Cordless hammer drill operating instructions
Table Of Contents
- Titelseite
- GBH 18V-21
- 1 Sicherheitshinweise
- 2 Produkt- und Leistungsbeschreibung
- 3 Montage
- 4 Betrieb
- 5 Wartung und Service
- GBH 18V-21
- 6 Safety instructions
- 7 Product Description and Specifications
- 8 Assembly
- 9 Operation
- 10 Maintenance and Service
- GBH 18V-21
- 11 Consignes de sécurité
- 12 Description des prestations et du produit
- 13 Montage
- 14 Fonctionnement
- 15 Entretien et Service après‑vente
- GBH 18V-21
- 16 Indicaciones de seguridad
- 17 Descripción del producto y servicio
- 18 Montaje
- 19 Funcionamiento
- 20 Mantenimiento y servicio
- GBH 18V-21
- 21 Instruções de segurança
- 22 Descrição do produto e do serviço
- 23 Montagem
- 24 Funcionamento
- 25 Manutenção e assistência técnica
- GBH 18V-21
- 26 Avvertenze di sicurezza
- 27 Descrizione del prodotto e dei servizi forniti
- 28 Montaggio
- 29 Utilizzo
- 30 Manutenzione ed assistenza
- GBH 18V-21
- 31 Veiligheidsaanwijzingen
- 32 Beschrijving van product en werking
- 33 Montage
- 34 Gebruik
- 35 Onderhoud en service
- GBH 18V-21
- 36 Sikkerhedsinstrukser
- 37 Produkt- og ydelsesbeskrivelse
- 38 Montering
- 39 Brug
- 40 Vedligeholdelse og service
- GBH 18V-21
- 41 Säkerhetsanvisningar
- 42 Produkt- och prestandabeskrivning
- 43 Montering
- 44 Drift
- 45 Underhåll och service
- GBH 18V-21
- 46 Sikkerhetsanvisninger
- 47 Produktbeskrivelse og ytelsesspesifikasjoner
- 48 Montering
- 49 Bruk
- 50 Service og vedlikehold
- GBH 18V-21
- 51 Turvallisuusohjeet
- 52 Tuotteen ja ominaisuuksien kuvaus
- 53 Asennus
- 54 Käyttö
- 55 Hoito ja huolto
- GBH 18V-21
- 56 Υποδείξεις ασφαλείας
- 57 Περιγραφή προϊόντος και ισχύος
- 58 Συναρμολόγηση
- 59 Λειτουργία
- 60 Συντήρηση και σέρβις
- GBH 18V-21
- 61 Güvenlik talimatı
- 62 Ürün ve performans açıklaması
- 63 Montaj
- 64 İşletim
- 65 Bakım ve servis
- GBH 18V-21
- 66 Wskazówki bezpieczeństwa
- 67 Opis urządzenia i jego zastosowania
- 68 Montaż
- 69 Praca
- 70 Konserwacja i serwis
- GBH 18V-21
- 71 Bezpečnostní upozornění
- 72 Popis výrobku a výkonu
- 73 Montáž
- 74 Provoz
- 75 Údržba a servis
- GBH 18V-21
- 76 Bezpečnostné upozornenia
- 77 Opis výrobku a výkonu
- 78 Montáž
- 79 Prevádzka
- 80 Údržba a servis
- GBH 18V-21
- 81 Biztonsági tájékoztató
- 82 A termék és a teljesítmény leírása
- 83 Összeszerelés
- 84 Üzemeltetés
- 85 Karbantartás és szerviz
- GBH 18V-21
- 86 Toлько для стран Евразийского экономического союза (Таможенного союза)
- 87 Указания по технике безопасности
- 88 Описание продукта и услуг
- 89 Сборка
- 90 Работа с инструментом
- 91 Техобслуживание и сервис
- GBH 18V-21
- 92 Вказівки з техніки безпеки
- 93 Опис продукту і послуг
- 94 Монтаж
- 95 Робота
- 96 Технічне обслуговування і сервіс
- GBH 18V-21
- 97 Еуразия экономикалық одағына (Кеден одағына) мүше мемлекеттер аумағында қолданылады
- 98 Қауіпсіздік нұсқаулары
- 99 Өнім және қуат сипаттамасы
- 100 Жинау
- 101 Пайдалану
- 102 Техникалық күтім және қызмет
- GBH 18V-21
- 103 Instrucţiuni de siguranţă
- 104 Descrierea produsului şi a performanțelor sale
- 105 Montarea
- 106 Funcţionarea
- 107 Întreţinere şi service
- GBH 18V-21
- 108 Указания за сигурност
- 109 Описание на продукта и дейността
- 110 Монтиране
- 111 Работа с електроинструмента
- 112 Поддържане и сервиз
- GBH 18V-21
- 113 Безбедносни напомени
- 114 Опис на производот и перформансите
- 115 Монтажа
- 116 Употреба
- 117 Одржување и сервис
- GBH 18V-21
- 118 Bezbednosne napomene
- 119 Opis proizvoda i primene
- 120 Montaža
- 121 Režim rada
- 122 Održavanje i servis
- GBH 18V-21
- 123 Varnostna opozorila
- 124 Opis izdelka in storitev
- 125 Namestitev
- 126 Delovanje
- 127 Vzdrževanje in servisiranje
- GBH 18V-21
- 128 Sigurnosne napomene
- 129 Opis proizvoda i radova
- 130 Montaža
- 131 Rad
- 132 Održavanje i servisiranje
- GBH 18V-21
- 133 Ohutusnõuded
- 134 Toote kirjeldus ja kasutusjuhend
- 135 Paigaldamine
- 136 Töötamine
- 137 Hooldus ja korrashoid
- GBH 18V-21
