User's Manual

Bosch Security Systems, Inc. | 2
Callout ― Description
1 ― Flat surface mounting holes
2 ― Corner surface mounting holes
3 ― Horizontal removable bubble level
4 ― Vertical position bubble level holder
(swivel mount only)
5 ―
Tamper plate
6 ― Rotary lock
7 ― Battery tray location
8 ― Feature switches
9 ― Look-down adjustment
10 ― Tamper switch
1
3
4
5
6
1
2
8
9
7
10
1
2
2
2
1 | Overview
3 | Installation considerations
4 | Installation
Figure 1.1: Detector base interior view
(top), detector body interior view (bottom)
The RADION TriTech ZB is a wireless PIR and
Doppler radar motion detector with ZigBee
technology that is simple to install.
Point away from:
– Glass exposed to the outdoors
– Direct and indirect sunlight
– Objects that change temperature
rapidly such as heat sources or air
conditioning outlets
– Outside traffi c
– Objects animals might climb on
(stairs, shelves, furniture)
Install:
– On solid, vibration free surface
– On a fl at or corner surface
– Within recommended mounting height
range measured from the fl oor
– Where an intruder is most likely to
cross through the coverage pattern
Do not install:
– Near rotating machines or other
moving objects within the coverage
pattern
– Near objects that can block the fi eld-
of-view
– Where an intruder would only walk
directly toward or away from the
detector.
– Near direct hot or cold drafts
Pet immunity:
– Up to 100 lbs (45 kg)
Open the detector and mount the base to
either a fl at surface, a corner, or a bracket.
Opening the detector:
1. Turn the rotary lock at the bottom of the
detector to the open position. The body
slides down. Refer to Figure 4.1.
2. Pull apart to remove it from the base.
Figure 4.1: Unlock and open detector
Mounting the base:
1. Identify mounting location and surface
for install. (Optional mounting brackets:
B335 and B338. Sold separately).
2. Identify mounting holes to use based on
the mounting surface. Refer to Figure 1.1.
3. Break away or drill through the
appropriate mounting hole coverings in
the base.
1
NOTICE!
Do not break away or separate the
tamper plate from the base.
Figure 4.2 Surface mount: left; corner
mount: right
Leveling the motion detector:
1. Position the base on the surface and
mount in place using one screw and
drywall anchor only. Do not over-tighten.
Figure 4.3: Level detector
5 | Confi guration
Setting the switches:
1. Switch 1- Radar sensitivity. This detector
has two sensitivity settings; HI and LO.
The default is set at HI. This setting
provides optimal detection for most
installations. Set the sensitivity to LO to
decrease the radar range. Refer to table
5.1.
2. Switch 2 - LED illumination. The LED
illuminates when the device detects PIR
and Doppler radar activity. By default,
the LED is off (switch down). Place the
switch in the on position (switch up) if
you want the LED illumination during
normal operation.
Confi gure the features and options located on
the detector body before placing the detector
body on the base.
5.1 | Set the switches
2
NOTICE!
Use of a bracket might reduce
range and increase dead zone
areas.
NOTICE!
At least one screw must be
inserted into the tamper plate
for tamper protection.
A. B.
NOTICE!
Supported mounting heights range
from 7.5 ft to 9 ft (2.3 m to 2.7 m).
2. Use the bubble level to ensure the base
is level from side to side. Refer to Figure
4.3 - A.
3. Remove the bubble level and place it
into the bubble level holder to verify
vertical alignment. This is applicable
for swivel mount brackets only. Refer to
Figure 4.3 - B.
4. Make adjustments until the base is
level, and mark the remaining surface
mounting hole locations.
5. Remove the bubble level from the
holder and place it back to its original
position.
6. Secure the base with the remaining
screws. Use a total of 3 screws and
drywall anchors for surface mount
installations, and 2 screws and drywall
anchors for corner mount installations.
2 | Product Contents
This poduct contains:
– Wireless motion detector
– Installation instructions
– Hardware pack
– Battery tray with one battery
You will need a power drill with a phillips
head bit and a fl at-head screwdriver to
perform the installation.
Use a smart phone and scan the following
QR code for more information regarding
installation and mounting considerations.
PRELIMINARY