D9000/D7000 Series Control/Communicator Operation and Installation Manual 74-07692-000-C 4/97
Text marked with a diamond (♦) indicates that this function or feature is available on the D9412 and D7412 only. Preface This manual addresses the operation and installation of the D9412, D9112, D7412, and D7212 Control/Communicators only, and should not be used in conjunction with the D9112B1 or D7212B1 panels. The table below provides an overview of the differences between the D9000/D7000 Series Control/Communicators.
FCC Notices Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Table of Contents 2 3 3 3 Battery Discharge/Recharge Schedule ........ 16 Charging Status and Low Battery LEDs ........... 17 Charging Status LED (Yellow) ..................... 17 Low Battery LED (Red) ................................ 17 Introduction ........................................................... 7 Points ............................................................... 7 Areas and Accounts ......................................... 7 Communicator ................................................
Wiring Data Expansion Loops to POPEX Modules ......................................... 29 POPIT Sensor Loops .................................. 29 POPIT Module Point Assignments .............. 29 D8128C OctoPOPIT Module ............................ 30 Description .................................................. 30 Listing ......................................................... 30 Installing the OctoPOPIT ............................ 30 Wiring OctoPOPITs .....................................
Figures and Tables Figure 1: System Configuration .................................................................. 7 Figure 2: Enclosure Mounting ................................................................... 11 Figure 3: Reset Pin ..................................................................................... 12 Figure 4: Charging and Battery LEDs ........................................................ 17 Figure 5: Connecting D8132 Modules ....................................................
Introduction ♦ D 9210 B m odu les m ay be use d fo r ac cess con trol. (D 9 412 /D 74 12 only) D 8 1 2 5 In te rfa ce fo r D 8 1 2 7 /D 9 1 2 7 P O P IT S P o in ts 9 - 1 2 7 D 8 1 28 C O ctoP O P IT co m b in es 8 P O P IT P oin ts in o ne m o d u le. D 8 1 29 Oc to R e la y p ro vi de s a la rm a n d a u xil iary re la y o u tp u t. (O th er fun c tio n s a v aila b le .
♦ Communicator The Control/Communicator uses a built-in digital communicator to send reports to the receiver. The panel transmits reports in either the Modem IIIa2 TM or BFSK format. Your D6500 receiver's MPU and line cards must have software revision 8.00 (or greater) installed to accept Modem IIIa2 TM reports from the panel. Power your receiver down and up to print the software revision numbers. The panel connects to an RJ31X jack for phone line seizure.
EMI/Lightning Transient Protection The D9000/D7000 Series Control/ Communicators maintain the Radionics high level of quality and field dependability. Their design significantly reduces electromagnetic interference and malfunction generally caused by lightning.
Listings and Approvals The D9000/D7000 Literature Pack includes the D9000/D7000 Series Approved Applications Compliance Guide (74-07693-000). Refer to this guide for additional guidelines for installing the Control/Communicator in UL and Fire specific applications. Fire UL Underwriters Laboratories lists the D9412, D9112, D7412, and D7212 Control/Communicators as Signal System Control Unit for: Central Station, Local, Auxiliary, Remote Station, and Household Fire Warning.
Installation Before You Begin Beginning the Installation This Installation section contains a general installation procedure. It refers you to other sections of the manual for detailed instructions. Radionics recommends you review this manual and the D9000/D7000 Series Program Entry Guide (74-07695-000) before you begin the installation to determine the hardware and wiring requirements for the features you want to use. Mounting the Enclosure Mount the enclosure in the desired location.
Installing the Assembly 1. 2. 3. Place the assembly over the inside back of the enclosure, aligning the large rectangular openings of the mounting skirt with the mounting hooks of the enclosure. Slide the assembly down so it hangs on the hooks. See Figure 2. Remove the tape from the #6x1/4" screw in the mounting tab on the assembly. The screw passes through the mounting tab and into the skirt mounting hole in the enclosure. Tighten the screw to secure the assembly in the enclosure.
