User Manual

English | 13
Bosch Power Tools 1 609 92A 2DH | (1.8.16)
Technical Data
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-1.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745-2-1.
Drilling into metal: a
h
<2.5m/s
2
, K =1.5 m/s
2
Screwdriving without impact: a
h
<2.5m/s
2
, K =1.5 m/s
2
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Battery Charging (see figure A)
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
To remove the battery 10 press the unlocking buttons 9 and
pull out the battery downwards. Do not exert any force.
Observe the notes for disposal.
Changing the Tool (see figure B)
 Before any work on the power tool, remove the battery.
Inserting
Pull the locking sleeve 1 toward the front and then push the in-
sert tool to the stop into the tool holder 2. The insert tool is au-
tomatically locked.
Removing
Pull the locking sleeve 1 forward and remove the insert tool.
Dust/Chip Extraction
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Prevent dust accumulation at the workplace. Dust can
easily ignite.
Operation
Starting Operation
Inserting the battery
Note: Use of batteries not suitable for the machine can lead to
malfunctions of or cause damage to the power tool.
Cordless angle drill/driver GWI 12V-5
Article number
3 601 C60 U..
Rated voltage
V= 12
No-load speed
min
-1
0–585
Max. torque for hard/soft screwdriv ing
application according to ISO 5393
Nm 13/5
Torque adjustment range
Nm 2.6 – 5.2
Max. screw dia.
mm 5
Max. drilling dia.
– Steel
– Wood
mm
mm
8
10
Weight according to
EPTA-Procedure 01:2014
kg 1.1 – 1.4*
Permitted ambient temperature
– during charging
– during operation** and during
storage
°C
°C
0... +45
-20... +50
Recommended batteries
GBA 12V..
GBA 10,8V..
Recommended chargers
GAL 12.. CV
AL 11..CV
* depending on the battery pack being used
** limited performance at temperatures <0 °C
OBJ_BUCH-2917-001.book Page 13 Monday, August 1, 2016 11:41 AM