- Olores
- 1. Conectar y desconectar el aparato a través del interruptor principal.
- 2. Retirar todos los alimentos del aparato.
- 3. Limpiar el interior del aparato. ~ "Limpiar" en la página 71
- 4. Limpiar todos los embalajes.
- 5. Envasar herméticamente los alimentos de olor fuerte para evitar la formación de olores.
- 6. Encender el aparato de nuevo.
- 7. Acomodar los alimentos.
- 8. Verificar después de 24 horas si hay olores de nuevo.
- 9. Sustituir el filtro desodorizante. ~ "Sustituir el filtro desodorizante" en la página 72
- Sustituir el filtro desodorizante
- 1. Abrir el soporte del filtro con un destornillador de ranura.
- 2. Retirar el filtro desodorizante agotado y sustituirlo por uno nuevo.
- 3. Cerrar el soporte del filtro.
- 9 Iluminación
- > Ruidos
- 3 ¿Qué hacer en caso de avería?
- Antes de llamar al Servicio al cliente, intente solucionar el problema, utilizando esta tabla.
- Aparato
- Máquina de hielo
- La máquina de hielo no funciona.
- Muy pocos cubitos de hielo o deformados, menos presión de agua de lo habitual.
- Sale agua del aparato.
- --------
- 4 Servicio al cliente
- Servicio al cliente
- Autoprueba del aparato
- 1. Pulsar la tecla Ò para abrir los ajustes.
- 2. Pulsar la opción de menú Autocomprobación.
- 3. Pulsar Iniciar.
- 4. Si existen errores, estos se mostrarán. En ese caso, siga las instrucciones de la pantalla.
- 5. El aparato se reinicia.
- 6. Durante 10 segundos aparece el mensaje de que la autocomprobación se ha completado.
- Solicitud de reparación y asesoramiento en caso de averías
- *8001077621*
- 4 Servicio al cliente
- es Instrucciones de uso
en Instruction manual .............................................................. 2
fr Notice d'utilisation ............................................................ 26
es Instrucciones de uso ........................................................ 51
Fridge-freezer
Réfrigérateur / congélateur combiné
Refrigerador/congelador
B36IT900NP B36BT930NS
B30IB900SP B30BB930SS