Installation Manual
Table Of Contents
- Title Page
- Table of Contents
- Certifications, approvals, listings, and safety
- Introduction
- System overview
- Installation checklist
- Control panel installation
- Power supply
- Telephone communications
- IP communications
- Keypads, keyswitches, keyfobs and transmitters
- Keypads
- B915 Basic Keypad
- B920 Two-line Alphanumeric Keypad
- B921C Two-line Capacitive Keypad with Inputs
- B930 ATM Style Alphanumeric Keypad
- B942 Touch Screen Keypad
- Shortcuts and custom functions
- Address settings
- Supervision
- Installation and control panel wiring (keypads)
- Sensor loops overview and wiring (B921C/B942/B942W only)
- Output wiring (B942/B942W only)
- Troubleshooting
- Keyswitches
- RADION keyfobs and Inovonics pendant transmitters
- Keypads
- On-board outputs
- Off-board outputs
- On-board points
- Off-board points
- Wireless modules
- Access control
- Program and test the control panel
- Control panel board overview
- System wiring diagrams
- Approved applications
- Keypad Installer menu
- [1] Program menu
- [1] Reporting > [1] Phone menu parameters
- [1] Reporting > [2] Network menu parameters
- [1] Reporting > [3] Routing menu parameters
- [1] Reporting > [4] Personal Note menu parameters
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address Parameters menu
- [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS Parameters menu
- [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module)
- [3] RPS > [1] RPS Passcode menu parameters
- [3] RPS > [2] RPS Phone Number menu parameters
- [3] RPS > [3] RPS IP Address menu parameters
- [3] RPS > [4] RPS Port Number menu parameters
- [4] Area Options menu parameters
- [5] Keypad menu parameters
- [6] Users menu parameters
- [7] Points menu parameters
- [8] Disable Programming menu
- [2] Wireless menu
- [1] RF Point Menu> [1] Enroll Point RFID
- [1] RF Point Menu> [2] Replace Point RFID
- [1] RF Point Menu> [3] Remove Point RFID
- [2] RF Repeater Menu > [1] Add Repeater
- [2] RF Repeater Menu > [2] Replace Repeater
- [2] RF Repeater Menu > [3] Remove Repeater
- [3] RF Diagnostic Menu > [1] RF Points
- [3] RF Diagnostic Menu > [2] RF Repeater Menu
- [3] Diags menu
- [4] Serv Byp (Service Bypass) menu
- [5] Versions menu
- [6] Cloud menu
- [1] Program menu
- Specifications
- Appendix
- Back Page
B93x/B94x keypads configuration of Area On
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [4] Area Options menu. The keypad shows the Area On state for the
selected area.
3. Use
/[PREV] or /[NEXT] to go to the desired area.
4. Press [Edit] to edit the Area On state for the selected area.
5. Press [Yes] or [No].
6. Press [Save] to save the programming.
7. When the keypad shows Parameter Saved, escape from the menu.
Account Number
B91x/B92x keypads configuration of Account Number
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [4] Area Options. The keypad toggles between showing the Area On
state and the account number for the selected areas.
3. Use [PREV] or [NEXT] to go to the desired area.
4. Press [ENTER] to edit the area, and then press [NEXT] to go to the account number
option.
5. Press [ENTER] to edit the account number for the selected area.
6. Delete existing characters, if necessary, and then enter the new characters.
7. Press [ENTER] to save the programming.
8. When the keypad shows Parameter Saved, escape from the menu.
B93x/B94x keypads configuration of Account Number
1. Enter the installer passcode, and then open the [1] Installer menu.
2. Go to [1] Program > [4] Area Options menu. The keypad shows the Area On state for the
selected area.
3. Use
/[PREV] or /[NEXT] to go to the desired area.
4. Press [Account #] to view and edit the account number, and then press [Edit] to edit the
account number.
5. Delete existing characters, if necessary, and then enter the new characters.
6. Press [Save] to save the programming.
7. When the keypad shows Parameter Saved, escape from the menu.
[5] Keypad menu parameters
The scope of a keypad defines which areas the keypad affects when armed (on), which areas
you can view with this keypad, and the areas to which this keypad can move. In this menu, you
can choose the keypad’s scope.
Scope (Circle one)
Keypad 1 No Device / Area Wide / Acct Wide / Panel Wide
Keypad 2 No Device / Area Wide / Acct Wide / Panel Wide
Keypad 3 No Device / Area Wide / Acct Wide / Panel Wide
Keypad 4 No Device / Area Wide / Acct Wide / Panel Wide
Keypad 5 No Device / Area Wide / Acct Wide / Panel Wide
Keypad 6 No Device / Area Wide / Acct Wide / Panel Wide
20.1.14
124 en | Keypad Installer menu Control Panel
2016.05 | 14 | F.01U.287.180 Installation and System Reference Guide Bosch Security Systems, Inc.