Instructions for wiring the off-board point POPIT sensor loops are found in the instructions packaged with the POPIT modules. Install Modules and Relays 1. 2. Power Down First: Power down the unit by unplugging the transformer and disconnecting the battery. Radionics recommends that you power down the unit when installing modules or relays, or when making wiring connections to the panel. Install and wire any modules required for your installation as described in the module’s installation instructions.
Testing the System After finishing the installation and programming of the panel, make a complete functional test of the system. Test the panel and all devices for proper operation. Test after you first program the panel and after any subsequent programming session. Service Walk Test shows extra points: Use the service walk test at a panel wide Command Center to perform a complete test of the panel.
Power Supply Primary Power Terminals 1 2 Primary (AC) Power Circuit A 16.5 VAC, 40 VA internally fused transformer (Radionics model D1640) is the primary power source. The AC power circuit provides 1.9 Amps of rectified AC power. The panel reserves 500 mA of this power for internal operations leaving 1.4 Amps for powered devices. Transient suppressors and spark gaps protect the circuit from power surges. This protection relies on the ground connection at terminal 10.
D8132 boosts battery backup: Adding a D8132 Battery Charger Module supports additional batteries of up to 36 Ah capacity if required. Failure to add a D8132 will cause situations that create false alarms and differential voltage levels. You can use the D8132 Battery Charger Module to connect two additional batteries for a total of four. The panel plus any connected D8132 modules and AUX power supplies must be on the same AC circuit so they will discharge evenly if AC power fails.
Charging Status and Low Battery LEDs • Yellow LED flashing once per minute The yellow LED normally flashes once per minute as the system checks the battery. • Yellow and red LEDs flashing once per minute The yellow and red LEDs flash on once every minute when current draw for devices connected to the power outputs exceeds 1.4 Amps and the battery is missing. Charging Status LED (Yellow) The yellow LED shows the charging status of the battery. Figure 4 shows its location.
Power Outputs Circuit Protection Three self-resetting thermal circuit breakers protect the panel from short circuits on both the continuous and programmable power outputs. The circuit breakers are thermal rated and open at 3 to 5 Amps. If the panel is programmed for power supervision and short is sustained on one of the power outputs, the panel transmits a BATTERY LOW or BATTERY MISSING for Radionics’ Modem IIIa2 ™ Communication Format, or TROUBLE ZN 9 for BFSK.
17-05823-002 LEDs Off When Normal YE L Operation Monitor Pulses When Normal Flickers When Ringing Charging Status Reset Pin Disable All Except Battery Charging And Programming 1 .4 Am ps 1 2 D 8132 1.4 Am ps (+ ) (-) GR N Low Battery RED + AUX POWER 4 BATTERY NEGATIVE O NLY M ax imum Charging C urrent 1.4 Am ps. 5 BATTERY POSITIVE ON LY 6 STEADY O R + PULSE 7 + ALTER NATE + SW ITC HED AU X POW ER 4 D 8132 (+ ) 8 8 1 .
Relay Installation Power down the system before inserting the D136 relays. The plug-in relays are shorter than the sockets they plug into. See Figure 6. You can install them in either the left or right end of the socket. Don’t rely on relay labelling: You shouldn’t rely on the labelling to install D136 relays. Check for the side with three pins. The three pins go on the top side. Incorrect insertion does not damage the relay or the system, however the related circuits do not function properly.
Telephone Connections Registration Phone Cord Connection The Radionics D9412, D9112, D7412, and D7212 Control/Communicator panels are registered with the Federal Communication Commission under part 68, for connection to the public telephone system using an RJ31X or RJ38X jack installed by your local phone company. Notification Do not connect registered equipment to party lines or coin-operated telephones.
The panel stops monitoring the phone line during its phone line trouble response. If the response includes sending a report, the panel does not resume monitoring until the report is acknowledged or it goes into communication failure. Bad line may test OK: The telephone line monitor uses voltage and current levels to test the status of the phone line. In some instances a given telephone line may be out of service without affecting the voltage on the line.
