User Manual

en
|
42
|
User guide
| HDS 200/HDS 250
HD Scan Tool for Class 4-8 Diesel, Light and Medium Vehicles
581618 | REV. B | 11.2018
Bosch Automotive Service Solutions Inc.
• Disconnect and reconnect DLC making sure it is
connected correctly.
• Check vehicle battery to make sure at least 8.0 volts
is present.
• Contact customer service.
• With the engine off, check for blown fuses in the
vehicle fuse box.
7.3 Vehicle Communication Fault
The vehicle’s control module(s) enters into an unrecov-
erable state.
1. Turn vehicle key to off position.
• Wait 10 seconds.
• Press .
Vehicle Required
Press ENTER to continue
Please verify the tool is
connected to the vehicle with
the ignition key turned on.
7.4 Operating Error or Erroneous Data
An Operating Error or Erroneous Data occurs if vehicle’s
computer(s) stop(s) communicating with the scan tool.
1. Make selection.
• Use the LEFT and RIGHT keys.
• Press .
Check connection! Try
again?
LINK ERROR
No
Yes
7.5 Battery Replacement
The scan tool requires 4-AAA alkaline batteries to oper-
ate without vehicle power.
• When the batteries need to be replaced, the low-
battery icon ( ) is displayed.
• Rechargeable batteries do not last as long as alka-
line types and are not recommended.
• Non-rechargeable Lithium (Li) battery can be used.
Lithium types last longer than the alkaline types, but
they are more expensive.
1. Place display face-down on a non-abrasive surface.
2. Remove battery cover by turning phillips screw
counterclockwise. Slide battery cover off.
3. Remove batteries and properly discard.
4. Install four new AAA Alkaline batteries.
5. Reinstall battery cover by sliding battery cover on.
Install phillips screw turning it clockwise. Do not
overtighten screw.
7.6 Tool Self-Tests
Tool Self-Tests check the display, keys, and internal
memory.
• Refer to “4 Using the Scan Tool” on page 10 for
the operation procedures for scan tool self-tests.
7.7 Technical Support
Toll-Free Number: 1-855-267-2483.
8 Appendix A—Global OBD II
PID Definitions
Although there are in excess of 300 PIDs, the tool only
displays the PIDs the vehicle supports.
PID PID Description
ABS FRP Absolute Fuel Rail Pressure
ABS LOAD Absolute Load Value
ABS TPS B, C Throttle Position B, C
ABSLT TPS Absolute Throttle Position
ACC POS D Accelerator Pedal D, E, F
ACC POS REL Relative Accelerator Pedal Position
AECD1_TIME1,
TIME 2
Total Run Time with EI-AECD #1 Timer
1 Active, #2 Timer Active
AECD10_TIME1,
TIME 2
Total Run Time with EI-AECD #10
Timer 1 Active, #2 Timer Active
AECD11_TIME1,
TIME 2
Total Run Time with EI-AECD #11
Timer 1 active, #2 Timer Active
AECD12_TIME1,
TIME 2
Total Run Time with EI-AECD #12
Timer 1 active, #2 Timer Active
AECD13_TIME1,
TIME 2
Total Run Time with EI-AECD #13
Timer 1 active, #2 Timer Active
AECD14_TIME1,
TIME 2
Total Run Time with EI-AECD #14
Timer 1 active, #2 Timer Active
AECD15_TIME1,
TIME 2
Total Run Time with EI-AECD #15
Timer 1 active, #2 Timer Active
AECD16_TIME1,
TIME 2
Total Run Time with EI-AECD #16
Timer 1 active, #2 Timer Active
AECD17_TIME1,
TIME 2
Total Run Time with EI-AECD #17
Timer 1 active, #2 Timer Active