SYMBOLS WARNING ICONS Your power tool and its Owner's Manual may contain “WARNING ICONS" (a pleasure symbol intended to alert you to, and/or Instruct you how to avoid, a potentially hazardous condition). Understanding and heading these symbols will help you operate your tool better and safer. Shown below are some of the symbols You may see. SAFETY ALERT: Precautions that involve your safely.
SB eee] cE GENERAL SAFETY INSTRUCTIONS BEFORE USING THIS POWER TOOL Satiety ls a combination of conman sense; staying ser and knowing how to tse your power fol CAUTION To avoid mistakes that could cause serious injury, do not plug the tool in until vou have read and understood the following.
BOWER TOOL SAFETY Alignment of moving pails, binding of moving pars, breakage of pars mounting and any other conditions that may affect is operation: Guard or other pan thatch damaged should be proper repaired or replaced. CLEVER LEAVE THE TOLD RUNNING UNATTENDED. TURN THE POWER "OFF". Dio not walk away from a running tole nail the blade tomes 10a complete stop and the took is unplugged fom the power Source, CROUTON OVERREACH.
UNBOUND MITER SAW SAFETY SPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW 1: DO NOT operate tho miler saw unlit iris completely assembled and installed according 10: these convictions: LE YOU ARE NOT thoroughly tatamis with the operation of miter saws, seek guidance from your supervisor instructor or other qualified parson.
ELECTRICAL REQUIREMENTS AND SAFETY ELECTRICAL REQUIREMENTS — cont'd DOUBLE INSULATED The power tool js double insulated 10 provide & double thickness of insulation between you and fouls elegiacal system All Exposed metal pans arg gladiola from the internal metal rooter components: with protecting insulation.
Eaton ACCESSORIES AND ATTACHMENTS RECOMMENDED ACCESSORIES CAUTION & Use only accessories recommended for this miter saw. Follow instructions that so company accessories. Use of improper accessories may cause hazards. The use of any cutting tool except 12:0 saw blades which meet the requirements under recommended accessories is prohibited.
CARTON CONTENTS UNPACKING YOUR MITER SAW CAUTION To avoid injury from unexpected starting or electrical shock, do not plug the power cord inch a source of power during unpacking and assembly. This cord must remain unplugged whenever you are working on the saw 1 Remove the miller saw Prom the carton. IMPORTANT: Do not lit miler saw by the trigger switch handle: lk may cause misalignment. Lift machine by the builtin carry handle. 2: Place the saw ona secure stationary work surface.
KNOWN OUR SLIDING MITER SAW Upper blade guard Carry handle Switch handle JOGGING trigger switch Sel Eight extension wing.
GLOSSARY OF TERNS AMPERAGE (AMPS A measure phi be flown] fleeciness comet Higher ratings generally means he tool is lusted for heavier use. ARBOR LOG © allows the Serine keep the blade controlling while Tightening of loosening the arbor helot during blade replacement or removal BASE = Supposition (able holds accessories and allows for workbench of lag set mounting.
Seems aE BT ESTIMATED ASSEMBLY TIME: 10:15 MINUTES CAUTION To avoid injury; do not connect this miter saw other power source until iris completely assembled and adjusted; and you have read and understood this Operator's Manual. UNLOCKING THE SLIDE CARRIAGE (FIG.
INSTALLING THE SAFETY HOLD-DOWN g Lave {El 5) + Page the hold-down clamp assembly (11 in une nl the mounting holes (2). Thread the hold-down clamp knobs (3) into {he holes located at the rear of the saw base. © Tighten the hold-down clamp knobs (3) 5 fig. 5 POWER CORD STORAGE CLIPS (FIG. 8) Inconvenience and to prevent damages tithe power cord when the miter saw iB snootiness ors in transportation, the slide carnage has wo clips on the rear for cord storage.
MOUNTING THE MITER SAW (FIG. 8,10) CAUTION To avoid injury form unexpected saw movement: Disconnect the power cord from the outlet, and lock the switch head in the lower position Using the stop latch. Lock the slide carriage in place by tightening the slide carriage Jock knob: To avoid back injury, ft the saw by using ihe designated carrying handles located on the top of the machine.
holding the lower blade guard, lighten the screw with Philips screwdriver: (Fig 11) NOTE: The lower blade guard mist ba raised oie Upright position to Bonces the cover pints screw. Lower the clear retractable blade guard (1) advent ibe operation of the guard does not bind or stick (Fig £1 7. Be sure the arbor look is released so the blade turns freshly by spinning the blade until tha arbor look disengages. CAUTION 8.