Set the ring count above 2 on answering machines: The line's RAM Monitor feature may not operate correctly if you connect an answering machine with a ring count of less than 2 rings, to a phone line used by the D928 module. Operation The panel always uses the primary phone line to initiate phone calls, unless it has been detected as faulted. See Phone Line Monitor in this manual for a description of the panel’s phone line monitor operation.
D928 Status LEDs Four LEDs mounted on the front edge of the D928 module show the status of AC power for the panel, the status of the two phone lines, and communication failure. See Figure 10. When programmed and operating normally, only the green AC power status LED should be lit. AC Power LED The green AC power status LED lights when there is AC power at terminals 1 and 2 on the panel.
On-Board Points Point Parameters Description Terminals 11 to 22 The panel provides eight on-board points. Each point functions independently and does not interfere with the operation of the others. The panel monitors the sensor loops for normal, shorted, or open conditions between an input terminal (11, 13, 14, 16, 17, 19, 20, or 22) and any of the point common terminals (12, 15, 18, and 21). Programming for the point determines how the panel responds to those conditions.
Off-Board Points Point (ZONEX) Bus D9412/D9112 Terminals 23 to 28 D7412/D7212 Terminals 27 to 28 On the D9412/D9112, you can use POPIT (Point of Protection Input Transponder) modules to provide up to 238 off-board points, bringing the total number of points the D9412/D9112 can monitor to 246. The D7412/D7212 can provide up to 67 off-board points bringing the total number of points the D7412/D7212 can monitor to 75. Each off-board point requires a POPIT module.
Figure 12: Connecting the D8125 POPEX to the Panel Point 5 17 4 16 18 19 Po int 6 D9000/D7000 Series Operation & Installation Manual Page 27 21 22 Point 8 GRN N.F.P.A. Style 3.
Installing the D8125 POPEX Module Save the POPIT Label Sheets: The D8125 is packaged with two sets of POPIT label sheets. One is marked for use with the D9412/D9112. Save this set. You will use it later to label the POPITs. Mounting Follow the procedure below to install the D8125 in the enclosure with the panel. 1. 2. Align the D8125 POPEX module with any of the four mounting locations in the enclosure. See Figure 2.
Wiring Data Expansion Loops to POPEX Modules There are two positive (+) and two negative (-) data expansion loop terminals on each POPEX module. Follow the procedure below to connect the data expansion loops to the D8125 POPEX Module. See Figure 12. Remember, you can only connect a maximum of 119 POPITs to one D8125 on the D9412/D9112 and 67 for the D7412/ D7212. 1. 2.
POPIT Labels Off-board points for the D9412 and D9112 are numbered 9 to 127 and 129 to 247 (D7412 and D7212 use points 9-75 only). The D9412/D9112 reserves points 128 and 248 for internal use. You must connect POPITs for points 129 to 247 to expansion loops connected to POPEX #2. Two sheets of peel-off POPIT labels are supplied with the D8125 POPEX module. Use the sheet marked Bank1 for points 9 to 127. Use the sheet marked Bank2 for points 129 to 247. Each label has two parts.
Wiring OctoPOPITs OctoPOPIT Sensor Loops Follow the procedure below to wire D8128C OctoPOPIT Modules to the D9412/D9112. You can connect OctoPOPIT and POPEX modules to the same Point Bus terminals. The modules wire in parallel. Remember you can never assign the same point number to more than one point. 1. Power down first: Power down the panel by disconnecting the positive (red) battery lead at the battery and unplugging the transformer. 2.