- 138 Drošības noteikumi
- 139 Izstrādājuma un tā funkciju apraksts
- 140 Montāža
- 141 Lietošana
- 142 Apkalpošana un apkope
- GBH 18V-21
- 143 Saugos nuorodos
- 144 Gaminio ir savybių aprašas
- 145 Montavimas
- 146 Naudojimas
- 147 Priežiūra ir servisas
- GBH 18V-21
- GBH 18V-21
- GBH 18V-21
- 158 دستورات ایمنی
- 159 توضیحات محصول و کارکرد
- 160 نصب
- 161 کار با دستگاه
- 162 مراقبت و سرویس
16 | English
– To switch on the power tool, press the on/off switch(9).
The worklight (12) lights up when the on/off switch (9) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
– To switch off the power tool, release the on/off switch
(9).
For low temperatures, the power tool reaches the full ham-
mer/impact capacity only after a certain time.
Adjusting the Speed/Impact Rate
– Adjust the speed/impact rate of the power tool when it is
on by pressing in the on/off switch(9) to varying extents.
Applying light pressure to the on/off switch(9) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Overload clutch
u If the application tool jams or snags, the power trans-
mission to the drill spindle will be interrupted. Always
hold the power tool firmly with both hands to with-
stand the forces this may create and adopt a position
with stable footing.
u Switch the power tool off immediately and remove the
application tool if the power tool becomes blocked.
Switching on when the drilling tool is blocked may
cause high torque reactions.
Practical Advice
Setting the drilling depth (see figure D)
You can use the depth stop (15) to set the required drilling
depthX.
– Press the button for depth stop adjustment (5) and insert
the depth stop into the auxiliary handle (14).
The fluting on the depth stop (15) must face downwards.
– Insert the SDS-plus application tool into the SDS-plus tool
holder (2) to the stop. Otherwise, the movability of the
SDS-plus drilling tool can lead to incorrect adjustment of
the drilling depth.
– Pull the depth stop far enough out that the distance
between the drill bit tip and the edge of the depth stop
corresponds to the required drilling depth X.
Changing the chiselling position (Vario-Lock)
You can lock the chisel in 13 different positions, so you can
select the optimum working position for each task.
– Insert the chisel into the tool holder.
– Turn the impact/mode selector switch (7) to the "Vario-
Lock" position.
– Turn the application tool to the required chisel position.
– Turn the impact/mode selector switch (7) to the "chis-
elling" position. With this, the tool holder is locked.
– Set the rotational direction for chiselling to clockwise.
Inserting screwdriver bits (seefigureE)
u Only apply the power tool to the screw/nut when the
tool is switched off. Rotating tool inserts can slip off.
A universal holder (16) with SDS-plus shank (accessory) is
required to work with screwdriver bits.
– Clean and lightly grease the insertion end of the shank.
– Insert the universal holder into the tool holder while turn-
ing it until it locks automatically.
– Check that it is locked by pulling the universal holder.
– Insert a screwdriver bit in the universal holder. Only use
screwdriver bits that fit the screw head.
– To remove the universal holder, slide the locking sleeve
(4) backwards and remove the universal holder (16)
from the tool holder.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Only store the battery within a temperature range of −20 to
50°C. Do not leave the battery in your car in the summer, for
example.
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.
Maintenance and Service
Maintenance and Cleaning
u Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
u To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
u Replace a damaged dust protection cap immediately.
It is recommended that you have use an after-sales
service for this.
– Clean the tool holder(2) after each use.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
1 609 92A 5GG | (13.01.2020) Bosch Power Tools