User manual

English | 15
Bosch Power Tools 1 609 92A 12F | (9.2.15)
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” complies with all applicable
provisions of the directives 1999/5/EC, 2004/108/EC,
2006/95/EC, 2009/125/EC, Regulation (EC) No.
278/2009, 2011/65/EU including their amendments and is
in conformity with the following standards:
EN 60065:2002-05 + A1:2006-05 + A2:2010-10 +
A11:2008-11 + A12:2011-02,
EN 300 328 V1.8.1:2012-06,
EN 301 489-1 V1.8.1:2008-04,
EN 301 489-1 V1.9.2:2011-09,
EN 301 489-17 V2.2.1:2012-09, EN 62479:2010-09,
EN 55013:2013-06, EN 55020:2007-01 + A11:2011-10,
EN 61000-3-2:2006-04 + A1:2009-07 + A2:2009-07,
EN 61000-3-3:2013-08.
Technical documents at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
12
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 12.01.2015
Assembly
Opening/Closing the Storage Compartment
Fold the rod antenna 23 out of its holder. Then open the lock-
ing latch 4 of the storage compartment and fold open the lid
27.
Note: Close the lid of the storage compartment and lock it
using the latch 4 when operating, transporting or storing the
radio. Otherwise, the radio may become damaged.
Power Supply of Radio
The radio can be powered using the power-supply plug 31 or
using a Li-Ion battery 33.
Operation with Battery Pack (see figures A–B)
Note: The use of batteries unsuitable for your radio can lead
to malfunction or damage to the radio.
Note: The battery pack is supplied partially charged. To en-
sure full capacity of the battery pack, completely charge the
battery pack in the battery charger before using for the first
time.
 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your radio.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
To insert a battery, open the lid 27 of the storage compart-
ment.
– Operation with 10.8 V battery: Insert a 10.8 V battery in-
to the battery port 24 so that the terminals of the battery
rest on the terminals in the battery port 24. Allow the bat-
tery to engage in the battery port.
– Operation with 14.4/18 V battery: Place a 14.4 V bat-
tery or an 18 V battery on the battery receptacle 25 so that
the terminals of the battery rest on the terminals of the bat-
tery receptacle 25. Slide the battery onto the battery re-
ceptacle until it engages.
The battery charge-control indicator b appears on the display
as soon as a battery with sufficient voltage is inserted and the
radio is not connected to the mains by the power-supply
plug 31.
Audio Operation/Radio
Operating voltage
– for operation with power-supply plug
– for battery-pack operation
V
V
12
10.8/14.4/18
Rated output of amplifier (for operation with power-supply plug)
2x3.5W
Reception range
–FM
– AM (3 603 JA9 0.. (EU))
– AM (3 603 JA9 04. (AUS/NZ))
MHz
kHz
kHz
87.5–108
531–1602
522–1611
Portable Radio PRA MultiPower
1) Bluetooth® devices must support the A2DP profile.
2) depending on the battery pack being used
* Limited performance at temperatures <0 °C
Power-supply plug
Article number 1 600 A00 0..
Input voltage
V~ 100–240
Frequency
Hz 50/60
Input current
mA 500
Output voltage
V= 12
Output current
mA 1500
Weight according to
EPTA-Procedure 01/2003
kg 0.2
Protection class
/II
Henk Becker
Executive Vice President
Engineering
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-2386-001.book Page 15 Monday, February 9, 2015 11:37 AM