ZO N EX B US 1 Sw itch "0" O N (P o in ts 9 - 7 2 ) Z O N EX B US 1 Sw itch "0" O FF (P o in ts 7 3 - 1 2 0) 0 1 2 3 4 0 1 2 3 4 O N O N F irst A dd res s on Z O N E X B us 1 3 4 5 P1 6 COM 8 9 COM 7 9 COM P2 P3 8 7 P2 P3 COM P6 P7 P 6 P7 COM COM P8 P8 10 11 12 13 14 15 16 P4 P 5 COM 10 11 12 13 14 15 16 P4 P5 SENSOR L OOPS OUT AUX 6 COM 25 2 5 P1 26 IN 4 SE NS OR LO OP S 1 3 27 OUT AUX 28 TO CO NT RO L 2 IN Co ntrol/Co mm unicator Pa ne l Bu s 1 con tinue
D8128C Sensor Loop P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 P1 P2 P3 P4 P5 P6 P7 P8 ZONEX 1 D9412 Point D8128C Switches 0 1 2 ZONEX 2 3 009 010 011 012 On On On On 013 014 015 016 017 018 019 020 On On On Off 021 022 023 024 025 026 027 028 On On Off On 029 030 031 032 033 034 035 036 On On Off Off 037 038 039 040 041 042 043 044 On Off On On 045 046 047 048 049 050 051 052 On
Off-Board Relays D8129 OctoRelay The D8129 OctoRelay allows you to add relay outputs to your system in groups of eight. On the D9412/D9112, up to 128 OctoRelay outputs (relay numbers 1 to 128) can be added to your system using 16 OctoRelays. The D7412/D7212 allows up to 64 relay outputs. Review the Power Outputs section of this manual to be sure you provide enough power for the OctoRelays and other powered devices you wish to connect to your system.
D 8125 PO PEX (-) (-) (+) (+) GN D OUT IN A UX C on trol/C o m m u nica tor P an el ZON EX O UT 1 28 Z O N EX IN 1 27 Z ON EX O U T 2 26 Z O N E X IN 2 25 ZO N E X P O W E R + 24 ZO N EX C OM MO N 23 1 2 DATA AUX GND 3 4 5 6 7 8 D 8 1 2 9 O C TO R E L AY S FO R R E L AY N U M BE R S 1 TO 6 4 . C O N N E C T O C TO R E L AY S IN PA R A L L E L .
Wiring Connections Installation You can install the D811 in the enclosure with the panel (see Figure 2) or in an adjacent enclosure not more than 5 feet from the panel. Use 16 to 22 AWG wire. Follow the procedure below to install D811 modules in the enclosure with the panel. Power down the panel to connect D811 modules as shown in Figure 16. Note that the D811 for relay number 53 connects to ZONEX 1. The D811 for relay number 117 connects to ZONEX 2 on the D9412/D9112. 1.
Arming Devices Description Assigning the Command Center an Address Switches on the Command Center assign an address (1 to 8) to the Command Center. The address determines if the Command Center is supervised, the Command Center's scope, and what area the Command Center is assigned to. See Command Center Assignment in the D9412/ D9112 Program Entry Guide (74-07695-000) for a complete description of addresses.
PA N E L D8132 C O N N E C T IO N S POWER + 32 D ATA B U S A 31 D A TA B U S B 30 COMMON 29 + 12 V D C + 12 V DC D ATA COMMO N D ATA COMMON Figure 17: Power at Command Centers Switching the green and yellow wires affects other Command Centers: Incorrectly connecting the green wire from the Command Center to terminal 31 and the yellow wire to terminal 30, causes other Command Centers connected to the panel to go blank and/or sound random beep tones.
Keyswitch Operation Keyswitch Description You can connect a maintained or momentary contact arming station (keyswitch) to master arm/ disarm any of the areas in the system. The keyswitch is connected to an on-board or offboard point’s sensor loop. Relays can be programmed to activate arming status LEDs for keyswitch arming stations. See the Relays section of the D9000/D7000 Series Program Entry Guide (74-07695-000).
SDI Devices Switch Settings Description Switches on the D9131A assign a unique address (17 to 19) to each printer. The address determines if the printer is supervised, the printer's scope, and what area the printer is assigned to. See Printer Parameters in the D9000/D7000 Series Program Entry Guide (7407695-000) for a complete description of addresses. The panel can support a number of accessory devices off the SDI bus using terminals 29 through 32.
