UR-220S / 220D Series Professional UHF Wireless Microphones Installation and Operation
Contents Introduction… … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … …P3 Receiver Installation and Connections… … … … … … … … … … … … … … … … … … … … … …P4 ·Installation… … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … …P4 ·Connections… … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … …P4 Receiver Controls and Functions… … … … … … … … … … … … … … … … … … … … … … … …P5 UR-220S Front panel… … … … … … … … … … … … … … … … … … … … … … … … … … … … … …P5 UR-220S Rear panel… …
Introduction ①EIA-standard metal 1/2 - rack receiver chassis, antenna diversity. ②The Handheld Transmitter offers durable, ergonomic metal bodies, soft-touch controls. ③Bright and easy-to-read LCD display shows RF/AF, diversity strengths; transmitter battery level; meanwhile, can set up selective channel, frequency, mute and other working status.
Receiver Controls and Functions Figure A: UR-220S Receiver Front Panel Figure B: UR-220S Receiver Rear Panel ①Power Switch：Press power switch in 3 seconds and the receiver readouts will light. ②Infrared Data Transfer Button (SYNC): Press this button to transmit the channel data from receiver to transmitter. ③Infrared Data Transfer Window (iR): Transmit channel data from the receiver to the transmitter, so that they are in the same frequency.
Figure C: UR-220D Receiver Front Panel ①Power Switch：Press power switch in 3 seconds and the receiver readouts will light. ②A Channel LCD Window: Liquid Crystal Display indicates control setting and operational readings. See “System setup” on page X for details. ③Infrared Data Transfer Window (iR): For both A and B channel. Transmit channel data from the receiver to the transmitter, so that they are in the same frequency.
Transmitter Controls and Functions Handheld Microphone Figure D: UR-220D Receiver Rear Panel 1 2 3 4 5 6 7 8 9 10 ①AC Power Input: IEC type connector for 100-240V, 50/60Hz without user adjustment. ②Antenna Input Jack: BNC type antenna connector for tuner ”B”, attached the antenna directly. ③B Channel Volume Button: To adjust the volume. ④A Channel Volume Button: To adjust the volume. ⑤B Channel Balanced Output Jack: XLR type connector.
Transmitter Battery Installation: Body-pack Transmitter 1 3 4 7 1 2 5 6 8 9 ①Antenna ②Power Button ③Mute Button: When the transmitter is muted, it products RF with no audio signal modulation; when the transmitter is un-muted, it products both RF and audio. ④Audio Input Jack: To connect 4-pin mini-XLR connector. ⑤LCD Window: Liquid crystal display indicates operational frequency, channel and battery condition. The transmitter's “fuel gauge” battery indicator displays a maximum of 4 bar segments.
System Setup Receiver Setup ①Turn down the AF level of the associated mixer or amplifier, and make sure that any UR transmitters are turned off. ②Turn on the receiver, the LCD displays the preset data. ③To change the frequency by manual or “AFS” (Auto Frequency Scan). a, Touch / button once to select a new frequency. b, Press and hold / button 3 seconds and the receiver will auto-scan and lock on to an open, interference-free frequency.
A, Turn on one transmitter, to let the transmitter IR receiving window face to the receiver IR data transfer window, then press A Channel's “SYNC” button, the transmitter will receive the frequency / channel dada from A Channel, simultaneously the LCD displays the same frequency / channel as the receive A Channel. Transmitter Setup ①Press and hold power button 3 seconds, the LCD window comes on.
07 Specifications UR-220S / UR-220D Receiver Main Frame Size: EIA STANDARD 1/2 U (UR-220S) / EIA STANDARD 1U (UR-220D) Channels: Single Channel (UR-220S) / Dual Channel (UR-220D) Frequency Stability: ±0.
USA acceptable band ( FCC compliance ): 618.500 MHz – 633.500 MHz Canada acceptable band ( IC compliance ): 678.500 MHz – 693.500 MHz Europe acceptable band ( CE compliance): 850.000 MHz – 865.000 MHz FCC NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
