Robert Bosch GmbH Power Tools Division 70745 Leinfelden-Echterdingen Germany www.bosch-garden.com F 016 L70 545 (2011.
| English. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page F 016 L70 545 | (14.1.
|3 11 1 10 9 2 8 3 7 4 6 5 Aquatak Aquatak Aquatak Aquatak Bosch Power Tools Clic Clic Clic Clic 125 130 135 140 F 016 L70 545 | (14.1.
| A B 1 13 8 7 12 12 C D 13 13 14 13 E F 8 7 F 016 L70 545 | (14.1.
|5 G H 9 10 I 3 J K 15 5 6 L M 16 Bosch Power Tools F 016 L70 545 | (14.1.
| English Safety Notes en Before start-up please read these instructions! Before using the machine please read the operating instructions for your unit and comply in particular with these safety instructions. Please keep the instructions safe for later use. f If an extension cord is used, the plug and socket must be of watertight construction. The extension cord must have a cross section in accordance with the operating instructions and be protected against splashed water.
English | 7 f The appropriate safety regulations must be observed when using the unit in dangerous areas (e.g. petrol stations). It is forbidden to operate the unit in potentially explosive locations. f The unit must be placed on a solid base. f Only use detergents recommended by the manufacturer and comply with the application, disposal and warning instructions of the detergent manufacturers. f All current-conducting components in the working area must be protected against splashed water.
| English Product Description and Specifications Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Intended Use The product is intended for cleaning areas and objects outside the house, tools, vehicles and boats, if the appropriate accessories such as cleaning agents approved by Bosch are used. Intended use is related to operation within 0°C and 40°C ambient temperature.
English | 9 Technical Data Power washer Aquatak Clic 125 Aquatak Clic 130 Aquatak Clic 135 Aquatak Clic 140 3 600 H79 0.. 3 600 H79 1.. 3 600 H79 2.. 3 600 H79 3.. Article number Rated power Supply Temperature max. W 1800 2000 2100 2300 °C 60 60 60 60 Supply rate min. l/min 9 9 9 9 Supply pressure max. MPa* 0 – 0.6 0 – 0.6 0 – 0.6 0 – 0.6 Working pressure MPa* 9 9.5 10 10.5 Max. pressure MPa* 12.5 13 13.5 14 Flow rate l/min 6.8 7.2 7.5 7.
| English Assembly For Your Safety f Warning! Switch off, remove plug from mains before adjusting, cleaning or if cable is cut, damaged or entangled. Aquatak Clic 125/Aquatak Clic 130 Your pressure washer is double insulated for safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Only use approved extension cables. Contact your Bosch Service Centre for details.
English | 11 20 mm 20 mm To store pressure hose 3 or supply cable 6, pull the hose or cable briefly (the hose or cable rolls up automatically). Note: Always pull out the pressure hose and supply cable completely when using the pressure washer. Adjusting 4 Jet-lance (see figure F) The 4 jet-lance has 4 different modes, which can be selected by rotating the nozzle. Give the detergent time to work, but never leave it to dry. Rinse from top and work downwards.
| English Autostop function Self priming function The machine is designed to switch off the motor when the trigger 9 is released on the gun. This feature relieves high pressure from the system to achieve a longer lifetime and lower energy consumption. (A short squeaking noise can occur and is completely normal.) The machine can also operate with water from sources other than a water tap, e. g. ponds and water butts due to the self priming function.
English | 13 Problem Possible Cause Corrective Action Fuses blow Fuses incorrectly rated Change to a mains supply higher than the pressure washer amp consumption Excessive working pressure Nozzle partly blocked Clean nozzle (see figure L) Pressure pulsating Air in the inlet water supply hose/pump Allow pressure washer to run with open spray handle and nozzle at low pressure until regular working pressure is obtained Inadequate water supply Check that the water supply corresponds to specificati
| English Cleaning/inspecting the strainer (see figure M) Expose the strainer 16 in the machine water inlet connection by removing the inlet connector 5. The strainer 16 can be easily removed with long nose pliers. Rinse and replace. If damaged replace. Never use the pressure washer without the strainer or a damaged strainer. After use/Storage Clean the exterior of the machine thoroughly using a soft brush or cloth. Do not use water, solvents or polishes.
English | 15 KZN – BSC Service Centre Unit E, Almar Centre 143 Crompton Street Pinetown Tel.: +27 (031) 7 01 21 20 Fax: +27 (031) 7 01 24 46 E-Mail: bsc.dur@za.bosch.com Western Cape – BSC Service Centre Democracy Way, Prosperity Park Milnerton Tel.: +27 (021) 5 51 25 77 Fax: +27 (021) 5 51 32 23 E-Mail: bsc@zsd.co.za Bosch Headquarters Midrand, Gauteng Tel.: +27 (011) 6 51 96 00 Fax: +27 (011) 6 51 98 80 E-Mail: rbsa-hq.pts@za.bosch.