♦ D9210B Access Control Module The Radionics D9210B Access Control Interface is a 4-wire powered device providing connections for an access door point and door strike. The D9412 can supervise eight Access Control Modules, and the D7412 can supervise two Access Control Modules. Each Access Control Module supports one door to control access. Programming allows each access door to be configured independently.
Programmer and Accessory Connections Programmer Connector (J7) The procedure below shows you how to connect and disconnect the programmer. Refer to D5200 Programmer Operation Manual (74-06176-000) for complete information on using the D5200 programmer. F O R P R O GR A M M IN G PA N E L 1. Lock Reset Pin: See Figure 19 (right) and Locking the Reset Pin. 2. Connect the D5200 Data/Power cord into the programmer connector (J7). 3. Perform the desired programming function (send or receive program). 4.
74-07692-000-C FACEPLATE SHIELD HOOKS 4/97 17-05823-002 D 9412 LEDs Off When Normal Y EL RED OPERATION MONITOR LED Op eratio n Monitor Pulses W hen Normal Flicke rs W h en Ringing Dig ital Alarm, Comm unicator Tra nsmitter Charging Status GRN Low Battery Reset Pin Disable All Except Battery Charging A nd Prog rammin g RESET PIN , LO W BAT TE RY LE D (R ed) COLOR CODED BATTERY LEADS 2 C L ASS 2 T R A N S F O R M E R 16 .5 VA C 40 VA 6 0 H Z P art N o .
Quick Reference Terminal Description Terminal Name Description 1, 2 CLASS 2 TRANSFORMER 3 + AUX POWER 4 BATTERY NEGATIVE ONLY Connect 12V, 7Ah rechargeable lead acid type battery’s negative terminal (-) to terminal 4. 5 (+) BATTERY POSITIVE ONLY Connect 12V, 7Ah rechargeable lead acid type battery’s positive terminal (+). 6 (+) + STEADY OR PULSED ALARM POWER 7 (+) + ALTERNATE ALARM POWER Connect 16.5 VAC, 40 VA transformer for primary power supply. Supplies up to 1.4A at 10.2 VDC to 13.
Troubleshooting Guide Introduction Pressing "ESC" may silence the buzzer. Radionics provides this guide to help you troubleshoot problems with the D9412/D9112. To prevent problems from occurring, read the preceding sections of this manual and the Program Entry Guide to verify that the panel is correctly installed and programmed. Silencing the buzzer does not correct the problem: You must replace the corrupted copy of the program in the panel. Load a new copy of the complete program.
SERVC KEYPAD - Supervised Command Center Missing When the panel loses contact with a supervised Command Center, SERVC KEY PAD appears at other Command Centers connected to the panel. The panel transmits an SDI FAILURE report to the receiver. See also CALL FOR SERVICE. Pressing "ESC" silences the buzzer. The displays clear when contact with the missing Command Center restores.
Communications Failure The panel goes into Communications Failure after ten unsuccessful attempts to reach the receiver. Follow the Phone Line Trouble Symptom The line rings but the D6500 receiver does not pick up. Diagnosis Line is not ringing at the receiver. RING indicator on line card does not light. Can not hear ring with headset at receiver location. procedure to verify that there is no problem with the phone lines at the installation.
Problems Programming the Panel Before attempting to program the panel, you should be familiar with the basic operation of the D5200 programmer. See the D5200 Operation Manual (74-06176-000). If you still experience problems, check for the symptoms below. Symptom Diagnosis The programmer displays PLUG IN D9412 (or D9112 or D7412 or D7212) when you press SEND or RECV. The programmer is not correctly connected to the panel. Remedy 1.
Problems with Points (Continued) Symptom Diagnosis One or more points remain in trouble or alarm with all devices connected to the sensor loops normal. The sensor loop is open, shorted, or grounded. Faulted points do not generate alarms or troubles as programmed. Sensor Reset pressed at the time the alarm or trouble was generated. Remedy Remove the sensor loop from the panel or POPIT and meter it for continuity.
Problems with the D8125 POPEX Data Expansion Loops EMI (Electro-magnetic Interference), excessive resistance, or intermittent grounds, shorts, or opens on the data expansion loop can cause erratic or intermittent functioning of points. Follow the procedures below to find the source of problems on the data expansion loop. Checking Shielded Cable If improperly installed, shielded cable can create problems rather than solve them. Follow the procedure below to check shielded cable for proper installation. 1.
Problems with Command Centers Symptom Command centers show erratic behavior. For example, the pip that confirms you pressed a key "echoes." Diagnosis Remedy More than one command center has the same supervised address. Entering a supervised address in more than one command center causes erratic behavior. Supervised addresses support only one command center per address. Data connections (yellow and green wires) on one or more command centers are reversed, or only one wire is connected.
Runaway Reports to the Receiver Using the D8128 or D8128A in place of the D8128C OctoPOPIT Module may cause runaway reports to the receiver on AC failure. Be sure to replace all D8128 or D8128A OctoPOPITS with the D8128C module. Overloaded Power Supply If the load on the panel's power supply exceeds it's capacity, the panel follows a routine to protect itself and the battery. It sends reports to the Central Station at several points during this routine.
5. 6. During the Service Walk Test you may want to see the points that remain untested. When point text is displayed, press "ESC". The display shows ## PTS TO TEST. Press the "ESC" key. VIEW UNTESTED ? is displayed. Press ENT. ## PTS UNTESTED is displayed. Press NEXT to see a list of the points that have not yet been tested. Move through this list by pressing the NEXT key. To resume the Service Walk Test, press "ESC". ## PTS UNTESTED is displayed. Press "ESC". ## PTS TO TEST is displayed.
Approved Applications Compliance Guide Burglary Applications Listings and Approvals Fire UL Underwriters Laboratories lists the D9412, D9112, D7412, and D7212 Control/Communicators as Signal System Control Units for: Central Station, Local, Auxiliary, Remote Station, and Household Fire Warning. CSFM Approved by the California State Fire Marshal. NYC-MEA Approved by New York City's Materials and Equipment Acceptance System. Factory Mutual (FM) Approved by Factory Mutual.
For battery calculations, refer to Current Rating Chart for Standby Battery Calculations, Standby Battery Requirements, and Standby Battery Calculation for NFPA 72 Fire Alarm Applications. some modification, can be used for bank safe and vault applications (see the Radionics Technogram D7212/D9112 UL Certificated Bank Safe and Vault Applications, RPN: 7307302-000). UL lists the D8108A for all commercial fire alarm applications.
D 12 2 and D 12 2L D ual Ba tte ry H arne ss C alculate c u rrent draw to d ete rm in e if s eco nd b attery is requ ire d D 12 5 B P ow ered Lo o p Inte rfa ce Op t. D 12 9 C las s A In itiatin g M o du le # # # # 1+ O pt. 1+ O p t. D 92 8 D ual P ho ne Line M o dule Op t. O p t. O pt. O pt. O p t. Op t. R e qu ire d to co n n e c t p a n e l to R J 3 1 X Te lC o .
S S 16 VAC 40 VA 60 HZ TRANSFORMER P D1640 S P D8004 TRANSFORMER ENCLOSURE. REQUIRED FOR NFP A APPLICATIONS.
S S 16 VAC 40 VA 60 HZ TRANSFORMER P D1640 S P D8004 TRANSFORMER ENCLOSURE. REQUIRED FOR NFPA APPLICATIONS.
S S 16 VAC 40 VA 60 HZ TRANSFORMER D1640 P S P -+ P D8004 TRANSFORMER ENCLOSURE. REQUIRED FOR NFPA APPLICATIONS. CO MM ON + S W IT CH ED A UX POW E R + A LTER NATE + ST E A DY OR PU LS E PH ONE LE D O N WH EN CO M M U NI C ATIN G O FF WH EN ID LE R ED Ter minals 7 & 8 Requir es Optional D136 Relay in J1 & J9 PROGRAMMABLE ALARM OUTPUTS B AT TE RY PO S IT IV E O NL Y B ATTE RY NE G ATIV E O NLY M ax im um Ch arg ing Cu rrent 1.4 A m ps. + A UX P O W E R CLA SS 2 TRANSF ORM ER 16.
S 16 VAC 40 VA 60 HZ TRANSFORMER D1640 P S P -+ P D8004 TRANSFORMER ENCLOSURE. REQUIRED FOR NFP A APPLICATIONS. 8 CO M MO N S WI TCHED + A UX PO W ER + A LTE RN AT E + S TE AD Y O R P UL SE PH ONE LE D O N W HEN CO M M UNI CATI NG O FF W HEN ID L E R ED Terminals 7 & 8 Requires Optional D136 Relay in J1 & J9 P ROGRAMMABLE ALARM OUTPUTS BA TT ER Y P OS ITIV E O NL Y B A TTE RY N EG ATI VE ONLY M ax im um C hargin g C ur rent 1.4 A m ps . + AU X P O W E R CLASS 2 TRA NS FORME R 16.
Current Rating Chart for Standby Battery Calculations Model Number A B C AC Power On Normal Current AC Power Off Minimum Current In Alarm Maximum Current Quantity Used Each Unit* D9412/D9112/ D7412/D7212 ______ 350 D125B ______ 20 x Quant. = ____ 19 x Quant. = ____ 123 x Quant. = ____ D127 ______ 13 x Quant. = ____ 12 x Quant. = ____ 45 x Quant. = ____ D129 ______ 25 x Quant. = ____ 25 x Quant. = ____ 25 x Quant. = ____ D185 ______ 120 x Quant. = ____ 120 x Quant.
Standby Battery Requirements Remote Station or Auxiliary Fire Alarm Household Burglary and Commercial Burglary Four hours of standby battery capacity required. Bank Safe and Vault 72 hours of standby battery capacity required (UL 365). Aux Power current for all devices, including control centers, must be limited to 300 mA or less to meet this requirement. Central Station or Local Fire Alarm 24 hours of standby plus 5 minutes of alarm operation required.
Standby Battery Calculation for NFPA 72 Fire Alarm Applications Current Chart First See the Current Rating Chart for Standby Battery Calculations for totals B and C used in the formulas below. When connecting two batteries, use either the D122 Dual Battery Wiring Harness or the D8132 Battery Charger Module. Central Station or Local Systems Central Station or Local Systems require 24 hours of standby plus 5 minutes of alarm operation at the end of the 24 hour period.
Specifications Battery Discharge/Recharge Schedule Voltage Input Primary Power Supply 1 16.5 VAC 40 VA class 2 plug-in transformer (D1640) 2 Secondary Power Supply 4 5 12 VDC 7 Ah sealed lead acid rechargeable battery. The panel supports a maximum of two 12 VDC 7 Ah batteries using the D122 Dual Battery Harness. Discharge Cycle 13.9 VDC Charging float level 13.8 VDC Charging Status LED on 12.1 VDC Low Battery & AC fail reports if programmed, Low Battery LED on 10.
Point Thresholds D279 On-Board Points 1 to 8 Voltage Independent Zone Control (on-board and OctoPOPIT points) Resistance D442 (10") Bells D435, D448 12 VDC Horns Normal 2.3 1k Ω Short 1.85 0.657 Ω Open 2.93 1.6k Ω D1255 Command Center (General Purpose) D1255R Command Center (Red) D8103 Universal Enclosure D1256 Fire Command Center D8109 Fire Enclosure D1257 Fire Annunciator D8108A Attack Resistant Enclosure D720 Command Center (Area LED) D1640 16.
Appendix: Point Address Chart ZONEX 1, Points 9 to 127 (D9412/D9112) ZONEX 1, Points 9 to 75 (D7412/D7212) Place the labels on the base of the POPIT. Do not attach label to the POPIT cover. A number in the switch column indicates that switch is set to ON.
ZONEX 2, Points 129 to 247 (D9412/D9112 Only) A number in the switch column indicates that switch is set to ON.
